Electroosmotic dewatering of dredged sediments: bench-scale investigation

The Indiana Harbor (Indiana, USA) has not been dredged since 1972 due to lack of a suitable disposal site for dredged sediment. As a result of this, over a million cubic yards of highly contaminated sediment has accumulated in the harbor. Recently, the United States Army Corps of Engineers (USACE) has selected a site for the confined disposal facility (CDF) and is in the process of designing it. Although dredging can be accomplished rapidly, the disposal in the CDF has to be done slowly to allow adequate time for consolidation to occur. The sediment possesses very high moisture content and very low hydraulic conductivity, which cause consolidation to occur slowly. Consolidation of the sediment is essential in order to achieve adequate shear strength of sediments and also to provide enough air space to accommodate the large amount of sediment that requires disposal. Currently, it has been estimated that if a one 3-foot (0.9-m) thick layer of sediment was disposed of at the CDF annually, it would take approximately 10 years to dispose of all the sediment that is to be dredged from the Indiana Harbor. This study investigated the feasibility of using an electroosmotic dewatering technology to accelerate dewatering and consolidation of sediment, thereby allowing more rapid disposal of sediment into the CDF. Electroosmotic dewatering essentially involves applying a small electric potential across the sediment layer, thereby inducing rapid flow as a result of physico-chemical and electrochemical processes. A series of bench-scale electrokinetic experiments were conducted on actual dredged sediment samples from the Indiana Harbor to investigate dewatering rates caused by gravity alone, dewatering rates caused by gravity and electric potential, and the effects of the addition of polymer flocculants on dewatering of the sediments. The results showed that electroosmotic dewatering under an applied electric potential of 1.0VDC/cm could increase the rate of dewatering and consolidation by an order of magnitude as compared to gravity drainage alone. Amending the sediment with polymers at low concentrations (0.5-1% by dry weight) will enhance this dewatering process; however, the optimal polymer concentration and the cost-effectiveness of using polymers should be investigated further.     

Recycling of an industrial sludge and marine clay as light-weight aggregates

The geographical limitations of Singapore, its restricted natural resources and voluminous municipal and industrial waste streams, make environmental management a major challenge for the island state. In an attempt to find ways to reduce importation of raw materials and the waste sent to landfill, light weight aggregates were produced from marine clay and a CaF(2)-rich semiconductor industry sludge. Aggregates were produced in a bench-scale rotary kiln with three clay/sludge loadings (90/10, 70/30 and 50/50%). All three mixtures showed good bloating behavior during firing and the ceramic pellets (1-1.5cm diameter) had densities well below that required for light-weight aggregates. In the initial tests, the pore sizes of the aggregates were in general too large resulting in high water absorption. Comparisons between the composition of the two waste products and the aggregates showed a significant loss of fluorine (40-60%) during processing; a problem which may require flue gas treatment. Leach testing showed that the formed aggregates would not pose a human or environmental hazard in terms of fluorine mobilization.     

Study of the evolution of aerosol emissions from coal-fired power plants due to coagulation, condensation, and gravtitational settling and health impact

This paper studies the scavenging efficiencies of aerosol emissions from coal-fired power plants under different removal mechanisms (coagulation, heterogeneous nucleation and gravitational settling) as a function of time. It also analyses the ‘health impact’ of the aerosol before and after the above dynamic mechanisms by comparing the respirable dust fractions. The well-known equations of evolution are applied to an average PSD that represents the exhaust particulate emissions from coal-fired power plants (i.e. Aboño power plant in Asturias that belongs to Hidrocantábrico Group, S.A.). From this study it is inferred that respirable dust is scavenged with the greatest difficulty and when compared with the initial volume of respirable dust, roughly 20% remains after 18 h of gravitational settling. Therefore, gravitational settling is the main removal mechanism of respirable dust compared to condensation and coagulation.     

二氯异氰脲酸钠和二氯异氰脲酸对棕囊藻细胞去除的研究

研究了二氯异氰脲酸钠和三氯异氰脲酸对球形棕囊藻的灭杀和控制作用,及其投药时间对除藻效果的影响,并比较2种药剂的除藻效果,初步探讨了除藻机理.结果表明,这2种除藻剂可以缓释次氯酸,提高其稳定性,有较长的药效期.当有效氯浓度达到4.5mg/L时,2种药剂均能有效地控制和灭杀球形棕囊藻,具有高效、低毒的优点.有效氯浓度为5.0mg/L,藻细胞去除率在24h可达到90%以上.在等于和大于5.0mg/L有效氯浓度时,三氯异氰脲酸的除藻效果优于二氯异氰脲酸钠,通过对2种药剂除藻率的t检验进一步证实了这一结论.     

Performance Evaluation of Multiple Groundwater Flow and Nitrate Mass Transport Numerical Models

Environmental Modeling & Assessment - Benchmarking of different numerical models simulating groundwater flow and contaminant mass transport is the aim of the present study, in order to...     

Modelling the Distribution and Quality of Sand and Gravel Resources in 3D: a Case Study in the Thames Basin,UK

Three-dimensional (3D) models are often utilised to assess the presence of sand and gravel deposits. Expanding these models to provide a better indication of the suitability of the deposit as aggregate for use in construction would be advantageous. This, however, leads to statistical challenges. To be effective, models must be able to reflect the interdependencies between different criteria (e.g. depth to deposit, thickness of deposit, ratio of mineral to waste, proportion of ‘fines’) as well as the inherent uncertainty introduced because models are derived from a limited set of boreholes in a study region. Using legacy borehole data collected during a systematic survey of sand and gravel deposits in the UK, we have developed a 3D model for a 2400 km² region close to Reading, southern England. In developing the model, we have reassessed the borehole grading data to reflect modern extraction criteria and explored the most suitable statistical modelling technique. The additive log-ratio transform and the linear model of coregionalization have been applied, techniques that have been previously used to map soil texture classes in two dimensions, to assess the quality of sand and gravel deposits in the area. The application of these statistical techniques leads to a model which can be used to generate thousands of plausible realisations of the deposit which fully reflect the extent of model uncertainty. The approach offers potential to improve regional-scale mineral planning by providing an enhanced understanding of sand and gravel deposits and the extent to which they meet current extraction criteria.

     

Framing of Geoengineering Affects Support for Climate Change Mitigation

The growing recognition that climate change mitigation alone will be inadequate has led scientists and policymakers to discuss climate geoengineering. An experiment with a US sample found, contrary to previous research, that reading about geoengineering did not reduce conservatives’ skepticism about the existence of anthropogenic climate change. Moreover, depending on how it is framed, geoengineering can reduce support for mitigation among both conservatives and non-conservatives. When geoengineering is framed as a major solution, people worry less about climate change, leading to reduced mitigation support. When framed as disastrous, people perceived geoengineering as riskier, also leading to a decrease in mitigation support. A more moderate framing of geoengineering as a partial solution is less susceptible to moral hazard effects. Overall, results suggest that geoengineering will not lessen political polarization over anthropogenic climate change, and could undercut support for mitigation efforts. Instead, framing geoengineering as a small piece to solving a big puzzle seems to be the best strategy to weaken this potential moral hazard.     

Indicator framework for sustainable production planning and controlling

Production facilities serve to transform raw materials into products, usually with the goal of achieving a designated output, in terms of quantity and quality, with the minimum of cost and labour. With the aid of production planning and controlling (PPC) systems, raw material inputs, and labour can be planned to achieve a determined output of products. In general, the role of environmental and social aspects is neglected in production planning processes. Because of the growing pressure from politics and customers, sustainable production of products is becoming more important. One possibility for supporting sustainable manufacturing is, to integrate sustainable aspects in the production planning process. This paper presents input and output information for current PPC systems and discusses the need for additional information necessary for sustainable PPC. For this approach, a text review of cooperate social responsibility (CSR) reporting indicators provided by the GRI was performed. Based on the text review, an input-output model has been developed for conventional and another one for sustainable PPC systems. Through the comparison of the two input-output models, challenges and requirements for sustainable PPC systems have been defined as a basis for future work and analyses.     

Dry and heat stress affects H2S production of Salmonella on selective plating media

The pH of Salmonella pre-enrichment media can become acidic (pH 4.0–5.0) when feeds/ingredients are incubated for 24?h. Salmonella in feed that have been stressed by heat and desiccation exhibit different pH tolerances than non-stressed cultures. Acidic conditions can result in cell injury/death and affect biochemical pathways. In this study, eight serotypes of Salmonella were grown in sterile meat and bone meal that was subjected to desiccation and heat stress. Cultures of non-stressed and stressed isolates were subsequently exposed to acidic pH from 4.0 to 7.0 in 0.5?pH increments (3 replicates/pH increment) in citrate buffer. At 6 and 24?h, serial dilutions were plated in duplicate on XLT-4 (xylose lysine tergitol-4) agar. Four serotypes showed an impaired ability to decarboxylate lysine on XLT-4. This inability to decarboxylate lysine was dependent on isolate, stress status, and incubation time. When the isolates’ ability to decarboxylate lysine was examined using biochemical tests, cultures were found to be able to decarboxylate lysine with the exception of S. Infantis. This suggests that XLT-4 contains a biochemical stressor(s) which affects the rate of decarboxylation by these Salmonella. These results suggest that acidic conditions may influence the detection and confirmation of Salmonella in feed.     

Trace elements and microbiological parameters in farmed Nile tilapia with emphasis on muscle,water, sediment and feed

Fish may bioaccumulate contaminants from the aquatic environment and extend them to the food chain provoking risks to human health. This study evaluated the microbiological parameters of the pond´s water and trace elements concentrations in samples of water, sediment, feed and muscle of farmed Nile tilapia used for human consumption in southern Brazil. A total of 240 fish were collected from 12 tilapia farms. Sediment, tank water and dry ration used in the animals' diet were collected for analysis. Analysis were performed by Energy Dispersion X-ray Fluorescence (EDXRF), Inductively Coupled Plasma Mass Spectrometer (ICP-MS), Induced Coupled Plasma Optical Emission Spectrometer (ICP-OES), and Atomic Absorption Spectrometer (AAS-VGA). In addition, the microbiological analysis of the water was carried out. The concentrations of Se, I, Fe, Cu and Zn in fish muscle were higher than the recommended by the Brazilian legislation, considering the advised daily intake for adults. The arsenic element had concentrations above the limit stipulated by the present Brazilian legislation, observed in all samples of muscle, sediment and tank water highlighting a possible environmental and fish contamination by the toxic element. Moreover, the arsenic concentration in the water presented a positive correlation (ρ?=?0.33) with arsenic in the muscle, suggesting that tilapia is a good environmental bioindicator, once they properly reflect the levels of arsenic in the water. It is suggested to perform an arsenic speciation for quantification of the inorganic form and accurate assessment of the degree of toxicity in the muscle samples and risks it can bring to human health. Regarding the other potentially toxic elements (Hg, Pb and Cd), and microbiological analysis of water it was verified that the consumption of the fish in question does not raise risks, since the values are within a quality benchmark established by law. The concentration of total and fecal coliforms in pond´s water in the facilities was in agreement with the microbiological indexes required by the legislation of CONAMA class II. Western region presented the lowest concentrations of fecal coliforms when compared to the other regions. There was no significant difference in the microbiological counts of total heterotrophic bacteria, Vibrio spp. and Pseudomonas spp. among the regions.