1987 Market Outlook for Air Pollution Control and Hazardous Waste Management

Change has characterized nearly all aspects of the air pollution control industry during the last year. The supplier companies are changing due to mergers and increased activity from foreign suppliers. Both the products and the markets are changing due to developing technologies and a changing regulatory picture. Waste-to energy and VOC control are seen as growth industries in the U.S., and a resurgence is expected in the FGD and utility particulate control arenas over the next ten years. Expansion of air pollution control companies into hazardous     

Copper desorption in flooded agricultural soils and toxicity to the Florida apple snail (Pomacea paludosa): implications in Everglades restoration

Copper (Cu) desorption and toxicity to the Florida apple snail were investigated from soils obtained from agricultural sites acquired under the Comprehensive Everglades Restoration Plan. Copper concentrations in 11 flooded soils ranged from 5 to 234 mg/kg on day 0 and from 6.2 to 204 mg/kg on day 28 (steady-state). The steady-state Cu concentration in overlying water ranged from 9.1 to 308.2 microg/L. In a 28-d growth study, high mortality in snails occurred within 9 to 16 d in two of three soil treatments tested. Growth of apple snails over 28 d was affected by Cu in these two treatments. Tissue Cu concentrations by day 14 were 12-23-fold higher in snails exposed to the three soil treatments compared to controls. The endangered Florida snail kite and its main food source, the Florida apple snail, may be at risk from Cu exposure in these managed agricultural soil-water ecosystems.     

Is BDE-175 an important enough component of commercial octabromodiphenyl ether mixtures to be listed in Annex A of the Stockholm Convention?

Commercial octabromodiphenyl ether mixtures, containing hexabromodiphenyl ethers and heptabromodiphenyl ethers were listed in Annex A of the Stockholm Convention on May 2009 (Fourth Conference of the Parties) (UNEP, 2009a). Four compounds are specifically mentioned: 2,2′,4,4′,5,5′-hexabromodiphenyl ether (BDE-153), 2,2′,4,4′,5,6′-hexabromodiphenyl ether (BDE-154), 2,2′,3,3′,4,5′,6-heptabromodiphenyl ether (BDE-175), and 2,2′,3,4,4′,5′,6-heptabromodiphenyl ether (BDE-183). Presumably they were identified as key components of commercial mixtures and found to be present in environmental samples. However, since BDE-175 and BDE-183 co-elute on common HRGC columns, the presence of BDE-175 as an important component in technical octa-BDE mixtures has not been illustrated. The successful HRGC/LRMS separation of a 1:1 mixture of BDE-175 and BDE-183, as well as ¹H NMR analysis of technical material, has allowed us to confirm that this congener is not present in technical products (e.g. Great Lakes DE-79™) in quantifiable amounts.     

Simulation and evaluation of 2010 emission control scenarios in a Mediterranean area

At the onset of the 2010 statutory deadline for the respect of the European National Emission Ceiling directive, two questions arise. Will the engaged regulations for the respect of ozone air quality thresholds be fully efficient on the most polluted regions? How can we design the continuation of ozone control in those areas? This study is based on refined 3D modelling studies over a French Mediterranean region. It compares 2001 and 2003 situations with several prospective 2010 emission scenarios with, for the first time, the evaluation of local action plans. The degree of compliance with air quality regulation is investigated and the impact of emission control on the local potential for ozone formation is discussed. The results show that current efforts on emissions, although substantial and efficient, are not sufficient yet to abrogate all the ozone threshold exceedances. They also highlight the gap between regulatory and effective emission control, as well as the need for regional regulations to complete national efforts. Finally, the simulations indicate that large-scale emission control significantly helps reducing rural ozone (?20 ppbv) but affects much fewer (?2 to ?10 ppbv) the highest peaks. The continuation and the strengthening of ozone policies under their current form in such regions are considered.     

Determination of the emissions from an aircraft auxiliary power unit (APU) during the Alternative Aviation Fuel Experiment (AAFEX)

The emissions from a Garrett-AiResearch (now Honeywell) Model GTCP85-98CK auxiliary power unit (APU) were determined as part of the National Aeronautics and Space Administration's (NASA's) Alternative Aviation Fuel Experiment (AAFEX) using both JP-8 and a coal-derived Fischer Tropsch fuel (FT-2). Measurements were conducted by multiple research organizations for sulfur dioxide (SO2, total hydrocarbons (THC), carbon monoxide (CO), carbon dioxide (CO2), nitrogen oxides (NOx), speciated gas-phase emissions, particulate matter (PM) mass and number, black carbon, and speciated PM. In addition, particle size distribution (PSD), number-based geometric mean particle diameter (GMD), and smoke number were also determined from the data collected. The results of the research showed PM mass emission indices (EIs) in the range of 20 to 700 mg/kg fuel and PM number EIs ranging from 0.5 x 10(15) to 5 x 10(15) particles/kg fuel depending on engine load and fuel type. In addition, significant reductions in both the SO2 and PM EIs were observed for the use of the FT fuel. These reductions were on the order of approximately 90% for SO2 and particle mass EIs and approximately 60% for the particle number EI, with similar decreases observed for black carbon. Also, the size of the particles generated by JP-8 combustion are noticeably larger than those emitted by the APU burning the FT fuel with the geometric mean diameters ranging from 20 to 50 nm depending on engine load and fuel type. Finally, both particle-bound sulfate and organics were reduced during FT-2 combustion. The PM sulfate was reduced by nearly 100% due to lack of sulfur in the fuel, with the PM organics reduced by a factor of approximately 5 as compared with JP-8.     

Effects of Sorbent Injection on Participate Properties: Part I. Low-Temperature Sorbent Injection

Abstract

This article is the first of a two-part series dealing with the effects of sorbent injection processes on particulate properties. Part I reviews the effects on particulate properties of low-temperature sorbent injection processes (those processes that treat flue gas at temperatures near 300 °F). Part II reviews the effects on particulate properties of high-temperature sorbent injection processes (those processes that involve sorbent injection into the combustion or economizer sections of a boiler). In this article, we review what is currently known about the effects of the low-temperature sorbent injection processes on electrical resistivity, particulate mass loading, particulate size distribution, particulate morphology and cohesivity.

Mixtures of ash and sorbent produced by low-temperature sorbent injection processes are typically less cohesive than most types of fly ash. At temperatures within 30 °F of the water dew point, the combination of low cohesivity and low electrical resistivity of the ash and sorbent mixtures can cause electrical reentrainment in electrostatic precipitators. Deliquescent additives such as calcium chloride cause the water to be retained on the particle surface, thereby increasing cohesivity.

Sorbent injection has been reported to increase the particulate mass loading by a factor of 1.8 to 10, depending upon the reagent ratio and the coal sulfur content. Conventional and in-duct spray drying processes tend to shift the particle size distribution toward larger particles, while dry injection processes tend to shift the particle size distribution toward smaller particles.     

Comparative toxicity of Solvent Yellow 33 [2-(2′-quinolinyl)-1,3-indandione] and Solvent Green 3 (1,4-di-p-toluidinoanthraquinone) dyes to freshwater organisms

Solvent Yellow 33 and a Solvent Green 3 mixture (30:70 mixture of Solvent Yellow 33 and Solvent Green 3) were not acutely toxic to seven of nine freshwater species when tested at the solubility limits of the dyes in freshwater. A solubility limit solution of the Solvent Green 3 mixture killed 50% of the rainbow trout tested for 96 h but was non-toxic when diluted by 50%. Both dyes caused a reduction in green algal growth at solubility limits. The Solvent Green 3 mixture was the most detrimental causing a 98–99% reduction in growth after 5 days of exposure.     

Assessing the effects of transboundary ozone pollution between Ontario,Canada and New York,USA

We investigated the effects of transboundary pollution between Ontario and New York using both observations and modeling results. Analysis of the spatial scales associated with ozone pollution revealed the regional and international character of this pollutant. A back-trajectory-clustering methodology was used to evaluate the potential for transboundary pollution trading and to identify potential pollution source regions for two sites: CN tower in Toronto and the World Trade Center in New York City. Transboundary pollution transport was evident at both locations. The major pollution source areas for the period examined were the Ohio River Valley and Midwest. Finally, we examined the transboundary impact of emission reductions through photochemical models. We found that emissions from both New York and Ontario were transported across the border and that reductions in predicted O3 levels can be substantial when emissions on both sides of the border are reduced.