Determination of trace metal concentrations in soil profiles of municipal waste dumps in Nigeria

The concentrations of trace metals (Cd, Pb, Cu, Cr, Fe, Ni, Zn and Co) were studied in soil profiles of eight municipal waste dump sites in Warri metropolis. The results indicate that concentrations of trace metals varied widely among the different dumpsites and decreased with depths in a studied soil profile. The accumulation pattern for the heavy metals in the soil profiles follows the order: Fe > Pb > Mn > Co > Cr > Zn > Ni > Cu > Cd. The concentrations of metals found in these sites was below the Canadian remediation criteria for land for agricultural, residential and commercial/industrial purposes except for the cadmium levels in some sites that exceeded criterion values for agricultural and residential. In such sites, remedial actions are required before any form of chosen development can take place. The levels of heavy metals found in these dump sites were higher than that of the control site. The examined metals showed no significant correlation with soil physicochemical properties at the surface horizon, which is suggestive evidence that these metals arise from anthropogenic input.     

Growth of northern deciduous trees under increasing atmospheric humidity: possible mechanisms behind the growth retardation

Regional Environmental Change - Increasing atmospheric humidity—a climate trend predicted for northern Europe—will reduce water flux through vegetation. Diminished transpirational water...     

The emergence of an environmental governance network: the case of the Arizona borderlands

Regional Environmental Change - Across the country, government agencies increasingly collaborate with non-governmental actors on environmental dilemmas to gain access to resources, expertise, and...     

Application of carbon adsorbents prepared from Brazilian-pine fruit shell for the removal of reactive orange 16 from aqueous solution: Kinetic,equilibrium, and thermodynamic studies

Activated (AC-PW) and non-activated (C-PW) carbonaceous materials were prepared from the Brazilian-pine fruit shell (Araucaria angustifolia) and tested as adsorbents for the removal of reactive orange 16 dye (RO-16) from aqueous effluents. The effects of shaking time, adsorbent dosage and pH on the adsorption capacity were studied. RO-16 uptake was favorable at pH values ranging from 2.0 to 3.0 and from 2.0 to 7.0 for C-PW and AC-PW, respectively. The contact time required to obtain the equilibrium using C-PW and AC-PW as adsorbents was 5 and 4 h at 298 K, respectively. The fractionary-order kinetic model provided the best fit to experimental data compared with other models. Equilibrium data were better fit to the Sips isotherm model using C-PW and AC-PW as adsorbents. The enthalpy and entropy of adsorption of RO-16 were obtained from adsorption experiments ranging from 298 to 323 K.     

Reorienting Systematic Conservation Assessment for Effective Conservation Planning

Abstract: Systematic conservation assessment (an information‐gathering and prioritization process used to select the spatial foci of conservation initiatives) is often considered vital to conservation‐planning efforts, yet published assessments have rarely resulted in conservation action. Conservation assessments may lead more directly to effective conservation action if they are reoriented to inform conservation decisions. Toward this goal, we evaluated the relative priority for conservation of 7 sites proposed for the first forest reserves in the Union of the Comoros, an area with high levels of endemism and rapidly changing land uses in the western Indian Ocean. Through the analysis of 30 indicator variables measured at forest sites and nearby villages, we assessed 3 prioritization criteria at each site: conservation value, threat to loss of biological diversity from human activity, and feasibility of reserve establishment. Our results indicated 2 sites, Yiméré and Hassera‐Ndrengé, were priorities for conservation action. Our approach also informed the development of an implementation strategy and enabled an evaluation of previously unexplored relations among prioritization criteria. Our experience suggests that steps taken to ensure the closer involvement of practitioners, include a broader range of social data, encourage stakeholder participation, and consider the feasibility of conservation action can improve the relevance of assessments for conservation planning, strengthen the scientific basis for conservation decisions, and result in a more realistic evaluation of conservation alternatives.     

Characterization of particulate matter concentrations during controlled indoor activities

Indoor sources have been identified as a major contributor to the increase of particle concentration in indoor environments. The work presented here is a study of the characteristics of particulate matter number size distribution and mass concentration under controlled indoor activities in a laboratory room. The objective is to characterize particulate matter concentrations indoors resulted under the influence of specific sources. Measurements were performed in an empty laboratory (period September–October 2006) using a GRIMM SMPS+C system (particle size range between 11.1 and 1083.3 nm), a DustTrak Aerosol Monitor (TSI) and a P-Trak Ultrafine Particle Counter (TSI). The studied indoor activities included candle burning, hot plate heating, water boiling, onion frying, vacuuming, hair drying, hair spraying, smoking and burning of incense stick. The AMANpsd computer algorithm was used to evaluate the modal structure of measured particle number size distribution data. Furthermore, the change of the particle number size distribution shape under the influence of different emission sources was studied versus time. Finally the particle emission rates were computed. High particle number concentrations were observed during smoking, onion frying, candle burning and incense stick burning. The highest particle mass concentrations were measured during smoking and hair spraying. The shift of the particle size distribution to larger diameters suggests the presence of strong coagulation effect during candle burning, incense stick burning, smoking and onion frying. The size distribution was mainly bimodal during onion frying and candle burning, whereas the size distribution remained unimodal during incense stick burning and smoking experiments.     

Review of LCA studies of solid waste management systems – Part II: Methodological guidance for a better practice

Life cycle assessment (LCA) is increasingly used in waste management to identify strategies that prevent or minimise negative impacts on ecosystems, human health or natural resources. However, the quality of the provided support to decision- and policy-makers is strongly dependent on a proper conduct of the LCA. How has LCA been applied until now? Are there any inconsistencies in the past practice? To answer these questions, we draw on a critical review of 222 published LCA studies of solid waste management systems. We analyse the past practice against the ISO standard requirements and the ILCD Handbook guidelines for each major step within the goal definition, scope definition, inventory analysis, impact assessment, and interpretation phases of the methodology. Results show that malpractices exist in several aspects of the LCA with large differences across studies. Examples are a frequent neglect of the goal definition, a frequent lack of transparency and precision in the definition of the scope of the study, e.g. an unclear delimitation of the system boundaries, a truncated impact coverage, difficulties in capturing influential local specificities such as representative waste compositions into the inventory, and a frequent lack of essential sensitivity and uncertainty analyses. Many of these aspects are important for the reliability of the results. For each of them, we therefore provide detailed recommendations to practitioners of waste management LCAs.     

Environmentally Friendly Polyurethane Composites: Preparation, Characterization and Mechanical Properties

The waterborne polyurethane (PU) prepolymer was prepared based on isophorone diisocyanate (IPDI), polyester polyol (N220), dimethylol propionic acid (DMPA) and hydroxyethyl methyl acrylate (HEMA). The modified waterborne polyurethane–acrylate (PUA) emulsions were obtained with different proportions of acrylate (butyl acrylate and methyl methacrylate) and initiating agent by in situ dispersion technique. The structures and thermal properties of prepared PU and PUA were analyzed and characterized with FT-IR, UV–Vis spectroscopy and DSC. The PUA hybrid samples had lower glass transition temperature of hard segment and higher decomposition temperatures than PU sample. Performances of the emulsion and film were studied by means of apparent viscidity, particle size and polydispersity, surface tension and mechanical properties. The results indicated that the particle sizes of the PUA dispersions were larger than those of the pure PU and the solvent resistance, mechanical properties of PUA films was improved compare with the unmodified polyurethane film. The film had the biggest hardness and the least water absorption when the BA/MMA mass ratio 5:5 modified PU. The obtained PUA have great potential application such as coatings, leather finishing, adhesives, sealants, plastic coatings and wood finishes.     

The Plume Volume Molar Ratio Method for Determining NO2/NOx Ratios in Modeling—Part II: Evaluation Studies

ABSTRACT

A previous paper¹ discusses the methodology for a new method for deriving the nitrogen dioxide/nitrogen oxide (NO₂/NO_x) ratio in plumes that originally are composed mainly of (NO_x). It is called the Plume Volume Molar Ratio Method (PVMRM). This paper documents its performance against six different data sets. These performance evaluations show that the PVMRM can realistically predict the NO₂ fraction at close-in receptors yet still provide conservative estimates so that the air quality standards can be protected.