Removal of dinitrotoluenes from water via reduction with iron and peroxidase-catalyzed oxidative polymerization: a comparison between Arthromyces ramosus peroxidase and soybean peroxidase

A two-step process for the removal of dinitrotoluene from water is presented: zero-valent iron reduction is coupled with peroxidase-catalyzed polymerization of the resulting diaminotoluenes (DAT). The effect of pH was examined in the reduction step: at pH 6 the reaction occurred much more rapidly than at pH 8. In the second step, optimal pH and substrate ratio, minimal enzyme concentration and effect of polyethylene glycol (PEG) as an additive for greater than 95% conversion of DAT, over a 3h reaction period were determined using high performance liquid chromatography. Two enzymes were investigated and compared: Arthromyces ramosus peroxidase (ARP) and soybean peroxidase (SBP). The optimal pH values were 5.4 and 5.2 for ARP and SBP, respectively, but SBP was more resistant to mild acid whereas ARP was more stable in neutral solutions. SBP was found to have a greater hydrogen peroxide demand (optimal peroxide/DAT molar ratio for SBP: 2.0 and 3.0 for 2,4-diaminotoluene (2,4-DAT) and 2,6-diaminotoluene (2,6-DAT), respectively; for ARP: 1.5 and 2.75 for 2,4-DAT and 2,6-DAT, respectively) but required significantly less enzyme (0.01 and 0.1 U ml(-1) for 2,4-DAT and 2,6-DAT, respectively) to convert the DAT than ARP (0.4 and 1.5 U ml(-1) for 2,4-DAT and 2,6-DAT, respectively). PEG was shown to have no effect upon the degree of substrate conversion for either enzyme.     

Water Quality Changes in Chini Lake, Pahang, West Malaysia

A study of the water quality changes of Chini Lake was conducted for 12 months, which began in May 2004 and ended in April 2005. Fifteen sampling stations were selected representing the open water body in the lake. A total of 14 water quality parameters were measured and Malaysian Department of Environment Water Quality Index (DOE-WQI) was calculated and classified according to the Interim National Water Quality Standard, Malaysia (INWQS). The physical and chemical variables were temperature, dissolved oxygen (DO), conductivity, pH, total dissolved solid (TDS), turbidity, chlorophyll-a, biochemical oxygen demand (BOD), chemical oxygen demand (COD), total suspended solid (TSS), ammonia-N, nitrate, phosphate and sulphate. Results show that base on Malaysian WQI, the water in Chini Lake is classified as class II, which is suitable for recreational activities and allows body contact. With respect to the Interim National Water Quality Standard (INWQS), temperature was within the normal range, conductivity, TSS, nitrate, sulphate and TDS are categorized under class I. Parameters for DO, pH, turbidity, BOD, COD and ammonia-N are categorized under class II. Comparison with eutrophic status indicates that chlorophyll-a concentration in the lake was in mesotrophic condition. In general water quality in Chini Lake varied temporally and spatially, and the most affected water quality parameters were TSS, turbidity, chlorophyll-a, sulphate, DO, ammonia-N, pH and conductivity.     

Effect of metal tolerant plant growth promoting Bradyrhizobium sp. (vigna) on growth, symbiosis, seed yield and metal uptake by greengram plants

The nickel and zinc tolerant plant growth promoting Bradyrhizobium sp. (vigna) RM8 was isolated from nodules of greengram, grown in metal contaminated Indian soils. The plant growth promoting (PGP) potentials of strain RM8 was assessed both in the presence and absence of nickel and zinc under in vitro conditions. Strain RM8 tolerated a high level of nickel (300 microg ml(-1)) and zinc (1400 microg ml(-1)) on yeast extract mannitol agar medium. Bradyrhizobium sp. (vigna) strain RM8 produced 13.3 microg ml(-1) of indole acetic acid in Luria Bertani broth at 100 microg ml(-1) of tryptophan which increased to 13.6 microg ml(-1) at 50 microg Ni ml(-1) and 13.5 microg ml(-1) at 300 microg Zn ml(-1). Strain RM8 was positive for siderophore, HCN and ammonia both in the absence and presence of nickel and zinc. The PGP activity of this strain was further evaluated with increasing concentrations of nickel and zinc using greengram as a test crop. The bioinoculant enhanced the nodule numbers by 82%, leghaemoglobin by 120%, seed yield by 34%, grain protein by 13%, root N by 41% and shoot N by 37% at 290 mg Ni kg(-1) soil. At 4890 mg Zn kg(-1) soil, the bioinoculant increased the nodule numbers by 50%, leghaemoglobin by 100%, seed yield by 36%, grain protein by 13%, root N by 47% and shoot N by 42%. The bioinoculant strain RM8 reduced the uptake of nickel and zinc by plant organs compared to plants grown in the absence of bioinoculant. This study suggested that the bioinoculant due to its intrinsic abilities of growth promotion and attenuation of the toxic effects of nickel and zinc could be exploited for remediation of metal from nickel and zinc contaminated sites.     

A Solvent-Free Approach for Production of Films from Pectin and Fungal Biomass

Self-binding ability of the pectin molecules was used to produce pectin films using the compression molding technique, as an alternative method to the high energy-demanding and solvent-using casting technique. Moreover, incorporation of fungal biomass and its effects on the properties of the films was studied. Pectin powder plasticized with 30% glycerol was subjected to heat compression molding (120 °C, 1.33 MPa, 10 min) yielding pectin films with tensile strength and elongation at break of 15.7 MPa and 5.5%, respectively. The filamentous fungus Rhizopus oryzae was cultivated using the water-soluble nutrients obtained from citrus waste and yielded a biomass containing 31% proteins and 20% lipids. Comparatively, the same strain was cultivated in a semi-synthetic medium resulting in a biomass with higher protein (60%) and lower lipid content (10%). SEM images showed addition of biomass yielded films with less debris compared to the pectin films. Incorporation of the low protein content biomass up to 15% did not significantly reduce the mechanical strength of the pectin films. In contrast, addition of protein-rich biomass (up to 20%) enhanced the tensile strength of the films (16.1–19.3 MPa). Lastly, the fungal biomass reduced the water vapor permeability of the pectin films.     

Synthesis,Characterization and Environmental Applications of a New Bio-Composite Gelatin-Zr(IV) Phosphate

Gelatin-Zr(IV) phosphate composite (GT/ZPC) was synthesized by sol–gel method. Different techniques viz. Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray powdered diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used for the characterisation of GT/ZPC composite ion exchanger. The ion exchange capacity (IEC) of GT/ZPC was observed to be better (1.04 meq g^?1) than its inorganic counterpart (0.64 meq g^?1). The pH studies revealed the monofunctional nature of GT/ZPC with one inflection point. The distribution studies showed that the GT/ZPC was highly selective for Cd²⁺ as compare to other metal ions. The environmental applicability of ion exchanger has been analysed for binary separations of metal ions using column method. Cd²⁺ was effectively removed from synthetic mixture of metal ions (Zn²⁺, Pb²⁺, Ni²⁺, Co²⁺ and Cu²⁺).     

Performance of Cow Dung Reinforced Biodegradable Poly(Lactic Acid) Biocomposites for Structural Applications

In this work, performance of cow dung (CD) reinforced poly(lactic acid) (PLA) biocomposites was investigated for the potential use in load bearing application. CD of average 4 mm size was blended with PLA at different CD ratios (0–50 wt%) and their effects on the biocomposite properties were studied. The results showed an improvement in the flexural properties, while the tensile and impact strength dropped by 20 and 28% with the addition of 50% CD. The decline in the tensile and impact strength was due to micro-cracking and voids formation at higher CD content. Also, the incorporation of CD slightly decreased the thermal stability of the biocomposite. However, dynamic mechanical properties of the biocomposites generally improved. SEM analysis of tensile and impact fractured surfaces indicated that the CD had a reasonable adhesion with matrix. Moreover, the SEM micrographs of soil burial studies showed an accelerated degradation of higher CD wt% biocomposites.     

Application of 1D and 2D MFR reactor technology for the isolation of insecticidal and anti-microbial properties from pyrolysis bio-oils

Valuable chemicals can be separated from agricultural residues by chemical or thermochemical processes. The application of pyrolysis has already been demonstrated as an efficient means to produce a liquid with a high concentration of desired product. The objective of this study was to apply an insect and microorganism bioassay-guided approach to separate and isolate pesticidal compounds from bio-oil produced through biomass pyrolysis. Tobacco leaf (Nicotianata bacum), tomato plant (Solanum lycopersicum), and spent coffee (Coffea arabica) grounds were pyrolyzed at 10°C/min from ambient to 565°C using the mechanically fluidized reactor (MFR). With one-dimensional (1D) MFR pyrolysis, the composition of the product vapors varied as the reactor temperature was raised allowing for the selection of the temperature range that corresponds to vapors with a high concentration of pesticidal properties. Further product separation was performed in a fractional condensation train, or 2D MFR pyrolysis, thus allowing for the separation of vapor components according to their condensation temperature. The 300–400°C tobacco and tomato bio-oil cuts from the 1D MFR showed the highest insecticidal and anti-microbial activity compared to the other bio-oil cuts. The 300–350 and 350–400°C bio-oil cuts produced by 2D MFR had the highest insecticidal activity when the bio-oil was collected from the 210°C condenser. The tobacco and tomato bio-oil had similar insecticidal activity (LC₅₀ of 2.1 and 2.2 mg/mL) when the bio-oil was collected in the 210°C condenser from the 300–350°C reactor temperature gases. The 2D MFR does concentrate the pesticidal products compared to the 1D MFR and thus can reduce the need for further separation steps such as solvent extraction.