Domestic water conservation potential in Saudi Arabia

Domestic water conservation in arid climates can result in efficient utilization of existing water supplies. The impacts of conservation measures such as the installation of water-saving devices, water metering and pricing schemes, water rationing and public awareness programs, strict plumbing codes, penalties for wasting water, programs designed to reduce leakage from public water lines and within the home, water-efficient landscaping, economic and ethical incentives are addressed in detail. Cost savings in arid climates, with particular reference to Saudi Arabia, in relation to some conservation techniques, are presented. Water conservation technology and tentative demonstration and implementation of water conservation programs are discussed.     

An experimental investigation into micro ball end-milling of silicon

Silicon is a representative operational material for semiconductor and micro-electronics. In certain MEMS applications, it is required to fabricate three dimensional channels and complex pattern on silicon substrate. Such features are typically fabricated by photolithography and chemical etching. These processes have low productivity and have certain other limitations. Therefore, a viable switch-over from non-traditional fabrication processes to traditional machining is highly desired for improved productivity in high-mix low-volume production. However, machining of silicon by traditional process is extremely difficult due to its high brittleness. Even very small forces produced during machining can cause brittle fracture on silicon surface resulting in deteriorated surface quality. The fundamental principle in machining of a brittle material such as silicon is to achieve material removal through plastic deformation rather than crack propagation. This paper presents the experimental results of ductile-mode machining of silicon by micro ball end-milling. The workpiece surface was inclined to the rotational axes of the cutter to improve the surface finish. It was established experimentally that 15-μm deep, fracture-free slots can be machined on silicon wafer by micro ball end-milling if the feed rate is below a certain threshold. The influence of several machining parameters on the roughness of machined-surface was also investigated. Cubic boron nitride (CBN) is presented as much economical alternative tool-material to single-crystal diamond for machining silicon in ductile-mode.     

Re-evaluating the dynamic role of shadow economy and environmental policy stringency in the energy-growth nexus in China

Environmental Science and Pollution Research - This paper examines the impact of shadow economy and environmental policy stringency on energy consumption and economic growth in the case of China...     

Leachate characterization in semi-aerobic and anaerobic sanitary landfills: A comparative study

This study analyzes and compares the results of leachate composition at the semi-aerobic Pulau Burung Landfill Site (PBLS) (unaerated pond and intermittently aerated pond) and the anaerobic Kulim Sanitary Landfill in the northern region of Malaysia. The raw samples were collected and analyzed for twenty parameters. The average values of the parameters such as phenols (1.2, 6.7, and 2.6 mg/L), total nitrogen (448, 1200, and 300 mg/L N-TN), ammonia-N (542, 1568, and 538 mg/L NH₃-N), nitrite (91, 49, and 52 mg/L NO₂^?-N), total phosphorus (21, 17, and 19 mg/L), BOD₅ (83, 243, and 326 mg/L), COD (935, 2345, and 1892 mg/L), BOD₅/COD (0.096,0.1124,0.205%), pH (8.20, 8.28, and 7.76), turbidity (1546, 180, and 1936 Formazin attenuation units (FAU)), and color (3334, 3347, and 4041 Pt Co) for leachate at the semi-aerobic PBLS (unaerated and intermittently aerated) and the anaerobic Kulim Sanitary Landfill were recorded, respectively. The obtained results were compared with previously published data and data from the Malaysia Environmental Quality Act 1974. The results indicated that Pulau Burung leachate was more stabilized compared with Kulim leachate. Furthermore, the aeration process in PBLS has a considerable effect on reducing the concentration of several pollutants. The studied leachate requires treatment to minimize the pollutants to an acceptable level prior to discharge into water courses.     

Adsorptive removal of phosphate by the bimetallic hydroxide nanocomposites embedded in pomegranate peel

This study aimed to fabricate new and effective material for the efficiency of phosphate adsorption.Two types of adsorbent materials,the zirconium hydroxides embedded in pomegranate peel(Zr/Peel) and zirconium-lanthanum hydroxides embedded in pomegranate peel(Zr-La/Peel) were developed.Scanning electronic microscopy(SEM),x-ray photoelectron spectroscopy(XPS) and x-ray diffraction(XRD) were evaluated to give insight into the physicochemical properties of these adsorbents.Zr-La/Peel exceeded the a...     

Fresh evidence on connectedness between prominent markets during COVID-19 pandemic

Environmental Science and Pollution Research - Various empirical studies have examined the nexus between financial markets, but this study focused on the comovement among prominent markets. Our...     

Wetting mechanism and morphological adaptation; leaf rolling enhancing atmospheric water acquisition in wheat crop—a review

Environmental Science and Pollution Research - Several plant species such as grasses are dominant in many habitats including arid and semi-arid areas. These species survive in these regions by...     

Monitoring of copper accumulation in water,soil, forage,and cows impacted by heavy automobiles in Sargodha,Pakistan

Environmental Science and Pollution Research - The instant endeavor was undertaken to monitor copper (Cu) contents in water, soil, forage, and cow’s blood impacted by heavy automobiles in...