Optimal deployment of emissions reduction technologies for construction equipment

The objective of this research was to develop a multiobjective optimization model to deploy emissions reduction technologies for nonroad construction equipment to reduce emissions in a cost-effective and optimal manner. Given a fleet of construction equipment emitting different pollutants in the nonattainment (NA) and near -nonattainment (NNA) counties of a state and a set of emissions reduction technologies available for installation on equipment to control pollution/emissions, the model assists in determining the mix of technologies to be deployed so that maximum emissions reduction and fuel savings are achieved within a given budget. Three technologies considered for emissions reduction were designated as X, Y, and Z to keep the model formulation general so that it can be applied for any other set of technologies. Two alternative methods of deploying these technologies on a fleet of equipment were investigated with the methods differing in the technology deployment preference in the NA and NNA counties. The model having a weighted objective function containing emissions reduction benefits and fuel-saving benefits was programmed with C++ and ILOG-CPLEX. For demonstration purposes, the model was applied for a selected construction equipment fleet owned by the Texas Department of Transportation, located in NA and NNA counties of Texas, assuming the three emissions reduction technologies X, Y, and Z to represent, respectively, hydrogen enrichment, selective catalytic reduction, and fuel additive technologies. Model solutions were obtained for varying budget amounts to test the sensitivity of emissions reductions and fuel-savings benefits with increasing the budget. Different mixes of technologies producing maximum oxides of nitrogen (NO(x)) reductions and total combined benefits (emissions reductions plus fuel savings) were indicated at different budget ranges. The initial steep portion of the plots for NO(x) reductions and total combined benefits against budgets for different combinations of emissions reduction technologies indicated a high benefit-cost ratio at lower budget amounts. The rate of NO(x) reductions and the increase of combined benefits decreased with increasing the budget, and with the budget exceeding certain limits neither further NO(x) reductions nor increased combined benefits were observed. Finally, the Pareto front obtained would enable the decision-maker to achieve a noninferior optimal combination of total NO(x) reductions and fuel-savings benefits for a given budget.     

Hydrocarbon degradation, plant colonization and gene expression of alkane degradation genes by endophytic Enterobacter ludwigii strains

The genus Enterobacter comprises a range of beneficial plant-associated bacteria showing plant growth promotion. Enterobacter ludwigii belongs to the Enterobacter cloacae complex and has been reported to include human pathogens but also plant-associated strains with plant beneficial capacities. To assess the role of Enterobacter endophytes in hydrocarbon degradation, plant colonization, abundance and expression of CYP153 genes in different plant compartments, three plant species (Italian ryegrass, birdsfoot trefoil and alfalfa) were grown in sterile soil spiked with 1% diesel and inoculated with three endophytic E. ludwigii strains. Results showed that all strains were capable of hydrocarbon degradation and efficiently colonized the rhizosphere and plant interior. Two strains, ISI10-3 and BRI10-9, showed highest degradation rates of diesel fuel up to 68% and performed best in combination with Italian ryegrass and alfalfa. All strains expressed the CYP153 gene in all plant compartments, indicating an active role in degradation of diesel in association with plants.     

Water pollution in Pakistan and its impact on public health--a review

Water pollution is one of the major threats to public health in Pakistan. Drinking water quality is poorly managed and monitored. Pakistan ranks at number 80 among 122 nations regarding drinking water quality. Drinking water sources, both surface and groundwater are contaminated with coliforms, toxic metals and pesticides throughout the country. Various drinking water quality parameters set by WHO are frequently violated. Human activities like improper disposal of municipal and industrial effluents and indiscriminate applications of agrochemicals in agriculture are the main factors contributing to the deterioration of water quality. Microbial and chemical pollutants are the main factors responsible exclusively or in combination for various public health problems. This review discusses a detailed layout of drinking water quality in Pakistan with special emphasis on major pollutants, sources of pollution and the consequent health problems. The data presented in this review are extracted from various studies published in national and international journals. Also reports released by the government and non-governmental organizations are included.     

Leachate characterization in semi-aerobic and anaerobic sanitary landfills: A comparative study

This study analyzes and compares the results of leachate composition at the semi-aerobic Pulau Burung Landfill Site (PBLS) (unaerated pond and intermittently aerated pond) and the anaerobic Kulim Sanitary Landfill in the northern region of Malaysia. The raw samples were collected and analyzed for twenty parameters. The average values of the parameters such as phenols (1.2, 6.7, and 2.6 mg/L), total nitrogen (448, 1200, and 300 mg/L N-TN), ammonia-N (542, 1568, and 538 mg/L NH₃-N), nitrite (91, 49, and 52 mg/L NO₂^?-N), total phosphorus (21, 17, and 19 mg/L), BOD₅ (83, 243, and 326 mg/L), COD (935, 2345, and 1892 mg/L), BOD₅/COD (0.096,0.1124,0.205%), pH (8.20, 8.28, and 7.76), turbidity (1546, 180, and 1936 Formazin attenuation units (FAU)), and color (3334, 3347, and 4041 Pt Co) for leachate at the semi-aerobic PBLS (unaerated and intermittently aerated) and the anaerobic Kulim Sanitary Landfill were recorded, respectively. The obtained results were compared with previously published data and data from the Malaysia Environmental Quality Act 1974. The results indicated that Pulau Burung leachate was more stabilized compared with Kulim leachate. Furthermore, the aeration process in PBLS has a considerable effect on reducing the concentration of several pollutants. The studied leachate requires treatment to minimize the pollutants to an acceptable level prior to discharge into water courses.     

Myco- and phyco-remediation of polychlorinated biphenyls in the environment: a review

Environmental Science and Pollution Research - Polychlorinated biphenyls (PCBs) are toxic organic compounds and pose serious threats to environment and public health. PCBs still exist in different...     

Domestic water conservation potential in Saudi Arabia

Domestic water conservation in arid climates can result in efficient utilization of existing water supplies. The impacts of conservation measures such as the installation of water-saving devices, water metering and pricing schemes, water rationing and public awareness programs, strict plumbing codes, penalties for wasting water, programs designed to reduce leakage from public water lines and within the home, water-efficient landscaping, economic and ethical incentives are addressed in detail. Cost savings in arid climates, with particular reference to Saudi Arabia, in relation to some conservation techniques, are presented. Water conservation technology and tentative demonstration and implementation of water conservation programs are discussed.     

Enrichment and isolation of endosulfan-degrading microorganisms

Endosulfan (6,7,8,9,10,10-hexachloro-1,5,5a,6,9,9a-hexahydro-6,9-methano-2,3,4-benzo-dioxathiepin-3-oxide) is a cyclodiene organochlorine currently used as an insecticide all over the world and its residues are posing a serious environmental threat. This study reports the isolation and identification of enriched microorganisms, capable of degrading endosulfan. Enrichment was achieved by using the insecticide as either the sole source of carbon or sulfur in parallel studies. Two strains each of fungi (F1 and F4) and bacteria (BF2 and B4) were selected using endosulfan as a sole carbon source. A Pandoraea species (Lin-3) previously isolated in our laboratory using lindane (gamma-HCH) as a carbon source was also screened for endosulfan degradation. F1 and F4 (Fusarium ventricosum) degraded alpha-endosulfan by as much as 82.2 and 91.1% and beta-endosulfan by 78.5 and 89.9%, respectively, within 15 d of incubation. Bacterial strains B4 and Lin-3 degraded alpha-endosulfan up to 79.6 and 81.8% and beta-endosulfan up to 83.9 and 86.8%, respectively, in 15 d. Among the bacterial strains isolated by providing endosulfan as a sulfur source, B4s and F4t degraded alpha-endosulfan by as much as 70.4 and 68.5% and beta-endosulfan by 70.4 and 70.8%, respectively, after 15 d. Degradation of the insecticide occurred concomitant with bacterial growth reaching an optical density (OD600) of 0.366 and 0.322 for B4 and Lin-3, respectively. High OD600 was also noted with the other bacterial strains utilizing endosulfan as a sulfur source. Fungal and bacterial strains significantly decreased the pH of the nutrient culture media while growing on endosulfan. The results of this study suggest that these novel strains are a valuable source of potent endosulfan-degrading enzymes for use in enzymatic bioremediation.     

An experimental investigation into micro ball end-milling of silicon

Silicon is a representative operational material for semiconductor and micro-electronics. In certain MEMS applications, it is required to fabricate three dimensional channels and complex pattern on silicon substrate. Such features are typically fabricated by photolithography and chemical etching. These processes have low productivity and have certain other limitations. Therefore, a viable switch-over from non-traditional fabrication processes to traditional machining is highly desired for improved productivity in high-mix low-volume production. However, machining of silicon by traditional process is extremely difficult due to its high brittleness. Even very small forces produced during machining can cause brittle fracture on silicon surface resulting in deteriorated surface quality. The fundamental principle in machining of a brittle material such as silicon is to achieve material removal through plastic deformation rather than crack propagation. This paper presents the experimental results of ductile-mode machining of silicon by micro ball end-milling. The workpiece surface was inclined to the rotational axes of the cutter to improve the surface finish. It was established experimentally that 15-μm deep, fracture-free slots can be machined on silicon wafer by micro ball end-milling if the feed rate is below a certain threshold. The influence of several machining parameters on the roughness of machined-surface was also investigated. Cubic boron nitride (CBN) is presented as much economical alternative tool-material to single-crystal diamond for machining silicon in ductile-mode.     

The global partnership for sustainable development

This paper examines whether foreign aid, together with other economic, social and environmental factors, contributes to sustainable development. It starts with an illustrative theoretical growth model where foreign aid promotes sustainable development by protecting the environment. Using factor analysis and newly developed estimation methods for a dynamic panel data model with endogenous regressors, the empirical section of the paper finds evidence that foreign aid has had a significantly positive influence on sustainable development in aid recipient countries. This effect is very likely to go through channels related to growth and resources as well as a technology channel with respect to energy intensity. This research has important implications for a post‐2015 development framework on international collective action with regard to a sustainable future.