Extent and causes of 3D spatial variations in potential N mineralization and the risk of ammonium and nitrate leaching from an N-impacted permanent grassland near York, UK

Changes in the dynamics of inorganic N species transformations with depth have been investigated for seven soil profiles from a nitrogen-impacted ancient grassland on a nature reserve outside York in the UK, using incubation experiments. In five of the profiles, both ammonification and nitrification are occurring below the rooting zone, probably partly in response to the low C:N ratio in the soils. This contributes to elevated nitrate concentrations found in an adjacent stream. Accumulation of ammonium during incubation in the sub-soils of these five profiles suggests a high probability of ammonium leaching down the profiles as ammonium inputs and outputs at a given depth approach equilibrium. This ammonium may also be nitrified at depth. However, in the two profiles with the most acidic surface horizons, net mineralization was negligible or negative; some initial ammonium-N and ammonium-N produced during incubation were nitrified, so the loss in ammonium-N was closely balanced by nitrate-N production.     

Effect of biocides on the precipitation of calcium fluoride in the presence of anionic copolymeric inhibitors

The inhibitory efficiency of anionic copolymers and the effect of the biocides sodium hypochlorite, glutaraldehyde, and tris(hydroxymethyl)nitromethane on the precipitation behavior of calcium fluoride (CaF₂) were studied. The efficiency of polymeric inhibitors was traced from conductivity measurements by using half-life (t_1/2) method. X-ray diffraction parameters have been measured for calcium fluoride scale minerals. An anionic copolymer (K-798) acts as one of the best inhibitors for the precipitation process of the calcium fluoride in water as compared to K-775. It is assigned to the fact that the copolymer (K-798) contains both sulfonic acid and sulfonated styrene groups while the polymer (K-775) having only the sulfonic acid group. It was further observed that the biocides have no appreciable effect on the performance of the anionic polymeric inhibitors.     

Assessment of tap water quality and corrosion scales from the selected distribution systems in northern Pakistan

Corrosion deposits formed within drinking water distribution systems deteriorate drinking water quality and resultantly cause public health consequences. In the present study, an attempt was made to investigate the concurrent conditions of corrosion scales and the drinking water quality in selected water supply schemes (WSS) in districts Chitral, Peshawar, and Abbottabad, northern Pakistan. Characterization analyses of the corrosion by-products revealed the presence of α-FeOOH, γ-FeOOH, Fe₃O₄, and SiO₂ as major constituents with different proportions. The constituents of all the representative XRD peaks of Peshawar WSS were found insignificant as compared to other WSS, and the reason could be the variation of source water quality. Well-crystallized particles in SEM images indicated the formation of dense oxide layer on corrosion by-products. A wider asymmetric vibration peak of SiO₂ appeared only in Chitral and Abbottabad WSS, which demonstrated higher siltation in the water source. One-way ANOVA analysis showed significant variations in pH, turbidity, TDS, K, Mg, PO₄, Cl, and SO₄ values, which revealed that these parameters differently contributed to the source water quality. Findings from this study suggested the implementation of proper corrosion prevention measures and the establishment of international collaboration for best corrosion practices, expertise, and developing standards.     

Modeling of Cr contamination in the agricultural lands of three villages near the leather industry in Kasur,Pakistan, using statistical and GIS techniques

Kasur is one of the hubs of leather industry in the Punjab, Pakistan, where chrome tanning method of leather processing is extensively being used. Chromium (Cr) accumulation levels in the irrigation water, soil, and seasonal vegetables were studied in three villages located in the vicinity of wastewater treatment plant and solid waste dumping site operated by the Kasur Tanneries Waste Management Agency (KTWMA). The data was interpreted using analysis of variance (ANOVA), clustering analysis (CA), and principal component analysis (PCA). Interpolated surface maps for Cr were generated using the actual data obtained for the 30 sampling sites in each of the three villages for irrigation water, soil, and seasonal vegetables. The level of contamination in the three villages was directly proportional to their distance from KTWMA wastewater treatment plant and the direction of water runoff. The highest level of Cr contamination in soil (mg kg^?1) was observed at Faqeeria Wala (37.67), intermediate at Dollay Wala (30.33), and the least in Maan (25.16). A gradational variation in Cr accumulation was observed in the three villages from contaminated wastewater having the least contamination level (2.02–4.40 mg L^?1), to soil (25.16–37.67 mg kg^?1), and ultimately in the seasonal vegetable crops (156.67–248.33 mg kg^?1) cultivated in the region, having the highest level of Cr contamination above the permissible limit. The model used not only predicted the current situation of Cr contamination in the three villages but also indicated the trend of magnification of Cr contamination from irrigation water to soil and to the base of the food chain. Among the multiple causes of Cr contamination of vegetables, soil irrigation with contaminated groundwater was observed to be the dominant one.     

Recycling polymeric waste from electronic and automotive sectors into value added products

The environmentally sustainable disposal and recycling of ever increasing volumes of electronic waste has become a global waste management issue. The addition of up to 25% polymeric waste PCBs (printed circuit boards) as fillers in polypropylene (PP) composites was partially successful: while the tensile modulus, flexural strength and flexural modulus of composites were enhanced, the tensile and impact strengths were found to decrease. As a lowering of impact strength can significantly limit the application of PP based composites, it is necessary to incorporate impact modifying polymers such as rubbery particles in the mix. We report on a novel investigation on the simultaneous utilization of electronic and automotive rubber waste as fillers in PP composites. These composites were prepared by using 25 wt.% polymeric PCB powder, up to 9% of ethylene propylene rubber (EPR), and PP: balance. The influence of EPR on the structural, thermal, mechanical and rheological properties of PP/PCB/ EPR composites was investigated. While the addition of EPR caused the nucleation of the β crystalline phase of PP, the onset temperature for thermal degradation was found to decrease by 8%. The tensile modulus and strength decreased by 16% and 19%, respectively; and the elongation at break increased by ~71%. The impact strength showed a maximum increase of ~18% at 7 wt.%–9 wt.% EPR content. Various rheological properties were found to be well within the range of processing limits. This novel eco-friendly approach could help utilize significant amounts of polymeric electronic and automotive waste for fabricating valuable polymer composites.

Open image in new window

     

Development of geomorphologic instantaneous unit hydrograph for a large watershed

Hill torrents cause a lot of environmental and property damage in Pakistan every year. Proper assessment of direct runoff in the form of hill torrents is essential for protection of environment, property, and human life. In this paper, direct surface runoff hydrograph (DSRH) was derived for a large catchment using the geomorphologic instantaneous unit hydrograph concept. The catchment with hill torrent flows in semi-arid region of Pakistan was selected for this study. It was divided into series of linear cascades and hydrologic parameters required for Nash's conceptual model, and were estimated using geomorphology of the basin. Geomorphologic parameters were derived from satellite images of the basin and ERDAS and ArcGIS were used for data processing. Computer program was developed to systematically estimate the dynamic velocity, its related parameters by optimization and thereby to simulate the DSRH. The data regarding rainfall-runoff and satellite images were collected from Punjab Irrigation and Power Department, Pakistan. Model calibration and validation was made for 15 rainfall-runoff events. Ten events were used for calibration and five for validation. Model efficiency was found to be more than 90% and root mean square error to be about 5%. Impact of variation in model parameters (shape parameter and storage coefficient) on DSRH was investigated. For shape parameter, the number of linear cascades varied from 1 to 3 and it was found that the shaper parameter value of 3 produced the best DSRH. Various values of storage coefficient were used and it was observed that the value determined from geomorphology and the dynamic velocity produced the best results.     

Monitoring of cotton dust and health risk assessment in small-scale weaving industry

The present study describes the estimation of particulate matter (cotton dust) with different sizes, i.e., PM(1.0), PM(2.5), PM(4.0), and PM(10.0 μm) in small-scale weaving industry (power looms) situated in district Hafizabad, Punjab, Pakistan, and the assessment of health problems of workers associated with these pollutants. A significant difference was found in PM(1.0), PM(2.5), PM(4.0), and PM(10.0) with reference to nine different sampling stations with p values <0.05. Multiple comparisons of particulate matter with respect to size, i.e. PM(1.0), PM(2.5), PM(4.0), and PM(10.0), depict that PM(1.0) differs significantly from PM(2.5), PM(4.0), and PM(10.0), with p values <0.05 and that PM(2.5) differs significantly from PM(1.0) and PM(10.0), with p values <0.05, whereas PM(2.5) differs non-significantly from PM(4.0), with a p value >0.05 in defined sampling stations on an average basis. Majority of the workers were facing several diseases due to interaction with particulate matter (cotton dust) during working hours. Flue, cough, eye, and skin infections were the most common diseases among workers caused by particulate matter (cotton dust).     

Determination of radioactive elements and heavy metals in sediments and soil from domestic water sources in northern peninsular Malaysia

Soil serves as a major reservoir for contaminants as it posseses an ability to bind various chemicals together. To safeguard the members of the public from an unwanted exposure, studies were conducted on the sediments and soil from water bodies that form the major sources of domestic water supply in northern peninsular Malaysia for their trace element concentration levels. Neutron Activation Analysis, using Nigeria Research Reactor-1 (NIRR-1) located at the Centre for Energy Research and Training, Zaria, Nigeria was employed as the analytical tool. The elements identified in major quantities include Na, K, and Fe while As, Br, Cr, U, Th, Eu, Cs, Co, La, Sm, Yb, Sc, Zn, Rb, Ba, Lu, Hf, Ta, and Sb were also identified in trace quantities. Gamma spectroscopy was also employed to analyze some soil samples from the same area. The results indicated safe levels in terms of the radium equivalent activity, external hazard index as well as the mean external exposure dose rates from the soil. The overall screening of the domestic water sources with relatively high heavy metals concentration values in sediments and high activity concentration values in soil is strongly recommended as their accumulation overtime as a consequence of leaching into the water may be of health concern to the members of the public.