Fully Bio-Sourced Nylon 11/Raw Lignin Composites: Thermal and Mechanical Performances

Ecofriendly fully bio-composites based on polyamide 11 (PA11) and lignin have been prepared on the entire concentration range using a twin-screw extruder. In this work, PA11 was blended with lignin by direct extrusion technology without any chemical pre- or in-situ- modifications or physical pretreatments. The presence of various organic and inorganic impurities in the selected technical lignin have been maintained. The incorporation of this cheap renewable material from biomass in bio-based PA11 was inspected by an array of characterization tools. Also, the effect of the presence of lignin on the morphology and on the mechanical properties of the resulting materials was examined. Finally, in-situ investigation of structural evolution in PA11 induced by the presence of lignin was analyzed by Fast Scanning Chip Calorimetry.     

Environmental Impact Assessment of Polylactide(PLA)/Chicken Feathers Biocomposite Materials

The aim of this study is to analyse the environmental impacts (EIs) of the process of preparation of new biocomposite materials obtained from polylactide (PLA) and chicken feathers (CFs). Two CFs stabilization methods and different percentages of CFs have been studied. The EIs of these new composites were compared to the impact of virgin PLA. Cradle-to-gate life cycle inventories were assessed for 0–35% v/v of CFs in a CFs/PLA biocomposite. Two CFs stabilization processes, autoclave and surfactant, were tested and compared with the aim to prioritize one of them from the environmental point of view. A composite plate of 184?×?184?×?2.2 mm³ was defined as the functional unit. Autoclave stabilization process exhibited lower environmental impact compared with surfactant stabilization process mainly due to both the lower requirements of electricity and water and the reduced pollution loads of the generated wastewater. Thus, the autoclave process was selected as the standard method when comparing the EIs of the proposed CFs/PLA biocomposites. In this sense, the addition of CFs to PLA matrix proportionally reduces all the EIs compared to pure PLA due to the replacement of PLA with CFs. This behaviour can be explained because the PLA production accounts for the 99% of the impact of the biocomposite. Consequently, CFs conveniently stabilized might be an alternative raw material to prepare CFs/PLA biocomposites with less environmental impact compared to pure PLA.     

The Synthesis and FTIR, Kinetics and TG/DTG/DTA Study of Inter Penetrating Polymer Networks (IPNs) Derived from Polyurethanes of Glycerol Modified Castor Oil and Cardanol Based Dyes

Interpenetrating polymer networks from agricultural products such as glycerol modified castor oil polyurethanes and cardanol based dyes have not been extensively studied so far. Such polymers were synthesized using benzoyl peroxide as initiator and ethylene glycol dimethacrylate as cross-linker. Characterizations of these polymers were performed by Fourier Transform infra red spectra and thermal analysis techniques such as thermogravimetric analysis, derivative thermogravimetry and differential thermal analysis. The kinetic parameters such as activation energies and orders of reaction were estimated by using Freeman?CAnderson??s method. The effects of changes in polyurethane to dye monomer weight ratio and NCO/OH molar ratio of polyurethanes on the properties of such polymers were studied.     

Chemical,physical and microbial properties and microbial diversity in manufactured soils produced from co-composting green waste and biosolids

The effects of adding biosolids to a green waste feedstock (100% green waste, 25% v/v biosolids or 50% biosolids) on the properties of composted products were investigated. Following initial composting, 20% soil or 20% fly ash/river sand mix was added to the composts as would be carried out commercially to produce manufactured soil. Temperatures during composting reached 50 °C, or above, for 23 days when biosolids were included as a composting feedstock but temperatures barely reached 40 °C when green waste alone was composted. Addition of biosolids to the feedstock increased total N, EC, extractable NH₄, NO₃ and P but lowered pH, macroporosity, water holding capacity, microbial biomass C and basal respiration in composts. Additions of soil or ash/sand to the composts greatly increased the available water holding capacity of the materials. Principal component analysis (PCA) of PCR-DGGE 16S rDNA amplicons separated bacterial communities according to addition of soil to the compost. For fungal ITS-RNA amplicons, PCA separated communities based on the addition of biosolids. Bacterial species richness and Shannon’s diversity index were greatest for composts where soil had been added but for fungal communities these parameters were greatest in the treatments where 50% biosolids had been included. These results were interpreted in relation to soil having an inoculation effect and biosolids having an acidifying effect thereby favouring a fungal community.     

City hazardous gas monitoring network

In our today's societies, many dangerous chemicals are produced and transported. Due to the vast use of chemicals, more chemical accidents are taking place with huge losses. In this study a city hazardous gas monitoring network was designed to detect the dispersion of toxic and combustible gases in the primary stages. The network could cover hazardous chemical facilities, important hazardous chemical routes, warehouses and special locations which may be the targets of terrorist attacks. The network is consisted of several local networks and a central control panel complex. Each local network has a local control panel in the center and many detectors and sounders around it at distances less than 3000 m that communicate with the local control panels wirelessly. In each location there are two types of gas detectors, toxic and combustible, and a sounder which are equipped with a wireless, radio frequency modem allowing the units to communicate readings and other information on a real-time basis with a remotely located local control panel. High sensitive Photo Ionization Detectors, PIDs, are used to provide fast and low-level on-site screening for chemicals contamination. Combustible gas detectors are the second choice to sense the combustible gas and verify the readings of PIDs in this regard. The central panel consists of several connected control panels work uniquely helping a computer set and the appropriate software and communicate with local control panels via telephone lines. All of the network components are shown on the monitor of central panel with special symbols by geographical information system program. The system is fully addressable so that the high level detection of a detector produces a blinking color double-circle around its symbol in GIS plan. In case of high level gas detection, a team of experts who are fully equipped with different portable detectors depart to the site to test the field to identify the chemicals. All readings of detectors are saved in a data bank and then analyzed to find any chemicals spills and leakages. The network was simulated by a special program so that the components of local networks and the central panel are shown in separate windows. By clicking on one detector on environmental window the formerly designed responses will be activated in central panel window.     

The crash severity impacts of fixed roadside objects

INTRODUCTION: This study analyzes the in-service performance of roadside hardware on the entire urban State Route system in Washington State by developing multivariate statistical models of injury severity in fixed-object crashes using discrete outcome theory. The objective is to provide deeper insight into significant factors that affect crash severities involving fixed roadside objects, through improved statistical efficiency along with disaggregate and multivariate analysis. METHOD: The developed models are multivariate nested logit models of injury severity and they are estimated with statistical efficiency using the method of full information maximum likelihood. RESULTS: The results show that leading ends of guardrails and bridge rails, along with large wooden poles (e.g. trees and utility poles) increase the probability of fatal injury. The face of guardrails is associated with a reduction in the probability of evident injury, and concrete barriers are shown to be associated with a higher probability of lower severities. Other variables included driver characteristics, which showed expected results, validating the model. For example, driving over the speed limit and driving under the influence of alcohol increase the probability of fatal accidents. Drivers that do not use seatbelts are associated with an increase in the probability of more severe injuries, even when an airbag is activated. IMPACT ON INDUSTRY: The presented models show the contribution of guardrail leading ends toward fatal injuries. It is therefore important to use well-designed leading ends and to upgrade badly performing leading ends on guardrails and bridges. The models also indicate the importance of protecting vehicles from crashes with rigid poles and tree stumps, as these are linked with greater severities and fatalities.     

The effects of parental altruism on the governance of family‐managed firms

We draw on the economic, corporate governance, and family business literatures to explain why the effects of family on family firms makes this governance form theoretically distinct from those of public and private non‐family firms. Our thesis is that parental altruism, when combined with private ownership and owner‐management, influences the ability of the firm's owner‐manager to exercise self‐control, which, in turn, can expose some family firms to conflicts rooted in the agency threats of moral hazard, hold‐up, and adverse selection. We then discuss why some other family firms are able to minimize these dark side threats and thereby attain altruism's brighter side. Finally, we discuss how altruism's influence changes over time as ownership becomes dispersed among family members and across generations. Copyright © 2005 John Wiley & Sons, Ltd.     

Investigation of potentially toxic heavy metals in different organic wastes used to fertilize market garden crops

The benefits of using organic waste as fertilizer and soil amendment should be assessed together with the environmental impacts due to the possible presence of heavy metals (HMs). This study involved analysing major element and HM contents in raw and size-fractionated organic wastes (17 sewage sludges and composts) from developed and developing countries. The overall HM concentration pattern showed an asymmetric distribution due to the presence of some wastes with extremely high concentrations. HM concentrations were correlated with the size of cities or farms where the wastes had been produced, and HM were differentiated with respect to their origins (geogenic: Cr–Ni; anthropogenic agricultural and urban: Cu–Zn; anthropogenic urban: Cd–Pb). Size fractionation highlighted Cd, Cu, Zn and Pb accumulation in fine size fractions, while Cr and Ni were accumulated in the coarsest. HM associations with major elements revealed inorganic (Al, Fe, etc.) bearing phases for Cr and Ni, and sulfur or phosphorus species for Cd, Cu Pb and Zn.     

Effect of water washing on the thermal behavior of rice straw

Rice straw can be used as a renewable fuel for heat and power generation. It is a viable mean of replacing fossil fuels and preventing pollution caused by open burning, especially in the areas where this residual biomass is generated. Nevertheless, the thermal conversion of rice straw can cause some operating problems such as slag formation, which negatively affects thermal conversion systems. So, the main objective of this research is studying the combustion behavior of rice straw samples collected from various regions by applying thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). In addition, the thermal behavior of ashes from rice straw was also analyzed in order to detect their melting points, and ash sintering was detected at different temperatures within the range between 550 and 1000 °C. Since washing rice straw with water could reduce the content of undesirable inorganic compounds related to the ash fusibility, samples of washed rice straw were analyzed under combustion conditions to investigate its differences regarding the thermal behavior of rice straw. The results showed that rice straw washing led to a significant improvement in its thermal behavior, since it reduced the ash contents and sintering formation.