A comparative study of biopolymers and alum in the separation and recovery of pulp fibres from paper mill effluent by flocculation

Recovery of cellulose fibres from paper mill effluent has been studied using common polysacchatides or biopolymers such as Guar gum, Xanthan gum and Locust bean gum as flocculent. Guar gum is commonly used in sizing paper and routinely used in paper making. The results have been compared with the performance of alum, which is a common coagulant and a key ingredient of the paper industry. Guar gum recovered about 3.86 mg/L of fibre and was most effective among the biopolyrners. Settling velocity distribution curves demonstrated that Guar gum was able to settle the fibres faster than the other biopolymers; however, alum displayed the highest particle removal rate than all the biopolymers at any of the settling velocities. Alum, Guar gum, Xanthan gum and Locust bean gum removed 97.46%, 94.68%, 92.39% and 92.46% turbidity of raw effluent at a settling velocity of 0.5 cm/min, respectively. The conditions for obtaining the lowest sludge volume index such as pH, dose and mixing speed were optimised for guar gum which was the most effective among the biopolymers. Response surface methodology was used to design all experiments, and an optimum operational setting was proposed. The test results indicate similar performance of alum and Guar gum in terms of fioc settling velocities and sludge volume index. Since Guar gum is a plant derived natural substance, it is environmentally benign and offers a green treatment option to the paper mills for pulp recycling.     

Investigation of physico-chemical properties and microbial community during poultry manure cocomposting process

Co-composting of poultry manure and rubber wood sawdust was performed with the ratio of 2:1 (V/V) for a period of 60 days. An investigation was carried out to study the extracellular enzymatic activities and structural degradation utilizing Fourier transform infrared spectroscopy (FT-IR), thermogravimetry and differential thermal analysis (TG/DTA) and scanning electron microscopy (SEM). The microbial succession was also determined by using denaturing gel gradient electrophoresis (DGGE). The compost was able to reach its highest temperature of 71 ℃ at day 3 and stabilized between 30 and 40 ℃ for 8 weeks. CMCase, FPase and β-glucosidase acted synergistically in order to degrade the cellulosic substrate. The xylanase activities increased gradually during the composting and reached the peak value of 11.637 U/g on day 35, followed by a sharp decline. Both LiP and MnP activities reached their peak values on day 35 with 0.431 and 0.132 U/g respectively. The FT-IR spectra revealed an increase in aromaticity and a decrease in aliphatic compounds such as carbohydrates as decomposition proceeded. TGA/DTG data exhibited significant changes in weight loss in compost samples, indicating degradation of organic matter. SEM micrographs showed higher amounts of parenchyma exposed on the surface of rubber wood sawdust at day 60, showing significant degradation. DGGE and 16S rDNA analyses showed that Burkholderia sp., Pandoraea sp., and Pseudomonas sp. were present throughout the composting process. Ornithinibacillus sp. and Castellaniella ginsengisoli were only found in the initial stage of the composting, while different strains of Burkholderia sp. also occurred in the later stage of composting.     

Assessing the life cycle study of alternative earth-retaining walls from an environmental and economic viewpoint

Environmental Science and Pollution Research - This research aims to assess the sustainability of the most common earth-retaining walls (Gravity Walls and Cantilever Walls) in terms of...     

The role of disinfectants and sanitizers during COVID-19 pandemic: advantages and deleterious effects on humans and the environment

Environmental Science and Pollution Research - Disinfectants and sanitizers are essential preventive agents against the coronavirus disease 2019 (COVID-19) pandemic; however, the pandemic crisis...     

Municipal solid waste management in Malaysia: Practices and challenges

Rapid economic development and population growth, inadequate infrastructure and expertise, and land scarcity make the management of municipal solid waste become one of Malaysia’s most critical environmental issues. The study is aimed at evaluating the generation, characteristics, and management of solid waste in Malaysia based on published information. In general, the per capita generation rate is about 0.5–0.8 kg/person/day in which domestic waste is the primary source. Currently, solid waste is managed by the Ministry of Housing and Local Government, with the participation of the private sector. A new institutional and legislation framework has been structured with the objectives to establish a holistic, integrated, and cost-effective solid waste management system, with an emphasis on environmental protection and public health. Therefore, the hierarchy of solid waste management has given the highest priority to source reduction through 3R, intermediate treatment and final disposal.     

Removal of ammoniacal nitrogen (N-NH3) from municipal solid waste leachate by using activated carbon and limestone.

The presence of ammoniacal nitrogen (N-NH3) in leachate is one of the problems normally faced by landfill operators. Slow leaching of wastes producing nitrogen and no significant mechanism for transformation of N-NH3 in the landfills causes a high concentration of ammoniacal nitrogen in leachate over a long period of time. A literature review showed that the removal of ammoniacal nitrogen from leachate was not well documented and to date, there were limited studies in Malaysia on this aspect, especially in adsorption treatment. The main objective of the present study was to investigate the suitability of activated carbon, limestone and a mixture of both materials as a filtering medium, in combination with other treatments capable of attenuating ammoniacal nitrogen which is present in significant quantity (between 429 and 1909 mg L(-1)) in one of the landfill sites in Malaysia. The results of the study show that about 40% of ammoniacal nitrogen with concentration of more than 1000 mg L(-1) could be removed either by activated carbon or a mixture of carbon with limestone at mixture ratio of 5:35. This result shows that limestone is potentially useful as a cost-effective medium to replace activated carbon for ammoniacal nitrogen removal at a considerably lower cost.     

The use of alum, ferric chloride and ferrous sulphate as coagulants in removing suspended solids, colour and COD from semi-aerobic landfill leachate at controlled pH.

Suspended solids, colour and chemical oxygen demand (COD) are among the main pollutants in landfill leachate. Application of physical or biological processes alone is normally not sufficient to remove these constituents, especially for leachate with a lower biochemical oxygen demand (BOD)/ COD ratio. The main objective of this research was to investigate the efficiency of coagulation and flocculation processes for removing suspended solids, colour and COD from leachate produced in a semi-aerobic landfill in Penang, Malaysia. A 12-month characterization study of the leachate indicated that it had a mean annual BOD/COD ratio of 0.15 and was partially stabilized, with little further biological degradation likely to occur. Particle size analysis of the raw leachate indicated that its 50th percentile (d50) was 11.68 microm. Three types of coagulants were examined in bench scale jar test studies: aluminium sulphate (alum), ferric chloride (FeCl3) and ferrous sulphate (FeSO4). The effects of agitation speed, settling time, pH, coagulant dosages and temperature were examined. At 300 rpm of rapid mixing, 50 rpm of slow mixing, and 60 min settling time, higher removals of suspended solids (over 95%), colour (90%) and COD (43%) were achieved at pH 4 and 12. FeCl3 was found to be superior to other coagulants tested. At pH 4 and 12, fair removal of suspended solids was observed at a reasonably low coagulant dose, i.e., 600 mg L(-1); hHowever, about 2500 mg L(-1) of coagulant was required to achieve good removals at pH 6. Better removals were achieved at higher temperature. The d50 of sludge after coagulation at pH 4 with a 2500 mg L(-1) FeCl3 dose was 60.16 microm, which indicated that the particles had been removed effectively from the leachate. The results indicate that coagulation and flocculation processes can be used effectively in integrated semi-aerobic leachate treatment systems, especially for removing suspended solids, colour and COD.     

Psychosocial safety climate: Conceptual distinctiveness and effect on job demands and worker psychological health

Psychosocial safety climate is an emerging construct that refers to shared perceptions regarding policies, practices, and procedures for the protection of worker psychological health and safety. The purpose of the research was to: (1) demonstrate that psychosocial safety climate is a construct distinct from related climate measures (i.e., physical safety climate, team psychological safety, and perceived organizational support); and (2) test the proposition that organizational psychosocial safety climate determines work conditions (i.e., job demands) and subsequently worker psychological health. We used samples from two different cultures; an Australian sample (N = 126 workers in 16 teams within a primary health care organization) and a Malaysian sample (N = 180 workers in 31 teams from different organizations and diverse industries). In both samples confirmatory factor analysis verified that psychosocial safety climate is a construct distinct from related climate measures. Using hierarchical linear modeling, psychosocial safety climate was superior to other team level climate measures in its negative relationship to both job demands and psychological health problems. Results supported a mediation process, psychosocial safety climate → job demands → psychological health problems, corroborating psychosocial safety climate as a preeminent stress risk factor, and an efficient target for intervention. We found both physical and psychosocial safety climates were stronger in the Australian, compared with the Malaysian work context. Levels of psychosocial safety climate were significantly lower than those of physical safety climate in both countries indicating a ‘universal’ lack of attention to workplace psychological health.     

At-risk behaviour analysis and improvement study in an academic laboratory

Academic laboratories contain inherently substantial risk conditions that students could expose to chemical and physical hazards. Procedures and guidelines related to laboratory safety are commonly available for students to adhere. However, many injuries and accidents or even fatalities are reported due to students’ violated safety practices while working in the laboratory. There was no reported proactive method or systematic technique to monitor and control students’ at-risk behaviour in the laboratory. This paper presented a program known as laboratory at-risk behaviour and improvement system (Lab-ARBAIS) to monitor and control students’ at-risk behaviours in the laboratory. Lab-ARBAIS used computer database for data acquisition and analysis on students’ at-risk behaviours observed. Pre-program questions on students’ at-risk behaviours that frequently violated safety regulations were utilized by observers to give observation feedback. The collected feedback was analysed and the results were posted in students’ portal to allow everyone to acknowledge their safety habits and practices. The routine observations and posted results are to instill a psychology effect in student’s habitual safety practices by reminding them on their frequently violated safety regulations. The implementation of the Lab-ARBAIS program to chemical engineering laboratory as a case study had shown a significant improvement on students’ frequent at-risk behaviours. The Lab-ARBAIS can easily be adopted in any academic laboratories to manage students’ at-risk behaviours to ensure safe work environment. With minor enhancement, the Lab-ARBAIS can easily be extended to be used in industrial laboratories.     

Using process stream index (PSI) to assess inherent safety level during preliminary design stage

In the current practice, safety assessment is conducted once the process design has been completed. At this stage of design, the freedom to change the conceptual design is very limited and whatever strategies to be implemented will only control the hazard. This paper reports on the development of inherent safety index known as a process stream index (PSI) for inherent safety level assessment at preliminary design stage from the perspective of an explosion. The aim for PSI is to calculate, compare and prioritize the level of inherent safety of process streams during simulation work that influences the explosion. By prioritizing the streams based on the potential for the explosion, the design engineers can easily identify the critical streams to be considered for improvement in order to avoid or minimize explosion hazards. An enhancement technique to reflect the contribution of the individual components in the mixture is introduced, which provide significant contribution to the ranking of inherent safety level of process streams. The assessment of inherent safety level using PSI is demonstrated by case studies of HYSYS simulation for Acrylic Acid Plant and Natural Gas Liquid (NGL) plant.