Modifications to an H2S Tape Sampler for Increasing Sensitivity and Accuracy in H2S Sampling

The tape samplers using lead acetate impregnated paper tapes for continuous hydrogen sulfide sampling are subject to a number of errors which can throw considerable doubt on the accuracy of H₂S concentrations being measured. Some of the errors have been minimized with a change in the humidification system and a reduction of the lamp intensity in the optical system.     

The Effect of Fuel Composition on Atmospheric Aerosol Due to Auto Exhaust

Aerosols attributable to automobile exhaust can be classified as two types—primary aerosol (initially present in the exhaust) and secondary aerosol (generated photochemically from hydrocarbons and nitrogen oxides in the exhaust). In this study, investigation was made of possible effects of motor-fuel composition on the formation of these aerosols. Secondary aerosol, of principal interest in this work, was produced by irradiating auto exhaust in Battelle-Columbus’ 610 ft³ environmental chamber. A limited number of determinations of primary aerosol in diluted auto exhaust was made at the exit of a 36 ft dilution runnel. Determination of both primary and secondary aerosol was based on light-scattering measurements.

Exhaust was generated with seven full-boiling motor gasolines, both leaded and nonleaded, in a 1967 Chevrolet which was not equipped with exhaust-emission control devices. Changes in fuel composition produced a maximum factor of three difference in light scattering due to primary aerosol. Aerosol yields, for consecutive driving cycles on the same fuel, vary considerably; as a result, ranking the fuels on the basis of average primary aerosol yield was not very meaningful. In addition to fuel composition, the more important independent variables are initial SO₂ concentration, relative humidity and initial hydrocarbon concentration. Statistical analysis of the data indicates that the seven test fuels can be divided into two arbitrary groups with regard to secondary aerosol-forming potential. The fuels in the lower light-scattering group had aromatic contents of 15 and 21%, while those in the higher light-scattering group had aromatic contents of 25, 48, and 55%. Although the fuels can be grouped on the basis of a compositional factor, the grouping of fuels with aromatic content ranging from 25 to 55% indicates that this compositional factor cannot be equated simply with aromatic content. In an associated study of the aerosol-forming potential of individual hydrocarbons prominent in auto exhaust, it was observed that aromatics produce substantially more photochemical aerosol than olefins and paraffins. However, experiments with binar/hydrocarbon mixtures containing aromatjcs, as well as in these exhaust experiments, a strong dependence of aerosol yield on the aromatic components is is not observed. Thus, the data indicate that the dependence of secondary aerosol formation on fuel factors is a complex one and cannot be predicted solely on the basis of a sirigle hydrocarbon component reactivity scale.

The two types of automobile aerosol did not have the same dependence on fuel, composition. The variation in total light scattering attributable to primary plus secondary aerosol was less than that due to either component alone. It therefore was concluded that the light scattering due to automobile exhaust emissions in these experiments was not significantly affected by changing fuel composition.     

On the Relation Between the Indoor and Outdoor Concentrations of Nitrogen Oxides

Simultaneous measurements were made of the concentrations of NO, NO₂, and CO inside and outside of a building. The building is located in the Los Angeles area, which is heavily polluted by photochemical smog, and the experiments were conducted at a time of the year when the pollutants in question tend to be high. The results shows that there is a direct relationship between the inside and outside concentrations, and that the phase lag between the concentrations depends principally on the ratio of the building volume to the ventilation rate. Although the outside concentrations of the pollutants in question did not follow the same pattern every day, peak concentrations seemed to be related to “rush-hour” traffic. By reducing ventilation rates during these periods, it may be possible to reduce the concentration peaks inside of the building. The building involved in the current study was not located in the immediate vicinity of heavy traffic, and the indoor concentrations of NO, NO₂, and CO did not appear to be very severe when compared to those defined by present air quality standards. Finally, the results support the belief that NO and O₃ do not co-exist indoors except in very small quantities.     

The Inhibition of Photochemical Smog I. Inhibition by Phenol,Benzaldehyde, and Aniline

In urban atmospheres hydrocarbons promote the conversion of NO to NO₂ under the influence of sunlight, ultimately giving rise to photochemical smog. The conversion results from a long chain process with HO radicals as the chain carrier. If this chain could be interrupted by suitable radical traps, the formation of photochemical smog would be inhibited. In this paper we report the results of studies using phenol, benzaldehyde, and aniline as inhibitors. Mixtures containing 16 mTorr C₃H₆, 8 mTorr NO, ～85 Torr 0₂, and the addi tives were irradiated at 25°C. The NO₂ pressure was monitored photometrically. In the absence of additive, the NO2 pressure first increases with irradiation time reaching a maximum conversion corresponding to 70% of the NO at 1 2 minutes. As the radiation time is lengthened, the NO₂ pressure drops. With the additive present, the formation of NO₂ is delayed. The time to reach the maximum percent conversion of NO to N0₂ becomes 20, 22, 31, and 40 minutes respectively, for 13 mTorr C₆H₅OH, 2 mTorr C₆H₅CHO, 8 mTorr C₆H₅CHO, and 4.1 mTorr C₆H₅NH₂ added. The problems and possibilities of adding inhibitors to the atmosphere to control air pollution are discussed.     

Fine Paniculate Removal and S02 Absorption with a Two Stage Wet Scrubber

This paper includes results from pilot plant studies and early field demonstration units and a discussion of the application of the limestone wet scrubbing process to a low sulfur syb-butuminous coal. This latter application required the development of a hybrid two stage scrubber to enable collection of the fine particulate matter as well as removal of a significant amount of the sulfur dioxide.     

Emissions into the Atmosphere Due to the Ceramic Salt Glazing Process

The techniques of Principal Component Analysis (PCA) and subsequent regression analysis were used in an attempt to describe local and upwind chemical and physical factors which affect the variability of SO₄ ^–2 concentrations observed in a rural area of the northeastern U.S. The data used in the analyses included upwind and local O₃ concentrations, temperature, relative humidity and other climatological information, SO₂, and meteorological information associated with backward trajectories. The investigation identified five principal components, three major (eigenvalues >1) and two minor (eigenvalues < one), which accounted for 52% (r = 0.72) of the variability in the SO₄ ^–2 regression model. These components can be described as representing local and upwind photochemistry, droplet growth, SO₂ emissions, and air mass characteristics. The study also indicated that in future studies it will be necessary to a priori select air pollution and meteorological variables for measurement to potentially increase the sensitivity of this type of receptor model.     

Pilot sample risk analysis for underground coal mine fires and explosions using MSHA citation data

After three decades of sustained continuous improvement of mine safety performances in the US, mine disasters in 2006 and 2007 compromised an excellent record and presented new challenges and vulnerabilities for the underground coal mining industry. In the aftermath of the incidents, formal investigations and new scrutiny of mine safety by the US Congress and expert study groups followed. The US Congress passed the Mine Improvement and New Emergency Response Act of 2006 (MINER Act), which mandated new laws to address the issues, including those related to mine fires and explosions from which miners must be protected. The National Mining Association-sponsored Mine Safety Technology and Training Commission report highlighted the role of risk analysis and management in identifying and controlling major hazards, such as fires and explosions. In this paper an approach is given for analyzing the risks for fires and explosions based on the Mine Safety and Health Administration citation database. Using 2006 citation data and focusing on subsystem failures, the methodology is applied to a database for a pilot sample of underground coal mines stratified by mine size and state.     

Nanofiltration of concentrated and salted tuna cooking juices

Tuna cooking juice from a Tunisian tuna-processing unit has a high level of polluting load: chemical oxygen demand (COD) is comprised between 4 and 20 g L⁻¹, nitrogen kjedahl (NK) between 0.6 and 3 g L⁻¹ and dry matter between 120 and 160 g L⁻¹. The juice has thus to be treated before being rejected into the environment. This paper considers the nanofiltration (NF) of these concentrated organic/inorganic mixtures using an AFC 30 (NF) membrane. The work focusses on the effect of organic and inorganic matters on the permeate flux and rejections of these matters. For this purpose, mixtures of salt and organic pollution (COD), used as model solutions, were prepared by the dilution of a typical industrial tuna cooking juice. The permeate flux was found to decrease when salt and organic matter concentrations increase. The recovery rate in organic matter decreases with increasing salt or organic matter content and the recovery rate of salt decreases when the COD concentration increases.     

Collective work and resilience of complex systems

This article aims to describe the characteristics of collective working situations in complex systems – especially those in nuclear power plants – related to common forms of cooperation, in order to improve systems resilience. In addition, we will try to detail some aspects of collective working situations, emphasizing the differences between various forms of control. The similarities between work activities (multi-addressed messages, linkage to regulation, central and peripheral information) are nonetheless exposed. We conclude by proposing a contribution to support systems design, thus facilitating cooperation in teamwork activities.     

Focus on mission success: Process safety for the Atychiphobist

Modern process plants are complex engineering systems. While thorough reviews of system safeguards are performed, catastrophic events continue to occur, often unfolding in unforeseen ways. Success in process safety demands safe processes, and understanding rare, high consequence events is central to the traditional process safety approach. This philosophy is common to all high-hazard industries, offering the potential for sharing approaches, experience, and lessons learned. The problem, however, is that people (and organizations and entire industries) who fear failure (atychiphobia) sometimes obsess about failure so much that they miss opportunities to succeed.This paper examines selected risk management practices in the power generation and aerospace industries and how those practices have led to improved performance. Risk informed decision making (RIDM) has had widespread application in the nuclear and aerospace industries, and is undergoing enhancements to become a key framework for risk management. Additionally, rather than focusing on avoidance of loss, there are emerging approaches supporting achievement of success. This approach provides a more direct link of risk to business and operational objectives, but does challenge conventional risk approaches founded in a loss prevention-centric view. The paper reflects upon risk informed decision making and success modeling, and suggests how these methods may be applied in the field of process safety. Specific examples are drawn from the defense in depth approach from the nuclear power industry and mission success concepts developed for NASA.