Zinc and cadmium accumulation and tolerance in populations of Sedum alfredii

To investigate the variation of Zn and Cd accumulation and tolerance of Sedum alfredii (a newly reported Zn/Cd hyperaccumulator), field surveys and hydroponic experiments were conducted among three populations of this species: two originating from old Pb/Zn mines in Zhejiang (ZJ) and Hunan (HN) Provinces and one from a "clean" site in Guangdong (GD) Province, China. Under field conditions, up to 12,524 and 12,253 mg kg(-1) Zn, and 1400 and 97 mg kg(-1) Cd in shoots of ZJ and HN plants were recorded respectively. Under hydroponic conditions, ZJ and HN plants accumulated significantly higher Zn and Cd in their leaves and stems, and possessed significantly higher Zn and Cd tolerance than GD plants. Among the two contaminated populations, ZJ plants showed higher Cd tolerance and accumulation (in leaves) than HN plants. The present results indicate that significant differences in Zn and Cd accumulation and tolerance exist in populations of S. alfredii.     

Geochemical assessment of metal concentrations in sediment core of Korangi Creek along Karachi Coast, Pakistan

Sediment core from Korangi Creek, one of the polluted coastal locations along the Karachi Coast Pakistan, was collected to trace the history of marine pollution and to determine the impact of industrial activity in the area. Down core variation of metals such as Ca, K, Mg, Al, S, Ti, V, Cr, Mn, Fe, Ni, Cu and Zn was studied in the 72.0 cm core. Nuclear analytical techniques, proton induced X-rays emission (PIXE), was employed to ascertain the chemical composition in sediment core. Grain size analysis and sediment composition of cored samples indicated that Korangi creek sediments are clayey in nature. Correlation matrix revealed a strong association of Ni, Cu, Cr and Zn with Fe and Mn. To infer anthropogenic input, enrichment factor (EF), degree of contamination and pollution load index were calculated. EF showed severe enrichment in surface sediment for Ni, Cu, Cr and Zn, indicating increased industrial effluents discharge in recent years. The study suggests that heavy metal discharge in the area should be regulated. If the present trend of enrichment is allowed to continue unabated, it is most likely that the local food web complexes in the creek might be at highest risk.     

Influence of Clear Fellings on the Bryophyte Component of the Broad-leaved Forests of the Bashkir Cis-Ural Region

The change in the composition of the bryophyte component of succession communities that occur in the process of natural regeneration at the site of clear felling of the indigenous elm—maple–linden forests of the Bashkir Cis-Ural Region has been studied. The vulnerability of species to the consequences of felling is affected by their substrate confinement, ecological amplitude in relation to the factors of temperature, humidity, variability of soil moisture, and type of life strategy. In the secondary aspen forests, the absence or low constancy of nemoral epiphytic and ground mosses was noted.     

Social justice and mobility in coastal Louisiana,USA

Regional Environmental Change - Louisiana faces extensive coastal land loss which threatens the livelihoods of marginalized populations. These groups have endured extreme disruptive events in the...     

Renewable energy sources: conflicts and opportunities in a changing landscape

Regional Environmental Change - Replacement of conventional energy sources with renewables such as solar panels and wind turbines requires adequate land. Impact assessments should be conducted to...     

Comparative Thermodynamic Study on the Contribution of the Autocondensation and Copolymerization Reactions for the Tannins of the Subspecies of Acacia nilotica

Autocondensation and copolymerization reactions of the Acacia nilotica subspecies tomentosa (Ant) and the subspecies adansonii (Ana) tannins extracts solutions have been studied at several pH values by thermomechanical analyzer. Results of chemical analysis of these tannins revealed that the studied tannins, Ant and Ana contained high percentages of extractable tannins (54 and 57 %) for and polyphenolic materials (78 and 80 %) respectively. Different hardeners such as paraformaldehyde, Urea and pMDI were added at different ratios and their polycondensation reactions was studied and compared with their autocondensation ones. The aim was to evaluate the tannins suitability for the production of commercially and technically viable tannin adhesives with reduced Formaldehyde emission for wood products and to study the interference between the autocondensation and the copolymerization reaction. The obtained results of autocondensation reaction for both of the tannins studied showed that the best Young’s modulus values for Ant (3,500 and 2,750 MPa) and Ana (2,650 and 2,620 MPa) were obtained at pH 5 and 7. The Young’s modulus values obtained by the tannins Ant were higher than those achieved by Ana. This indicates that the Ant is more reactive than Ana. These results were also in line with results achieved by the gel time for both of the tannins. Gel time results indicate that the reactivity of both tannins increased towards alkalinity with Ana being more reactive at alkaline pH. Addition of 8 % of paraformaldehyde was adversely affecting the autocondensation reactions, as the best Young’s modulus values were achieved at pH 4 for Ant tannins. As for Ana the higher Young’s modulus values (2,000 and 2,310 MPa) were achieved at pH 5 and 7. This indicates that autocondensation reaction was contributed to the final network of the copolymerization reaction. When smaller ratio of paraformaldehyde and Urea (5 %) was added to Ant tannins it favors the autocondensation reaction and the best Young’s modulus values were obtained at pH 5 and 7. Addition of pMDI (10–30 %) was found to decrease the temperature of copolymerization and the obtained Young’s modulus values by Ant were lower than those obtained by autocodensation reaction. Best Young’ modulus values were obtained by Ant at pH 5 and 7. Ana gave the best Young’s modulus values at pH 4 and 5 indicating that the autocondensation appears to depress the copolymerization reactions. The obtained results by both reactions were very important from technical and economical point of view as they concluded that it is very possible to produce adhesives system with zero emission depending on the tannins autocondensation reaction and pH values. Reduction of formaldehyde emission was also possible upon addition of smaller amount of paraformaldehyde and Urea.     

Gas-phase and semivolatile organic emissions from a modern nonroad diesel engine equipped with advanced aftertreatment

ABSTRACT

U.S. Tier 4 Final and Euro Stage IV and V regulations for nonroad compression-ignition engines have led to the development of exhaust aftertreatment technologies optimized for nonroad engines and duty cycles. In this study, several aftertreatment configurations consisting of state-of-the-art diesel oxidation catalysts (DOCs), diesel particulate filters (DPFs), copper (Cu) zeolite– and vanadium-based selective catalytic reduction (SCR) catalysts, and ammonia oxidation (AMOX) catalysts are evaluated using both nonroad transient (NRTC) and steady (8-mode NRSC) cycles in order to understand both component- and system-level effects of diesel aftertreatment on gas-phase, semivolatile, and particle-phase and particle-bound unregulated organic emissions. Organic emissions reported in this work include total hydrocarbon (THC), n-alkanes, branched alkanes, saturated cycloalkanes, aromatics, aldehydes, ketones, hopanes, steranes, and soluble organic fraction (SOF). Brake-specific emissions are reported for four configurations, including engine-out, DOC+CuZ-SCR+AMOX, V-SCR+AMOX, and DOC+DPF+CuZ-SCR+AMOX, and conversion of engine-out emissions is reported for the three aftertreatment configurations. Mechanisms responsible for the reduction of organic species are discussed in detail. This summary of emissions from a current nonroad diesel engine equipped with advanced aftertreatment can be used to more accurately model the impact of anthropogenic emissions on the atmosphere with tools such as the U.S. Environmental Protection Agency’s Motor Vehicle Emissions Simulator (MOVES2014a) model.

Implications: Anthropogenic emissions are a source of significant human health and environmental risk. This study, focused on the treatment of exhaust emissions from a modern nonroad diesel engine with a variety of aftertreatment configurations, examines the impact that human industrial activity can have on air pollution. In particular, we focus on the remediation of gas-phase and semivolatile organic emissions by emission reduction technologies. This detailed summary of emissions from a current nonroad diesel engine equipped with advanced aftertreatment can be used to more accurately model the impact of anthropogenic emissions on the atmosphere with tools such as the U.S. Environmental Protection Agency’s MOVES2014a model.     

Preparation and Characterization of Hydrogel Based on Poly(vinyl alcohol) Cross-Linked by Different Cross-Linkers Used to Dry Organic Solvents

Poly(vinyl alcohol) (PVA) hydrogels were chemically cross-linked with/without different cross-linkers such as glutaraldehyde and epichlorohydrin, in the presence of a catalyst, or activator (potassium hydroxide) to produce three types of hydrogels. The structures of PVA and the prepared gel types were determined by FTIR spectroscopy, the mechanical and thermal properties, of these hydrogels were examined. The effects of different pH values and temperatures on the swelling properties of the prepared gels were examined. From the obtained results, it was found that, the low concentration of the cross-linker produced hydrogel with moderate properties, but in absence of the cross-linker, the obtained hydrogel exhibited good properties and can be used as friendly environmentally moisture absorbents from the organic solvents. The insolubility and swelling properties of gels were tested in these solvents. The results indicated that these hydrogels can be used as moisture absorbents and solvent dryers.     

Why ozonolysis may not increase the hydrophilicity of particles

It is commonly assumed that atmospheric oxidation of hydrocarbon particles or hydrocarbon coatings on particles leads to polar products and increased water uptake, altering atmospheric visibility and increasing the likelihood they will act as cloud condensation nuclei (CCN). We show here through laboratory experiments that increased water uptake depends on the 3-dimensional structure of the particles. Laboratory studies of particles formed during ozonolysis of surface-bound alkenes, present as terminally unsaturated self-assembled monolayers (C8= SAM) on a silica substrate, were carried out at room temperature and 1 atm pressure. SAMs were exposed to ～10¹³ O₃ molecules cm^?3 for 40 min and resultant particles were analyzed using single particle Fourier transform infrared micro-spectroscopy (micro-FTIR) and secondary ion mass spectroscopy (SIMS). Spectroscopy results show that –COOH and other polar groups are formed but are buried inside a hydrophobic shell, consistent with earlier observations (McIntire et al., 2005, Moussa et al., 2009) that water uptake does not increase after reaction of the terminal alkene with O₃. These insights into the 3-D structure of particles formed on oxidation have important implications for the ability of secondary organic aerosols to act as CCN. In addition, the nature of the surface of the particles is expected to determine their uptake into biological systems such as the surface of the lungs.