Preparation of hydrophobic hierarchical pore carbon–silica composite and its adsorption performance toward volatile organic compounds

Carbon–silica materials with hierarchical pores consisting of micropores and mesopores were prepared by introducing nanocarbon microspheres derived from biomass sugar into silica gel channels in a hydrothermal environment.The physicochemical properties of the materials were characterized by nitrogen physical adsorption(BET),scanning electron microscopy(SEM),and thermogravimetric(TG),and the adsorption properties of various organic waste gases were investigated.The results showed that microporous carbon materials were introduced successfully into the silica gel channels,thus showing the high adsorption capacity of activated carbon in high humidity organic waste gas,and the high stability and mechanical strength of the silica gel.The dynamic adsorption behavior confirmed that the carbon–silica material had excellent adsorption capacity for different volatile organic compounds(VOCs).Furthermore,the carbon–silica material exhibited excellent desorption characteristics:adsorbed toluene was completely desorbed at 150℃,thereby showing superior regeneration characteristics.Both features were attributed to the formation of hierarchical pores.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

Hygroscopicity measurement of sodium carbonate, β-alanine and internally mixed β-alanine/Na2CO3 particles by ATR-FTIR

Water-uptakes of pure sodium carbonate(Na_2CO_3),pure β-alanine and internally mixedβ-alanine/Na_2CO_3 aerosol particles with different mole ratios are first monitored using attenuated total reflectance Fourier transform infrared spectroscopy(ATR-FTIR) technique.For pure Na_2CO_3 aerosol particles,combining the absorptions at 877 and 1422 cm-1 with abrupt water loss shows the efflorescence relative humidity(ERH) of 62.9%–51.9%.Upon humidifying,solid Na_2CO_3 firstly absorbs water to from Na_2CO_3·H2 O crystal at 72.0% RH and then deliquesces at 84.5% RH(DRH).As for pure β-alanine particles,the crystallization takes place in the range of 42.4%–33.2% RH and becomes droplets at ～ 88.2% RH.When β-alanine is mixed with Na_2CO_3 at various mole ratios,it shows no efflorescence of Na_2CO_3 whenβ-alanine to Na_2CO_3 mole ratio(OIR) is 2:1.For 1:1 and 1:2 β-alanine/Na_2CO_3 aerosols,the ERHs of Na_2CO_3 are 51.8%–42.3% and 57.1%–42.3%,respectively.While β-alanine crystal appears from 62.7% RH for 2:1 and 59.4% RH for both 1:1 and 1:2 particles and lasts to driest state.On hydration,the DRH is 44.7%–75.2% for Na_2CO_3 with the OIR of 1:1 and 44.7%–69.0%for 1:2 mixture,and those of β-alanine are 74.8% for 2:1 mixture and 68.9% for two others.After the first dehumidification–humidification,all the water contents decrease despite of constituent fraction.And at ～ 92% RH,the remaining water contents are 92%,89% and 82%at ～ 92% RH,corresponding to OIR of 2:1,1:1 and 1:2 mixed system,respectively.     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

不同浓度锌处理下水稻幼苗对镉的累积效应

为探究锌（Zn）对水稻镉（Cd）累积的影响及其根表铁膜所发挥的作用,选取Cd高累积型水稻品种中9优547（简称"Z547"）和Cd低累积型水稻品种金优402（简称"J402"）,采用温室水培试验,研究0、2、5、10、15和20 μmol/L等6个Zn浓度下水稻幼苗对Cd的累积效应,以及不同浓度Zn处理对根表铁膜生成量的影响.结果表明:①随着c（Zn）的增加,Z547和J402水稻幼苗生物量均呈先增后减的趋势,分别在c（Zn）为2和10 μmol/L时达到最大值.②Z547和J402水稻幼苗中w（Cd）均呈先降后增的趋势,分别在c（Zn）为5和2 μmol/L时达到最小值;当水稻幼苗中w（Cd）达到最小值时,Z547根和地上部中w（Cd）分别为31.65和11.47 mg/kg,J402根和地上部中w（Cd）分别为22.58和14.36 mg/kg.③不同浓度Zn处理下水稻幼苗各部位中w（Cd）均与根表铁膜中w（Mn）、w（Fe）、w（Fe+Mn）呈显著正相关,高铁膜处理水稻幼苗中w（Cd）显著高于低铁膜处理,表明根表铁膜生成量的增加会促进Cd在水稻幼苗中的累积.研究显示,当c（Zn）较低时,c（Zn）的增加会抑制水稻幼苗对Cd的累积;当c（Zn）较高时,c（Zn）的增加会促进水稻幼苗对Cd的累积,而Zn可通过控制根表铁膜的生成来影响水稻幼苗对Cd的累积.      

Metabolomic modulations in a freshwater microbial community exposed to the fungicide azoxystrobin

An effective broad-spectrum fungicide, azoxystrobin (AZ), has been widely detected in aquatic ecosystems, potentially affecting the growth of aquatic microorganisms. In the present study, the eukaryotic alga Monoraphidium sp. and the cyanobacterium Pseudanabaena sp. were exposed to AZ for 7 days. Our results showed that 0.2–0.5 mg/L concentrations of AZ slightly inhibited the growth of Monoraphidium sp. but stimulated Pseudanabaena sp. growth. Meanwhile, AZ treatment effectively increased the secretion of total organic carbon (TOC) in the culture media of the two species, and this phenomenon was also found in a freshwater microcosm experiment (containing the natural microbial community). We attempted to assess the effect of AZ on the function of aquatic microbial communities through metabolomic analysis and further explore the potential risks of this compound. The metabonomic profiles of the microcosm indicated that the most varied metabolites after AZ treatment were related to the citrate cycle (TCA), fatty acid biosynthesis and purine metabolism. We thereby inferred that the microbial community increased extracellular secretions by adjusting metabolic pathways, which might be a stress response to reduce AZ toxicity. Our results provide an important theoretical basis for further study of fungicide stress responses in aquatic microcosm microbial communities, as well as a good start for further explorations of AZ detoxification mechanisms, which will be valuable for the evaluation of AZ environmental risk.     

闽江河口养虾塘养殖期和非养殖期CO2通量变化特征

为揭示河口区陆基养虾塘从养殖期到非养殖期一年间的CO₂通量变化,以福建省闽江河口鳝鱼滩陆基养虾塘为研究对象,于2016年5月-2017年3月采用悬浮箱/静态箱-气相色谱法对养虾塘养殖期水-大气界面和非养殖期沉积物-大气界面白天CO₂垂直通量进行原位观测.结果表明:①养虾塘在整个研究期间CO₂通量变化范围为-62.87~162.81 mg/（m2·h）,平均值为（42.66±18.12）mg/（m2·h）,总体上表现为大气CO₂的释放源,且呈非养殖期CO₂通量平均值[（78.51±16.61）mg/（m2·h）]显著高于养殖期[（17.98±18.26）mg/（m2·h）]的特征.②养殖期间,养虾塘CO₂通量呈"排放-吸收"交替变化的特征,而非养殖期养虾塘一直是大气CO₂的净排放源.③养虾塘养殖期CO₂通量时间变化特征主要受到ρ（DOC）（DOC为总溶解有机碳）、ρ（SO₄2-）、ρ（Cl-）、盐度、pH、ρ（Chla）（Chla为叶绿素a）的影响,其中,pH和ρ（SO₄2-）是其主要影响因子,而ρ（TDN）（TDN为总溶解氮）、ρ（TDP）（TDP为总溶解磷）、ρ（SO₄2-）对非养殖期CO₂通量时间变化影响较大.研究显示,滨海陆基养殖塘是大气CO₂的重要来源,其排放通量多低于河流、水库等水生生态系统,但高于湖泊生态系统;养殖塘CO₂通量受人为影响明显,其较高的变异性与养殖生物、饲料投放以及浮游藻类有关.      

达里诺尔湖水体DOM荧光特征及其来源解析

达里诺尔湖（简称“达里湖”）是内蒙古自治区高原地区重要的生态屏障,探究达里湖水质状况及污染来源,对加强流域水环境治理、改善水环境质量具有十分重要的意义.于2018年9月及2019年6月对湖水进行采样,并通过三维荧光光谱结合PARAFAC（平行因子分析）模型,探究达里湖水体DOM（溶解性有机质）来源及其与水质的关系.结果表明:①达里湖水体中pH较高,ρ（DOC）（DOC为溶解性有机碳）、ρ（NH₄+-N）、ρ（TP）相对较高,均超过GB 3838—2002《地表水环境质量标准》Ⅴ类水质标准限值.②水体中DOM含4种荧光组分.夏季水体DOM主要分布于河流入湖口附近,其中,类腐殖质荧光组分（紫外区类富里酸和可见区类富里酸）占总组分的62.93%,类蛋白类荧光组分（类色氨酸和类酪氨酸）占总组分的36.07%;秋季水体DOM主要分布于东南侧,其中,类腐殖质荧光组分占总组分的40.52%,类蛋白类荧光组分占总组分的59.48%.③达里湖采样点荧光参数表明,达里湖DOM自生源特征较强,腐殖化程度较低.类腐殖质荧光组分与ρ（DOC）、ρ（Chla）均呈正相关,类色氨酸荧光组分与pH呈正相关,类络氨酸与ρ（DTN）、ρ（NH4+-N）、ρ（DTP）均呈正相关.研究显示,达里湖DOM具有陆源与生物源双重特性,DOM的形成与微生物、细菌、浮游生物的生命活动密切相关.      

不同制备温度下污泥生物炭对Cr(Ⅵ)的吸附特性

以城市剩余污泥为原料,于300,400,500,600 ℃温度条件下制备生物炭,通过单因素静态吸附实验探讨制备温度对生物炭吸附Cr（Ⅵ）的影响。结果表明:在500 ℃以内随着温度上升制备的生物炭对Cr（Ⅵ）的吸附量增加,制备温度高于500 ℃后变化不明显;扫描电镜（SEM）、比表面积（BET）、傅里叶红外光谱（FTIR）表征结果显示,热解温度对生物炭表面形貌和官能团组成有显著影响;等温模型及动力学拟合结果表明,生物炭吸附Cr（Ⅵ）为单分子层吸附、物理-化学复合吸附。热解温度对污泥制备生物炭吸附Cr（Ⅵ）的性能有显著影响,最佳制备温度为500 ℃,在此条件制备的生物炭对Cr（Ⅵ）的理论吸附量可达7.93 mg/g。     

内饰材料发射率对密封舱室热防护效率的影响

目的探究密封舱室热防护效率与其内饰材料表面发射率的关系,分析内饰材料发射率对其表面温度、舱室内温度的影响规律。方法采用自行设计的小型密封舱室和加热测量装置,对内饰材料表面及舱室内温度进行测量。结果当内饰材料发射率为0.09时,内饰表面温度为141.2℃,舱室内平均温度仅为90.8℃;内饰材料发射率为0.91时,内饰表面温度为124.4℃,舱室内平均温度为109.1℃。结论试样表面温度随材料发射率的提高而降低,舱室内部空气平均温度随材料发射率的提高而升高;试样表面温度与舱室空气平均温度的温度差随材料发射率的提高而减小;同时,相同试样表面温度与舱室平均温度的温度差随加热温度的提高而增加。