Automotive Exhaust Emission Levels by Geographic Area and Vehicle Make A Nationwide Survey

Gross average automotive exhaust emissions data collected by the Atlantic Richfield Clean Air Caravan during the summer of 1970 showed only slight geographical variations when the specific makes were ignored. When considering specific makes, significant differences were found on an average emissions basis. Vehicle population—emission distributions showed wide variations in the 50% population levels and in the percent of vehicles with emissions greater than specified values. Hydrocarbon (HC) and carbon monoxide (CO) data are given on a gross basis for the 1970, 1968-69, 1966-67, and pre-1966 model year group vehicles. Average HC and CO emissions and vehicle population-Idle emissions distribution curves are included for specific make vehicles in selected areas.     

Turbulent Plume in a Turbulent Cross Flow: Comparison of Wind Tunnel Tests with Field Observations

Plume rise downwind of a large stationary gas turbine was measured in the field and the conditions were then scaled in the laboratory. For the laboratory, the plume exit conditions, wind velocity and temperature profiles, and wind direction were matched. It was found that for high temperature exhaust, the buoyancy is best matched by calculating a dimensionless density difference. With properly calculated buoyancy length scales, the plume trajectories were compared and were found to agree quite well. The probability distributions of the entrainment constant and the average values of the entrapment constant with downwind distance were compared. The field data showed about 15% greater plume rise. The median entrainment constant was about 10% greater for the lab test and the shape of the probability distribution matched very closely.     

Workshop on Primary Sulfate Emissions

This article is a summary report on a workshop, Measurement Technology and Characterization of Primary Sulfur Oxides Emission from Combustion Sources, sponsored by the EPA Environmental Sciences Research Laboratory at Research Triangle Park, NC, held in Southern Pines, NC. The objectives of the workshop were: to review and discuss current measurement methods and problem areas for sulfur oxides emission with attention focused on sulfuric acid, sulfates, and sulfur-bearing particulate matter; to review and discuss emission data from various combustion sources operating under different conditions, which include various pollutant controls, fuel composition, excess boiler oxygen, etc.; to delineate and recommend areas in need of research and development effort. Scientists were invited to present the results of their studies on primary sulfate emissions. The 3-day workshop devoted one day to measurement technology, a second to characterization, and a third to critical assessment of the presented papers and development of summary working group reports on each half-day session of the initial 2 days. Thirty-one papers were presented by 29 participants on measurements and characterization. Four working group reports were developed and summarized in the last day. Highlights of the papers and reports are briefly reviewed. Workshop proceedings are available as an EPA publication.     

acid rain and environmental policy

Editor’s note: This paper by Dr. Jacobson was presented at the 74th annual meeting of the Air Pollution Control Association as part of a panel discussion entitled “Acid Rain–1981: An International Issue.” The session was held on June 22, 1981, and was arranged by APCA’s TT-6 Energy-Environmental Interactions Committee.     

Testing and Commercialization of Byproduct Dibasic cids as Buffer Additives for Limestone Flue Gas esulfurization Systems

Pilot plant (0.1 MW) tests and utility boiler full scale demonstration (194 MW) of byproduct organic dibasic acids (DBA) as buffer additives to limestone scrubbers have shown performance improvements equivalent to those achieved by the addition of pure adipic acid. Both SO₂ removal efficiency and limestone utilization increased, and no significant operating problems were observed with three of the four DBA tested. Chemical and biological evaluations of scrubber samples taken during the DBA testing indicated no detectable tOxicity or mutagenicity, and no significant environmental impact is expected as a result of DBA addition. Economic estimates indicate that substitution of DBA for pure adipic acid as a buffer additive will result in additive cost savings of 30 % or greater.     

Municipal solid waste generation in municipalities: quantifying impacts of household structure, commercial waste and domestic fuel

Waste management planning requires reliable data concerning waste generation, influencing factors on waste generation and forecasts of waste quantities based on facts. This paper aims at identifying and quantifying differences between different municipalities' municipal solid waste (MSW) collection quantities based on data from waste management and on socio-economic indicators. A large set of 116 indicators from 542 municipalities in the Province of Styria was investigated. The resulting regression model included municipal tax revenue per capita, household size and the percentage of buildings with solid fuel heating systems. The model explains 74.3% of the MSW variation and the model assumptions are met. Other factors such as tourism, home composting or age distribution of the population did not significantly improve the model. According to the model, 21% of MSW collected in Styria was commercial waste and 18% of the generated MSW was burned in domestic heating systems. While the percentage of commercial waste is consistent with literature data, practically no literature data are available for the quantity of MSW burned, which seems to be overestimated by the model. The resulting regression model was used as basis for a waste prognosis model (Beigl and Lebersorger, in preparation).     

Biodegradable Water Soluble Copolymer for Antimicrobial Applications

Synthesis and characterization of novel biodegradable, water soluble and optically active DL-malic acid (DMA) and citric acid (CA) copolymers were studied for possible use as antibacterial agents. The copolymers were synthesized by direct bulk melt condensation in the absence of a catalyst above 150 °C. Characterization of obtained copolymers was carried out with the help of infrared absorption spectra, differential scanning calorimetry and thermo gravimetric analysis. The antibacterial activity of copolymers against bacteria was investigated. The results obtained shows the above copolymers possess a broad wound dressing activity against different types of bacteria and may be useful as antibacterial agents.