Field evaluation of resistivity sensors for in situ moisture measurement in a bioreactor landfill

The ability of resistance-based sensors to measure in situ waste moisture content in a landfill was examined. One hundred and thirty-five resistance-based sensors were installed in a leachate recirculation well field at a bioreactor landfill in Florida, US. The performance of these sensors was studied for a period of over 6 years. The sensors were found to respond to an increase in moisture resulting from leachate recirculation. It was observed that 78% of sensors worked successfully in the field during the study period. The initial spatial average moisture content determined by the sensor readings (using a laboratory-derived calibration) was 42.8% compared to 23% from gravimetric readings. Eighteen sensors (13%) showed that they were saturated before liquid addition, and no change in moisture content was observed in these sensors during the study period. Laboratory-derived calibration methods resulted in an over-estimation of moisture content. An alternate field-calibration method, where wetted sensor output was assumed equal to the average of gravimetric measurements for wet samples, was evaluated. The final spatial average moisture contents were 64.2% and 44.4% for the laboratory-derived and field-derived calibration methodologies, respectively, compared to 45% measured gravimetrically from excavated waste samples. When moisture content was determined using a mass balance approach, the result was 34.6%. The results suggest that when appropriately calibrated, resistivity-based sensors can be used to obtain a reasonably accurate estimate of local moisture content. However, caution should be taken to extend the moisture content values that are representative of waste surrounding the sensors to estimate the overall moisture content on the landfill-wide scale.     

Aftermarket remanufacturing strategic planning decision-making framework: theory & practice

The authors of this paper offer an aftermarket, remanufacturing (or reman) decision-making framework (RDMF), developed, based on a comprehensive set of strategic factors (Subramoniam et al., 2009a) derived from an in-depth literature review and case studies. RDMF is also grounded on results from an industry survey and related theory. The survey targeted Original Equipment (OE) suppliers that are involved in automotive OE production and also provide remanufactured (or reman) parts for the aftermarket, which includes the Original Equipment Service (OES) and/or the Independent Aftermarket (IAM) business. A response rate of 42% was obtained for the survey; the respondents were business unit managers or chief engineers from 18 companies in the United States and Europe who are actively involved in the reman businesses. The survey results helped the authors of this paper to prioritize and confirm the strategic decision-making factors from previous research. The key factors considered to be important by more than 50% of the survey respondents, constituting roughly 79% of the strategic factors were then incorporated into RDMF. The RDMF will be useful for aftermarket supplier companies in general and in particular, will be useful for automotive suppliers, involved with OE and aftermarket production.     

Aero-lap polishing of poly crystalline diamond inserts using Multicon media

Increasing use of poly crystalline diamond (PCD) inserts as cutting tools and wear parts is vividly seen in automobile, aerospace, marine and precision engineering applications. The PCD inserts undergo series of manufacturing processes such as: grinding that forms the required shape and polishing that gives a fine finish. These operations are not straight forward as PCD is extremely resistant to grinding and polishing. Single crystal diamond can easily be polished by choosing a direction of easy abrasion, but polishing a PCD imposes serious difficulties as the grains are randomly oriented. Prior research on polishing of PCD inserts includes electro discharge grinding (EDG), dynamic friction polishing and grinding by a vitrified bonded diamond wheel. The surface textures of PCD produced using an EDG process often contains: micro cavities, particle pullout, micro-grooves, chipped edges, cracks and gouch marks. While applying the dynamic friction polishing method the PCD material undergoes phase transformation and hence increased polishing rate was apparently seen. However the phase transformation of PCD deteriorates the strength of the insert. Furthermore the inserts produced using the dynamic polishing method often exhibits cracks, chip off and edge damage while using as a cutting tool. Therefore, a new method “aero-lap polishing” was attempted as it applies controlled amount of impinging force by which the surface damage can be significantly reduced. The study did establish an improvement of surface finish of PCD from R_a = 0.55 μm, R_t = 4.5 μm to R_a = 0.29 μm, R_t = 1.6 μm within 15–25 min of polishing time along with significant reduction in surface defects.     

Formulation of a landfill pollution potential index to compare pollution potential of uncontrolled landfills

Generally speaking, landfilling is one of the prominent methods of waste disposal around the globe, but some under-developed and developing countries still continue to practice uncontrolled open dumping of waste. These uncontrolled landfills pose a relatively high threat to the various elements of the environment in comparison with the conventional engineered landfills that are used in many developed countries. However, some closed, un-engineered landfills do exist in developing countries. This paper presents a novel approach to compare the pollution potential of uncontrolled landfills using an index. The landfill pollution potential index (LPPI) has been developed using the Delphi technique and is an aggregation of six pollution indices that have already been developed for the quantification of different environmental elements. The LPPI is an increasing scale index, in which a higher index value indicates a higher pollution threat. The LPPI of a landfill in Delhi was calculated and the high LPPI value indicates that the respective landfill poses a significant threat to the environment. The LPPI can be used as an aid to diagnose a landfill's pollution potential relative to other landfills and therefore also to rank remediation investments.     

Effect of commercial pesticides on plant growth-promoting activities of Burkholderia sp. strain L2 isolated from rhizosphere of Lycopersicon esculentum cultivated in agricultural soil

The in vitro study was carried out to examine the toxicity of four commercially used pesticides (phorate, mancozeb, chlorpyrifos, and endosulfan) at the recommended dose (1X) and higher field doses (1.5X, 2X, 2.5X, and 3X) on plant growth-promoting activities of Burkholderia sp. strain L2, isolated from pesticide-treated rhizosphere of Lycopersicon esculentum. At the recommended dose, level of toxicity of all the pesticides to phosphate solubilization activity and indole-3-acetic acid (IAA) production was less detrimental as compared to exceeding doses. At maximum dose rate of each pesticide, the percentage decrease in phosphate solubilization and IAA production over control was found in order of chlorpyrifos < mancozeb < endosulfan < phorate. Present study proves that Burkholderia sp. strain L2 could be used as a potential microbial inoculant in the agricultural soil having persistent pesticide residues.