A novel passive water sampler for in situ sampling of antibiotics

Passive water sampling has several advantages over active methods; it provides time-integrated data, can save on time and cost compared to active methods, and yield high spatial resolution data through co-deployment of simple, cheap units. However, one problem with many sampler designs in current use is that their uptake rates for trace substances of interest are flow-rate dependent, thereby requiring calibration data and other information to enable water concentrations to be derived from the mass per sampler. However, the 'family' of samplers employing the principle of diffusive gradients in thin films (DGT) provides an in situ means of quantitatively measuring labile species in aquatic systems without field calibration. So far, this technique has only been tested and applied in inorganic substances: metals, radionuclides, nutrients, etc. Design and applications of DGT to trace organic contaminants ('o-DGT') would be of widespread interest. This study describes the laboratory testing and performance characteristics of o-DGT, with the antibiotic sulfamethoxazole (SMX) as a model compound and XAD18 as the novel binding agent. o-DGT uptake of SMX increased with time and decreased with diffusion layer thickness, confirming the principle for SMX. XAD18 showed sufficiently high capacity for SMX for routine field applications. o-DGT measurement of SMX was independent of pH (6-9) and ionic strength (0.001-0.1 M) and not affected by flow rate once above static conditions. The diffusion coefficient of SMX in the sampler was measured using an independent diffusion cell and information is presented to allow temperature correction and derivation of aqueous concentrations from deployed samplers. The potential use of o-DGT for in situ measurement of pharmaceutical antibiotics is confirmed by this study and applications are briefly discussed.     

Bioretention Design for Xeric Climates Based on Ecological Principles1

Abstract: Bioretention as sustainable urban stormwater management has gathered much recent attention, and implementation is expanding in mesic locations that receive more than 1,000 mm of annual precipitation. The arid southwestern United States is the fastest growing and most urbanized region in the country. Consequently, there is a need to establish design recommendations for bioretention to control stormwater from expanding urban development in this ecologically sensitive region. Therefore, we review the ecological limits and opportunities for designing bioretention in arid and semiarid regions. We incorporated USEPA Stormwater Management Model (SWMM) simulations to synthesize ecologically based design recommendations for bioretention in arid climates. From our review, an ideal bioretention garden area should be 6 to 8% of the contributing impervious drainage area (depending on region) with two layers of media, a 0.5‐m low‐nutrient topsoil layer above a 0.6‐m porous media layer that acts as temporary storage during a storm event. When planted with the suggested vegetation, this design maximizes stormwater treatment by promoting ecological treatment in the topsoil while promoting infiltration and evapotranspiration of stormwater by deep‐rooted shrubs that require no irrigation after establishment. This synthesis improves water resources management in arid and semiarid regions by introducing a sustainable bioretention design that protects local surface waters while reducing regional water demands for irrigation.     

Determining the native/non-native status of newly discovered terrestrial and freshwater species in Antarctica - current knowledge, methodology and management action

Continental Antarctic terrestrial and freshwater environments currently have few established non-native species compared to the sub-Antarctic islands and other terrestrial ecosystems on Earth. This is due to a unique combination of factors including Antarctica's remoteness, harsh climate, physical geography and brief history of human activity. However, recent increases in national operator and tourism activities increase the risk of non-native propagules reaching Antarctica, while climate change may make successful establishment more likely. The frequency and probability of human-assisted transfer mechanisms appear to far outweigh those of natural propagule introductions by wind, water, birds and marine mammals. A dilemma for scientists and environmental managers, which is exacerbated by a poor baseline knowledge of Antarctic biodiversity, is how to determine the native/non-native status of a newly discovered species which could be (a) a previously undiscovered long-term native species, (b) a recent natural colonist or (c) a human-mediated introduction. A correct diagnosis is crucial as the Protocol on Environmental Protection to the Antarctic Treaty dictates dramatically different management responses depending on native/non-native status: native species and recent natural colonists should be protected and conserved, while non-native introductions should be eradicated or controlled. We review current knowledge on how available evidence should be used to differentiate between native and non-native species, and discuss and recommend issues that should be considered by scientists and managers upon discovery of a species apparently new to the Antarctic region.     

Management of Large Wood in Streams: An Overview and Proposed Framework for Hazard Evaluation

Instream and floodplain wood can provide many benefits to river ecosystems, but can also create hazards for inhabitants, infrastructure, property, and recreational users in the river corridor. We propose a decision process for managing large wood, and particularly for assessing the relative benefits and hazards associated with individual wood pieces and with accumulations of wood. This process can be applied at varying levels of effort, from a relatively cursory visual assessment to more detailed numerical modeling. Decisions to retain, remove, or modify wood in a channel or on a floodplain are highly dependent on the specific context: the same piece of wood that might require removal in a highly urbanized setting may provide sufficient benefits to justify retention in a natural area or lower‐risk urban setting. The proposed decision process outlined here can be used by individuals with diverse technical backgrounds and in a range of urban to natural river reaches so that opportunities for wood retention or enhancement are increased.     

The Great Lakes Hydrography Dataset: Consistent,Binational Watersheds for the Laurentian Great Lakes Basin

Ecosystem‐based management of the Laurentian Great Lakes, which spans both the United States and Canada, is hampered by the lack of consistent binational watersheds for the entire Basin. Using comparable data sources and consistent methods, we developed spatially equivalent watershed boundaries for the binational extent of the Basin to create the Great Lakes Hydrography Dataset (GLHD). The GLHD consists of 5,589 watersheds for the entire Basin, covering a total area of approximately 547,967 km², or about twice the 247,003 km² surface water area of the Great Lakes. The GLHD improves upon existing watershed efforts by delineating watersheds for the entire Basin using consistent methods; enhancing the precision of watershed delineation using recently developed flow direction grids that have been hydrologically enforced and vetted by provincial and federal water resource agencies; and increasing the accuracy of watershed boundaries by enforcing embayments, delineating watersheds on islands, and delineating watersheds for all tributaries draining to connecting channels. In addition, the GLHD is packaged in a publically available geodatabase that includes synthetic stream networks, reach catchments, watershed boundaries, a broad set of attribute data for each tributary, and metadata documenting methodology. The GLHD provides a common set of watersheds and associated hydrography data for the Basin that will enhance binational efforts to protect and restore the Great Lakes.     

Ferric iron amendment increases Fe(III)-reducing microbial diversity and carbon oxidation in on-site wastewater systems

Onsite wastewater systems, or septic tanks, serve approximately 25% of the United States population; they are therefore a critical component of the total carbon balance for natural water bodies. Septic tanks operate under strictly anaerobic conditions, and fermentation is the dominant process driving carbon transformation. Nitrate, Fe(III), and sulfate reduction may be operating to a limited extent in any given septic tank. Electron acceptor amendments will increase carbon oxidation, but nitrate is toxic and sulfate generates corrosive sulfides, which may damage septic system infrastructure. Fe(III) reducing microorganisms transform all major classes of organic carbon that are dominant in septic wastewater: low molecular weight organic acids, carbohydrate monomers and polymers, and lipids. Fe(III) is not toxic, and the reduction product Fe(II) is minimally disruptive if the starting Fe(III) is added at 50–150 mg L^?1. We used ¹⁴C radiolabeled acetate, lactate, propionate, butyrate, glucose, starch, and oleic acid to demonstrate that short and long-term carbon oxidation is increased when different forms of Fe(III) are amended to septic wastewater. The rates of carbon mineralization to ¹⁴CO₂ increased 2–5 times (relative to unamended systems) in the presence of Fe(III). The extent of mineralization reached 90% for some carbon compounds when Fe(III) was present, compared to levels of 50–60% in the absence of Fe(III). ¹⁴CH₄ was not generated when Fe(III) was added, demonstrating that this strategy can limit methane emissions from septic systems. Amplified 16S rDNA restriction analysis indicated that unique Fe(III)-reducing microbial communities increased significantly in Fe(III)-amended incubations, with Fe(III)-reducers becoming the dominant microbial community in several incubations. The form of Fe(III) added had a significant impact on the rate and extent of mineralization; ferrihydrite and lepidocrocite were favored as solid phase Fe(III) and chelated Fe(III) (with nitrilotriacetic acid or EDTA) as soluble Fe(III) forms.     

A Comparison of Filter Types in the Collection and Gravimetric Determination of Airborne Particulate Matter Less than 2.5 Microns (PM25)

ABSTRACT

Five identical, collocated, low-volume samplers were operated to collect airborne particulate matter less than 2.5 microns (PM₂₅). Five commercially available filter types were installed in the samplers to compare the gravimetric determination of PM_2.5 concentrations in the atmosphere. The filters were rotated through the five samplers for two study periods—one in summer and one in winter. The study was performed in Sheridan, WY, in close proximity to a gravimetric laboratory to minimize the introduction of errors associated with sample handling. Rigorous quality assurance procedures were employed throughout the study.Four of the five filter types provided comparable gravimetric determinations of airborne PM_2.5.     

Comparison of Real-Time Instruments Used To Monitor Airborne Particulate Matter

ABSTRACT

Measurements collected using five real-time continuous airborne particle monitors were compared to measurements made using reference filter-based samplers at Bakers-field, CA, between December 2, 1998, and January 31, 1999. The purpose of this analysis was to evaluate the suitability of each instrument for use in a real-time continuous monitoring network designed to measure the mass of airborne particles with an aerodynamic diam less than 2.5 μm (PM_2.5) under wintertime conditions in the southern San Joaquin Valley. Measurements of airborne particulate mass made with a beta attenuation monitor (BAM), an integrating nephelometer, and a continuous aerosol mass monitor (CAMM) were found to correlate well with reference measurements made with a filter-based sampler. A Dusttrak aerosol sampler overestimated airborne particle concentrations by a factor of ~3 throughout the study. Measurements of airborne particulate matter made with a tapered element oscillating microbalance (TEOM) were found to be lower than the reference filter-based measurements by an amount approximately equal to the concentration of NH₄NO₃ observed to be present in the airborne particles. The performance of the Dusttrak sampler and the integrating nephelometer was affected by the size distribution of airborne particulate matter. The performance of the BAM, the integrating nephelometer, the CAMM, the Dusttrak sampler, and the TEOM was not strongly affected by temperature, relative humidity, wind speed, or wind direction within the range of conditions encountered in the current study. Based on instrument performance, the BAM, the integrating nephelometer, and the CAMM appear to be suitable candidates for deployment in a real-time continuous PM_2.5 monitoring network in central California for the range of winter conditions and aerosol composition encountered during the study.     

Accumulation of 14C-trinitrotoluene and related nonextractable (bound) residues in Eisenia fetida

To determine if trinitrotoluene (TNT) forms nonextractable residues in earthworms and to measure the relative degree of accumulation as compared to TNT and its deaminated metabolites, Eisenia fetida was exposed to ¹⁴C-TNT using dermal contact to filter paper or exposure to soil. Nonextractable residues made up 32-68% of total body burden depending on exposure media and depuration time. Parent TNT accounted for less than 3% of radioactivity, while ADNTs accounted for 7-38%. Elimination half-lives were 61-120 h for TNT, ADNTs, and DANTs, which was significantly lower than the half-lives found for nonextractable residues, 201-240 h. However, over 80% of the nonextractable residue was solubilized using weak acid (pH 2). Based on our findings that TNT accumulation occurs primarily as nonextractable residues, which have a longer half-life, and that nonextractable residues can be solubilized, we propose that nonextractable residues could be used as a selective biomarker for assessing TNT contamination.