Groundwater Remediation and Aquifer Clean-Up: A Case Study

Groundwater was being remediated with pump and treat technology at a facility where the groundwater was contaminated with commonly used degreaser solvents. Hydraulic conductivity of the heterogeneous residuum was beneficiated by applying pneumatic fracturing technology. The remedial system was controlled and monitored by a sophisticated remote telemetry system. A case history follows.     

On the thermal rupture of 1.9 m propane pressure vessels with defects in their thermal protection system

This paper describes the results from a series of fire tests that were carried out to measure the effect of defects in thermal protection systems on fire engulfed propane pressure vessels.

In North America thermal protection is used to protect dangerous goods rail tank-cars from accidental fire impingement. They are designed so that a tank-car will not rupture for 100 min in a defined engulfing fire, or 30 min in a defined torching fire. One common system includes a 13 mm blanket of high-temperature ceramic fibre thermal insulation covered with a 3 mm steel jacket. Recent inspections have shown that some tanks have significant defects in these thermal protection systems. This work was done to establish what levels of defect are acceptable from a safety standpoint.

The tests were conducted using 1890 l (500 US gallon) ASME code propane pressure vessels (commonly called tanks in the propane industry). The defects tested covered 8% and 15% of the tank surface. The tanks were 25% engulfed in a fire that simulated a hydrocarbon pool fire with an effective blackbody temperature of 870 °C.

The fire testing showed that even relatively small defects can result in tank rupture if the defect area is engulfed in a severe fire, and the defect area is not wetted by liquid from the inside. A wall failure prediction technique based on uniaxial high-temperature stress rupture test data has been developed and agrees well with the observed failure times.     

Calculating overpressure from BLEVE explosions

Although a certain number of authors have analyzed the prediction of boiling liquid expanding vapour explosion (BLEVE) and fireball effects, only very few of them have proposed methodologies for predicting the overpressure from such explosions. In this paper, the methods previously published are discussed and shown to introduce a significant overestimation due to the erroneous thermodynamic assumptions—ideal gas behaviour and isentropic vapour expansion—on which they are based (in fact, they give the maximum value of overpressure which can be caused by a BLEVE). A new approach is proposed, based on the—more realistic—assumption of an adiabatic and irreversible expansion process; the real properties of the substance involved in the explosion are used. The two methods are compared through the application to a given case.     

Modelling nitrogen fluxes at the landscape scale

The distribution and impacts of different nitrogen pollutants are inextricably linked. To understand the problem fully, the interactions between the different pollutants need to be taken into account. This is particularly important when it comes to abatement techniques, since measures to reduce emissions of one nitrogen pollutant can often lead to an increase in another. This project represents a step towards greater understanding of these issues by linking together new and existing nitrogen flux models into a larger framework. The modelling framework has been constructed and some of the nitrogen flows between fields, farms and the atmosphere have been modelled for a UK study area for typical farm management scenarios.     

Enzyme-Retted Flax Fiber and Recycled Polyethylene Composites

Municipal solid wastes generated each year contain potentially useful and recyclable materials for composites. Simultaneously, interest is high for the use of natural fibers, such as flax (Linum usitatissimum L.), in composites thus providing cost and environmental benefits. To investigate the utility of these materials, composites containing flax fibers with recycled high density polyethylene (HDPE) were created and compared with similar products made with wood pulp, glass, and carbon fibers. Flax was either enzyme- or dew-retted to observe composite property differences between diverse levels of enzyme formulations and retting techniques. Coupling agents would strengthen binding between fibers and HDPE but in this study fibers were not modified in anyway to observe mechanical property differences between natural fiber composites. Composites with flax fibers from various retting methods, i.e., dew- vs. enzyme-retting, behaved differently; dew-retted fiber composites resulted in both lower strength and percent elongation. The lowest level of enzyme-retting and the most economical process produces composites that do not appear to differ from the highest level of enzyme-retting. Flax fibers improved the modulus of elasticity over wood pulp and HDPE alone and were less dense than glass or carbon fiber composites. Likely, differences in surface properties of the various flax fibers, while poorly defined and requiring further research, caused various interactions with the resin that influenced composite properties.     

Mechanical and Barrier Properties of Biodegradable Films Made from Chitosan and Poly (Lactic Acid) Blends

Biodegradable film blends of chitosan with poly(lactic acid) (PLA) were prepared by solution mixing and film casting. The main goal of these blends is to improve the water vapor barrier of chitosan by blending it with a hydrophobic biodegradable polymer from renewable resources. Mechanical properties of obtained films were assessed by tensile test. Thermal properties, water barrier properties, and water sensitivity were studied by differential scanning calorimeter analysis, water vapor permeability measurements, and surface-angle contact tests, respectively. The incorporation of PLA to chitosan improved the water barrier properties and decreased the water sensitivity of chitosan film. However, the tensile strength and elastic modulus of chitosan decreased with the addition of PLA. Mechanical and thermal properties revealed that chitosan and PLA blends are incompatible, consistent with the results of Fourier transform infrared (FTIR) analysis that showed the absence of specific interaction between chitosan and PLA.     

Lightweight Concrete Containing an Alkaline Resistant Starch-Based Aquagel

Starch aquagel-based lightweight concrete has properties similar to those of other lightweight concrete products. However, starch aquagels are unstable in the strongly alkaline conditions typical of Portland Cement-based concrete and may interfere with the setting process. The effect of alkali treatments on the physical, mechanical, and functional properties of starch aquagels and aquagels from starch/polymer blends was investigated. Starch was blended at 100–115°C in a twin-screw extruder with five different polymers to determine whether the blends improved alkaline resistance. Polymer blends containing 5%, 15%, and 30% of the polymer hydrated and formed aquagels when equilibrated in water for 24 h. However, equilibrium moisture content was lower for the blends compared to the starch control. Aquagels equilibrated in 0.15 N NaOH swelled, lost compressive strength and had greater than 90% moisture. The blend of starch and 30% PVOH absorbed less moisture and was more resistant to alkaline dissolution in 1 N NaOH than the other blends tested making it a more suitable material for aquagel-based concrete. The moisture content of starch-based aquagels and mixing time were critical factors in determining setting times. The size of aquagel blends had a minor effect on density and compressive strength.