Polymers as Solid Waste in Municipal Landfills

Abstract

Synthetic polymers reach municipal landfills as components of products such as waste household paints, packaging films, storage containers, carpet fibers, and absorbent sanitary products. Some polymers in consumer products that reach landfills are designed to photodegrade or biodegrade. This article examines the significance of degradable polymers in management of solid waste in municipal landfills. Most landfills are not designed to photodegrade or biodegrade solid waste. Landfill disposal of stable polymers such as polyacrylics and polyethylenes is not associated with significant polymer degradation or mobility. Stability to photodegradation and biodegradation is an advantage when municipal landfills are used for disposal of polymer products as solid waste. Use of landfill disposal can be a responsible means to manage polymer waste and can be part of an overall waste management plan which includes source reduction, recycling, reuse, composting, and waste-to-energy incineration.     

Effectiveness of Smokeless Ashtrays

Abstract

Most environmental tobacco smoke (ETS) issues from the tips of smoldering cigarettes between puffs. Smokeless ashtrays are designed to reduce ETS exposure by removing particulate and/or gas-phase contaminants from this plume. This paper describes an experimental investigation of the effectiveness of four smokeless ashtrays: two commercial devices and two prototypes constructed by the authors. In the basic experimental protocol, one or more cigarettes was permitted to smolder in a room. Particulate or gas-phase pollutant concentrations were measured in the room air over time. Device effectiveness was determined by comparing pollutant concentrations with the device in use to those obtained with no control device. A lung deposition model was applied to further interpret device effectiveness for particle removal. The commercial ashtrays were found to be substantially ineffective in removing ETS particles because of the use of low-quality filter media and/or the failure to draw the smoke through the filter. A prototype ashtray using HEPA filter material achieved better than 90% particle removal efficiency. Gasphase pollutant removal was tested for only one prototype smokeless ashtray, which employed filters containing activated carbon and activated alumina. Removal efficiencies for the 18 gas-phase compounds measured (above the detection limit) were in the range of 70 to 95%.     

Unsteady Tall Stack Dispersion of Chimney Emissions and its Application to Varying Wind Directions

A procedure for calculating the concentration at any point and time under varying emissions and mean wind conditions is developed based on exact integration of the governing conservation equation. The procedure is simple, easy to use and has no numerical instability difficulties. Application of the procedure shows the fast achievement of steady state concentration under steady chimney emissions and mean wind conditions. It is also suggested that the procedure be used to calculate the correction factor to the time-averaged concentrations determined by conventional computer or physical modelling for constant wind condition to account for the actual fluctuating mean wind direction condition. If the wind databank does not contain detailed minute-to-minute data for exact calculation of the correction factor, the sinusoidal wind assumption should give good approximation without adversely affecting the margin of safety for environmental protection. It is also suggested that the meteorological data bank should contain information on hourly amplitude and standard deviations of wind directions if storage is insufficient to store minute-to-minute wind data.     

Ambient Air Benzene Concentrations in Canada (1989-1993): Seasonal and Day of Week Variations,Trends, and Source Influences

Abstract

Since 1987, the Pollution Measurement Division of the Environmental Protection Service, Environment Canada, has operated a field program for measuring benzene in ambient air. With the cooperation of provincial and municipal environmental agencies, samples have been collected at over 30 urban and rural monitoring sites across the country. Samples are collected in evacuated canisters and analyzed by gas chromatography with a mass-selective detector. Using data from all sites, the composite average benzene concentration for Canada over the years 1989 to 1993 was 3.6 μg/m³ and the composite median was found to be 2.6 μ/m³. Benzene concentrations are highest at urban sites near major streets and at sites influenced by industrial sources. For eighteen urban and suburban trend sites (those with no nearby industrial sources), composite annual median benzene concentrations decreased by 20% between 1989 and 1993. For the same period, median benzene concentrations decreased by 33% at four trend sites with nearby industries. At most monitoring sites the parameters for benzene and CO are highly correlated; supporting the inventory estimate that most emissions of benzene are due to vehicle exhaust. For sites with nearby industrial sources of benzene, the industries are estimated to account for 35 to 70% of the benzene dose experienced at the sites. These site specific contributions are much more significant than the estimated national emissions assigned to industrial sources.     

NOx Removal with Combined Selective Catalytic Reduction and Selective Noncatalytic Reduction: Pilot-Scale Test Results

Pilot-scale tests were conducted to develop a combined nitrogen oxide (NO_x) reduction technology using both selective catalytic reduction (SCR) and selective noncatalytic reduction (SNCR). A commercially available vanadium- and titanium-based composite honeycomb catalyst and enhanced urea (NH₂CONH₂) were used with a natural-gas-fired furnace at a NO_x concentration of 110 ppm. Changes in SNCR chemical injection temperature and stoichiometry led to varying levels of post-furnace ammonia (NH₃), which acts as the reductant feed to the downstream SCR catalyst. The urea-based chemical could routinely achieve SNCR plus SCR total NO_x reductions of 85 percent with less than 3 ppm NH₃ slip at reductant/NO_x stoichiometries ranging from about 1.5 to 2.5 and SCR space velocities of 18,000 to 32,000 h^?1. This pilot-scale research has shown that SNCR and SCR can be integrated to achieve high NO_x removal. SNCR provides high temperature reduction of NO_x followed by further removal of NO_x and minimization of NH₃ slip by a significantly downsized (high-space velocity) SCR.     

Effect of Moisture on the Pollutant Concentration Measurement

The effects of removing moisture from gaseous samples on the measurement of pollutant concentration were studied. Simple mathematical analysis was conducted to derive the formula for correcting the measured results. It was found that the error increases with increase in relative humidity or increase in temperature. The error may become significant under extreme conditions.     

Medical Waste Treatment and Disposal Methods Used by Hospitals in Oregon,Washington, and Idaho

ABSTRACT

This study investigated medical waste practices used by hospitals in Oregon, Washington, and Idaho, which includes the majority of hospitals in the U.S. Environmental Protection Agency's (EPA) Region 10. During the fall of 1993, 225 hospitals were surveyed with a response rate of 72.5%. The results reported here focus on infectious waste segregation practices, medical waste treatment and disposal practices, and the operating status of hospital incinerators in these three states. Hospitals were provided a definition of medical waste in the survey, but were queried about how they define infectious waste. The results implied that there was no consensus about which agency or organization's definition of infectious waste should be used in their waste management programs. Confusion around the definition of infectious waste may also have contributed to the finding that almost half of the hospitals are not segregating infectious waste from other medical waste. The most frequently used practice of treating and disposing of medical waste was the use of private haulers that transport medical waste to treatment facilities (61.5%). The next most frequently reported techniques were pouring into municipal sewage (46.6%), depositing in landfills (41.6%), and autoclaving (32.3%). Other methods adopted by hospitals included Electro-Thermal-Deac-tivation (ETD), hydropulping, microwaving, and grinding before pouring into the municipal sewer. Hospitals were asked to identify all methods they used in the treatment and disposal of medical waste. Percentages, therefore, add up to greater than 100% because the majority chose more than one method. Hospitals in Oregon and Washington used microwaving and ETD methods to treat medical waste, while those in Idaho did not. No hospitals in any of the states reported using irradiation as a treatment technique. Most hospitals in Oregon and Washington no longer operate their incinerators due to more stringent regulations regarding air pollution emissions. Hospitals in Idaho, however, were still operating incinerators in the absence of state regulations specific to these types of facilities.     

Evaluation of Dust Generated from Basic Oxygen Furnace Steel Making

Abstract

A detailed characterization has been made of the dust generated during steel making in basic oxygen furnaces (BOF). Chemical composition and particle size distribution have been analyzed. X-ray diffraction, scanning electron microscopy, and electron probe micro-analysis techniques have been used to identify the morphology and the nature of the major iron-bearing phases as well as the gangue constituents. The dust characteristics have been found to be widely different, depending on the type of process used in BOF steel making, namely, suppressed combustion or total combustion. The type of dust abatement system (dry or wet) additionally influences the nature of the gangue constituents. The possibility of utilizing the iron-bearing major phases has been examined.