Controlled Exposures of Volunteers to Respirable Carbon and Sulf uric Acid Aerosols

Respirable carbon or fly ash particles are suspected to increase the respiratory toxicity of coexisting acidic air pollutants, by concentrating acid on their surfaces and so delivering it efficiently to the lower respiratory tract. To investigate this issue, we exposed 15 healthy and 15 asthmatic volunteers in a controlled- environment chamber (21°C, 50 percent relative humidity) to four test atmospheres: (i) clean air; (ii) 0.5-μm H2SO4 aerosol at =100 μg/m³, generated from water solution; (iii) 0,5-μm carbon aerosol at =250 μg/m³, generated from highly pure carbon black with specific surface area comparable to ambient pollution particles; and (iv) carbon as in (iii) plus =100 μg/m³ of ultrafine H2SO4 aerosol generated from fuming sulfuric acid. Electron microscopy showed that nearly all acid in (iv) became attached to carbon particle surfaces, and that most particles remained in the sub-μm size range. Exposures were performed double-blind, 1 week apart. They lasted 1 hr each, with alternate 10-min periods of heavy exercise (ventilation =50 L/min) and rest. Subjects gargled citrus juice before exposure to suppress airway ammonia. Lung function and symptoms were measured pre-exposure, after initial exercise, and at endexposure. Bronchial reactivity to methacholine was measured after exposure. Statistical analyses tested for effects of H₂SO₄ or carbon, separate or interactive, on health measures. Group data showed no more than small equivocal effects of any exposure on any health measure. One individual's responses were consistent with a clinically significant excess airway constriction from H₂SO₄ plus carbon, and 2-3 others showed slight excess responses to the combined pollutants, but all these observations might have reflected chance variations. We conclude that coexisting carbon aerosol did not increase respiratory irritancy of H₂SO₄, in most healthy and asthmatic subjects exposed for 1 hr under simulated "worst-case" ambient conditions.     

Effect of Moisture on the Pollutant Concentration Measurement

The effects of removing moisture from gaseous samples on the measurement of pollutant concentration were studied. Simple mathematical analysis was conducted to derive the formula for correcting the measured results. It was found that the error increases with increase in relative humidity or increase in temperature. The error may become significant under extreme conditions.     

Moving Bed Adsorption System for Control of VOCs from an Aircraft Painting Facility

An activated carbon moving bed system (10 to 100 acf m air flow) was tested for controlling VOC emissions from a commercial aircraft painting facility. The cross-flow moving adsorbent bed showed a VOC collection efficiency in the 77.1 to 99.6 percent range over a superficial gas velocity range of 27 to 185 ft/min (0.14-0.94 m/sec). The collection efficiencies were neither affected by a change in carbon flow rates from 5 to 8 Ib/hr (2.3 to 3.6 kg/hr) nor by a change in the gas superficial velocity from 27 to 185 ft/min. The VOC concentration in the emission stream from the painting hangar was found to vary by at least a factor of 20 (from 0.18 to 15 ppm) both over the five month period (during which the 15 system tests of about three hours each were conducted) and within a single eight hour work shift.     

Comparative Study of Spray Booth Filter System Efficiency

ABSTRACT

During recent years, greater emphasis has been placed on the control of particulate emissions from painting operations. This has gained more importance as more is learned about the potential release of toxic metals to the atmosphere from painting operations. This has led to queries about the efficiency of various painting arrestor systems to reduce particulate discharges to the atmosphere. Even more important is the capability of the arrestor systems to control PM₁₀ emissions.

In 1995, the U.S. Environmental Protection Agency initiated a study to evaluate various dry paint overspray arrestor systems. This study was designed to evaluate not only the total emissions control capability of the arrestor but also the PM₁₀ control capability of the various system designs. Paint overspray arrestor systems using five different filtration concepts or materials were selected. They include systems constructed of fiberglass, paper, Styrofoam, and cardboard materials. These systems used filtration techniques incorporating the following filtration phenomena and designs: cyclone, baffle, bag systems, and mesh systems.

The testing used an optical particle counting procedure to determine the concentration of particles of a given size fraction to penetrate a test arrestor system. The results of the testing indicated that there are significant differences in the efficiency of the tested system designs to capture and retain PM₁₀.

This paper summarizes the results of the research conducted to determine the capability of the arrestor systems to capture particulate of sizes down to approximately 1 μm in surface diameter.     

Characterization of Municipal Solid Waste Incineration Residues From Facilities with Different Air Pollution Control Systems

Abstract

Municipal Solid Waste incinerator residues produced in two types of facilities were exhaustively characterized: granulometry, mineralogy, chemical composition, leaching behavior, and elemental distribution as a function of particle size. Air Pollution Control (APC) residues coming from a semi-dry scrubber have shown higher solubility than fly ashes originating in an Electrostatic Precipitator (ESP), as well as higher contents in volatile metals (Cd, Hg). Different metal speciation and distribution as a function of particle size have been found in fly ashes (ESP residues) and APC residues. In APC residues, heavy metals (with the exception of Hg) show a parabolic distribution with maxima in the smallest and largest particles, following the same profile as soluble salts. Metal distribution for APC residues exhibits that metals generally are not associated with silicate aluminate matrix. Results show the effect of adding lime to APC residues in metal speciation and distribution.     

Low Concentration Mercury Sorption Mechanisms and Control by Calcium-Based Sorbents: Application in Coal-Fired Processes

ABSTRACT

The capture of elemental mercury (Hg⁰) and mercuric chloride (HgCl₂) by three types of calcium (Ca)-based sor-bents was examined in this bench-scale study under conditions prevalent in coal-fired utilities. Ca-based sorbent performances were compared with that of an activated carbon. Hg⁰ capture of about 40% (nearly half that of the activated carbon) was achieved by two of the Ca-based sorbents. The presence of sulfur dioxide (SO₂) in the simulated coal combustion flue gas enhanced the Hg⁰ capture from about 10 to 40%. Increasing the temperature in the range of 65-100 °C also caused an increase in the Hg⁰ capture by the two Ca-based sorbents. Mercuric chloride (HgCl₂) capture exhibited a totally different pattern. The presence of SO₂ inhibited the HgCl₂ capture by Ca-based sorbents from about 25 to less than 10%. Increasing the temperature in the studied range also caused a decrease in HgCl₂ capture. Upon further pilot-scale confirmations, the results obtained in this bench-scale study can be used to design and manufacture more cost-effective mercury sorbents to replace conventional sorbents already in use in mercury control.     

Biological Removal of Gaseous Ammonia in Biofilters: Space Travel and Earth-Based Applications

ABSTRACT

Gaseous NH₃ removal was studied in laboratory-scale biofilters (14-L reactor volume) containing perlite inoculated with a nitrifying enrichment culture. These biofilters received 6 L/min of airflow with inlet NH₃ concentrations of 20 or 50 ppm, and removed more than 99.99% of the NH₃ for the period of operation (101, 102 days). Comparison between an active reactor and an autoclaved control indicated that NH₃ removal resulted from nitrification directly, as well as from enhanced absorption resulting from acidity produced by nitrification. Spatial distribution studies (20 ppm only) after 8 days of operation showed that nearly 95% of the NH₃ could be accounted for in the lower 25% of the biofilter matrix, proximate to the port of entry. Periodic analysis of the biofilter material (20 and 50 ppm) showed accumulation of the nitrification product NO₃ ^- early in the operation, but later both NO₂ ^- and NO₃ ^- accumulated. Additionally, the N-mass balance accountability dropped from near 100% early in the experiments to ~95 and 75% for the 20- and 50-ppm biofilters, respectively. A partial contributing factor to this drop in mass balance accountability was the production of NO and N₂O, which were detected in the biofilter exhaust.     

Comparison of Computer Simulations of Total Lung Deposition to Human Subject Data in Healthy Test Subjects

ABSTRACT

A mathematical model was used to predict the deposition fractions (DF) of PM within human lungs. Simulations using this computer model were previously validated with human subject data and were used as a control case. Human intersubject variation was accounted for by scaling the base lung morphology dimensions based on measured functional residual capacity (FRC) values. Simulations were performed for both controlled breathing (tidal volumes [V_T] of 500 and 1000 mL, respiratory times [T] from 2 to 8 sec) and spontaneous breathing conditions. Particle sizes ranged from 1 to 5 um. The deposition predicted from the computer model compared favorably with the experimental data. For example, when V_T = 1000 mL and T = 2 sec, the error was 1.5%. The errors were slightly higher for smaller tidal volumes. Because the computer model is deterministic (i.e., derived from first principles of physics), the model can be used to predict deposition fractions for a range of situations (i.e., for different ventilatory parameters and particle sizes) for which data are not available. Now that the model has been validated, it may be applied to risk assessment efforts to estimate the inhalation hazards of airborne pollutants.     

Construction and Economics of a Pilot/Full-Scale Biological Trickling Filter Reactor for the Removal of Volatile Organic Compounds from Polluted Air

ABSTRACT

The design and the construction of an actual 8.7-m³ pilot/ full-scale biotrickling filter for waste air treatment is described and compared with a previous conceptual scale-up of a laboratory reactor. The reactor construction costs are detailed and show that about one-half of the total reactor costs ($97,000 out of $178,000) was for personnel and engineering time, whereas ~20% was for monitoring and control equipment. A detailed treatment cost analysis demonstrated that, for an empty bed contact time of 90 sec, the overall treatment costs (including capital charges) were as low as $8.7/1000 m³ _air in the case where a nonchlorinated volatile organic compound (VOC) was treated, and $14/ 1000 m³ _air for chlorinated compounds such as CH₂Cl₂. Comparison of these costs with conventional air pollution control techniques demonstrates excellent perspectives for more field applications of biotrickling filters. As the specific costs of building and operating biotrickling filter reactors decrease with increasing size of the reactor, the cost benefit of biotrickling filtration is expected to increase for full technical-scale bioreactors.     

The 1999 Fresno Particulate Matter Exposure Studies: Comparison of Community,Outdoor, and Residential PM Mass Measurements

ABSTRACT

Two collaborative studies have been conducted by the U.S. Environmental Protection Agency (EPA) National Exposure Research Laboratory (NERL) and National Health and Environmental Effects Research Laboratory to determine personal exposures and physiological responses to par-ticulate matter (PM) of elderly persons living in a retirement facility in Fresno, CA. Measurements of PM and other criteria air pollutants were made inside selected individual residences within the retirement facility and at a central outdoor site on the premises. In addition, personal PM exposure monitoring was conducted for a subset of the participants, and ambient PM monitoring data were available for comparison from the NERL PM research monitoring platform in central Fresno. Both a winter (February 1-28, 1999) and a spring (April 19-May 16, 1999) study were completed so that seasonal effects could be