Study on the cytotoxicity of microcystin-LR on cultured cells

The toxicity of purified blue-green algal toxin, microcystin-LR, on permanent cell lines KB, NIH/3T3, H-4-II-E, HeLa, Vero, Hep G2, Caco-2 and HL-60 was studied. Assessment of cell viability using colorimetric 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assays indicated that purified microcystin-LR induced toxic effect on KB and H-4-II-E cell lines after 96 h incubation at toxin concentrations greater than 18.75 microg/ml. KB cell line was selected for further study when reproducibility, consistency and sensitivity were considered. Significant amounts of lactate dehydrogenase (LDH) were released from KB cells when incubation durations were 72 and 96 h with toxin concentrations of 18.75 microg/ml and higher. Although previous studies suggested that microcystin-LR had no cytotoxic effect on permanent cell lines, LDH release assay performed on KB cells indicated that exposure to microcystin-LR could result in damage to the cell membrane.     

Effects of tri-o-cresyl phosphate on serum estrogen and progesterone concentration and ATPase activity in the shell gland of adult hens

The activities of calcium-activated ATPase (Ca2+-ATPase) and calcium magnesium-activated ATPase (Ca2+-Mg2+-ATPase) in the shell gland, and concentrations of 17beta-estradiol (E2) and progesterone in serum were monitored, respectively, from hens orally dosed with tri-o-cresyl phosphate (TOCP) (750 mg/kg). Treated birds were monitored daily for laying and development of delayed neurotoxicity, and activities of Ca2+-ATPase and Ca2+-Mg2+-ATPase were measured at 7 and 10 days after dosing. TOCP-treated birds manifested motor deficit by 7-9 days postdosing, while hens administered vehicle exhibited no signs of delayed neurotoxicity. Ca2+-ATPase and Ca2+-Mg2+-ATPase activities of shell glands from TOCP-dosed hens were not significantly affected (P > 0.05). The serum E2 concentration was significantly reduced in TOCP-treated hens (P < 0.01); however, progesterone levels were unaffected.     

Monitoring, modelling and environmental exposure assessment of industrial chemicals in the aquatic environment

Monitoring and laboratory data play integral roles alongside fate and exposure models in comprehensive risk assessments. The principle in the European Union Technical Guidance Documents for risk assessment is that measured data may take precedence over model results but only after they are judged to be of adequate reliability and to be representative of the particular environmental compartments to which they are applied. In practice, laboratory and field data are used to provide parameters for the models, while monitoring data are used to validate the models' predictions. Thus, comprehensive risk assessments require the integration of laboratory and monitoring data with the model predictions. However, this interplay is often overlooked. Discrepancies between the results of models and monitoring should be investigated in terms of the representativeness of both. Certainly, in the context of the EU risk assessment of existing chemicals, the specific requirements for monitoring data have not been adequately addressed. The resources required for environmental monitoring, both in terms of manpower and equipment, can be very significant. The design of monitoring programmes to optimise the use of resources and the use of models as a cost-effective alternative are increasing in importance. Generic considerations and criteria for the design of new monitoring programmes to generate representative quality data for the aquatic compartment are outlined and the criteria for the use of existing data are discussed. In particular, there is a need to improve the accessibility to data sets, to standardise the data sets, to promote communication and harmonisation of programmes and to incorporate the flexibility to change monitoring protocols to amend the chemicals under investigation in line with changing needs and priorities.     

Vertical distribution of Cd, Pb and Zn in soils near smelters in the North of France

The analysis of the horizons of 12 soil profiles confirm occasionally significant levels of Cd, Pb and Zn contamination in the areas surrounding two lead and zinc smelters in the North of France. A pedological approach enabled the original Cd, Pb and Zn content of the horizons to be estimated, based on physico-chemical characteristics of soil unaffected by contamination. The main contamination was found in the upper 20-30 cm. Traces of Cd and Zn contamination were found at a depth of around 2 m. The mobility of the metals may be classified in the following order: Cd>Pb> or =Zn. The concentration profile of a metal seems insufficient to evaluate its movement as the metal could have been leached beyond the contaminated horizons. The depth reached by the metals increases with their concentration in the surface horizon; a decrease in pH and an increase in sand content seem to facilitate their movement. The depth reached by Zn increases with the organic carbon content in the surface horizon. Earthworm galleries act as paths via which metals migrate downwards     

In situ sequential treatment of a mixed contaminant plume

Groundwater plumes often contain a mixture of contaminants that cannot easily be remediated in situ using a single technology. The purpose of this research was to evaluate an in situ treatment sequence for the control of a mixed organic plume (chlorinated ethenes and petroleum hydrocarbons) within a Funnel-and-Gate. A shallow plume located in the unconfined aquifer at Alameda Point, CA, was found to contain up to 218,000 μg/l of cis-1,2 dichloroethene (cDCE), 16,000 μg/l of vinyl chloride (VC) and <1000 μg/l of 1,1 dichloroethene (1,1 DCE), trans-1,2 dichloroethene (trans-1,2 DCE) and trichloroethene (TCE). Total benzene, toluene, ethylbenzene and xylenes (BTEX) concentrations were <10,000 μg/l. Contaminated groundwater was funneled into a gate, 3.0 m wide, 4.5 m long and 6.0 m deep (keyed into the underlying aquitard) where treatment occurred. The initial gate segment consisted of granular iron, for the reductive dechlorination of the higher chlorinated ethenes. The second segment, the biosparge zone, promoted aerobic biodegradation of petroleum hydrocarbons and any remaining lesser-chlorinated compounds, stimulated by dissolved oxygen (DO) and carbon dioxide (CO₂) additions via an in situ sparge system (CO₂ was used to neutralize the high pH produced from reactions in the iron wall). Groundwater was drawn through the gate by pumping two wells located at the sealed, downgradient, end. Over a 4-month period an estimated 1350 g of cDCE flowed into the treatment gate and the iron wall removed 1230 g, or 91% of the mass. The influent mass of VC was 572 g and the iron wall removed 535 g, corresponding to 94% mass removal. The other chlorinated ethenes had significantly lower influent masses (3 to 108 g) and the iron wall removed the majority of the mass resulting in >96% mass removal for any of the compounds. In spite of these high removal percentages, laboratory column tests indicated that at these levels of chlorinated contaminants, surface saturation of the iron grains likely contributed to lower than expected reaction rates. In the biosparge zone, mass removal of cDCE appeared to occur predominantly by biodegradation (65%) with volatilization (35%) being an important secondary process. The dominant removal process for VC was volatilization (70%) although significant biodegradation was also indicated (30%). Laboratory microcosm results confirmed the potential for aerobic biodegradation of cDCE and VC. When average influent field concentrations for cDCE and VC were 220,000 and 46,000 μg/l, respectively, the sequential treatment unit removed 99.6% of the total mass and when the influent concentrations decreased to 26,000 and 19,000 μg/l for cDCE and VC, respectively, >99.9% removal within the treatment gate was attained. BTEX compounds were found to be significantly retarded in the iron treatment zone. Although they did eventually break through the granular iron, and into the gravel transition zone, none of these compounds was detected in the biosparge zone. No noticeable interferences between the anaerobic (reductive) and aerobic parts of the system occurred during testing. The results of this experiment show that in situ treatment sequences are viable, although further work is needed to optimize performance.     

Biospheric influence on carbon dioxide measurements in Italy

The study concerning carbon dioxide measurements taken during the 1997, 1998 and 1999 summer campaigns at two different altitude stations and biospheric conditions are presented. The higher station (Mt. Cimone, 2165 m a.s.l.) is characterised by 360° free horizon and is located on a rocky mountain while the lower (Ninfa lake, 1550 m a.s.l.) is located inside the red spruce and beech forest. The different behaviour of CO₂ at the two mountain stations has been registered. It shows the strong effect of nighttime soil emission and vegetation respiration on CO₂ mixing ratio increases and of diurnal vegetative activity on CO₂ concentration decreases at the lower measurement site. The baseline character of the higher measurement site has been confirmed by comparison of CO₂ diurnal amplitudes recorded at the two stations.     

Evidence for the contribution of methane in the formation of aromatics and soot in fuel-rich pre-mixed combustion

Experimental results from an isothermal laminar flow reactor at atmospheric pressure are presented on the chemical composition in the post-oxidative region of two sooting fuel-rich pre-mixed mixtures diluted in nitrogen. A base case composed of n-heptane and O2 in N2 at 1425 K with a C/O of 2.85 was perturbed by substituting 10% of the carbon in n-heptane with carbon as CH4. While these changes would intuitively reduce aromatics and soot formation by increasing H2 and decreasing C2H2 concentrations, we observe the opposite. The concentrations of individual aromatic species are observed to actually increase by up to 50% and the soot yield increases by 80%.     

Semiconductor-assisted photocatalytic degradation of reactive dyes in aqueous solution

This work reports the semiconductor-assisted photochemical degradation of reactive dyes. In an oxygenated-UV-ZnO system almost total decolorization of Remazol Brilliant Blue R, Remazol Black B, Reactive Blue 221 and Reactive Blue 222 was observed in reaction times of about 60 min. Extending the photochemical treatment up to 120 min, mineralization higher than 80% for all the dyes was observed. During the same period, the residual acute toxicity was significantly reduced only for Remazol Black B. A systematic optimization study carried out by factorial design showed that for the reactive dyes tested, the ZnO semiconductor exhibits a better efficiency than that observed with anatase TiO2. A synergistic effect in the coupled TiO2-ZnO system was not observed.