Waste polyvinylchloride derived pitch as a precursor to develop carbon fibers and activated carbon fibers

Polyvinylchloride (PVC) was successfully recycled through the solvent extraction from waste pipe with an extraction yield of ca. 86%. The extracted PVC was pyrolyzed by a two-stage process (260 and 410 degrees C) to obtain free-chlorine PVC based pitch through an effective removal of chlorine from PVC during the heat-treatment. As-prepared pitch (softening point: 220 degrees C) was spun, stabilized, carbonized into carbon fibers (CFs), and further activated into activated carbon fibers (ACFs) in a flow of CO2. As-prepared CFs show comparable mechanical properties to commercial CFs, whose maximum tensile strength and modulus are 862 MPa and 62 GPa, respectively. The resultant ACFs exhibit a high surface area of 1200 m2/g, narrow pore size distribution and a low oxygen content of 3%. The study provides an effective insight to recycle PVC from waste PVC and develop a carbon precursor for high performance carbon materials such as CFs and ACFs.     

Methane and carbon dioxide emission in a two-phase olive oil mill sludge windrow pile during composting

The aim of this work was to make some preliminary evaluations on CO(2) and CH(4) emissions during composting of two-phase olive oil mill sludge (OOMS). OOMS, olive tree leaves (OTL) and shredded olive tree branches (OTB) were used as feedstock for Pile I and Pile II with a 1:1:1 and 1:1:2v/v ratio, respectively. Each pile was originally 1.2m high, 2.0m wide and approximately 15.0m long. Four 500 ml volume glass funnels were inverted and introduced in each pile, two in the core (buried 50-60 cm from the surface) and two near the surface under a thin 10-15 cm layer of the mixture. Thin (0.5 cm diameter) plastic, 80 cm long tubes were connected to the funnels. A mobile gas analyser (GA2000) was used to measure the composition (by volume) of O2, CO2 and CH4 on a daily basis. The funnels were removed prior to each turning and reinserted afterwards. From each pair of funnels (core and surface) of both piles, one was kept closed between samplings. Two way ANOVA was used to test differences between piles and among the tubes. Post hoc Tukey tests were also used to further investigate these differences. There was a significant difference (at p<0.001) in the two piles for all three gases. The average concentrations of O2, CO2 and CH4 in Pile I, from all four funnels was 16.86%, 3.89% and 0.25%, respectively, where for Pile II the average values were 18.07%, 2.38% and 0.04%, respectively. The presence of OOMS in larger amounts in Pile I (resulting in more intense decomposing phenomena), and the larger particle size of OTB in Pile II (resulting in increasing porosity) are the probable causes of these significant differences. Samples from open funnels presented lower, but not significantly lower, O2 composition (higher for CO2 and CH4) in comparison with closed funnels in both depths and both piles. Not significant were also the different mean gas compositions between core and surface funnels in the same pile.     

Vanadium recovery from oil fly ash by leaching, precipitation and solvent extraction processes

In order to reduce the environmental impact due to land disposal of oil fly ash from power plants and to valorize this waste material, the removal of vanadium was investigated using leaching processes (acidic and alkaline treatments), followed by a second step of metal recovery from leachates involving either solvent extraction or selective precipitation. Despite a lower leaching efficiency (compared to sulfuric acid), sodium hydroxide was selected for vanadium leaching since it is more selective for vanadium (versus other transition metals). Precipitation was preferred to solvent extraction for the second step in the treatment since: (a) it is more selective; enabling complete recovery of vanadate from the leachate in the form of pure ammonium vanadate; and (b) stripping of the loaded organic phase (in the solvent extraction process) was not efficient. Precipitation was performed in a two-step procedure: (a) aluminum was first precipitated at pH 8; (b) then ammonium chloride was added at pH 5 to bring about vanadium precipitation.     

Effects of sewage sludge blending on the coal combustion: a thermogravimetric assessment

Combustion of urban sewage sludge together with coal in existing infrastructures may be a sustainable management option energetically interesting for these materials, usually considered wastes. Thermogravimetric analysis was used to study the combustion of a semianthracite coal and the modifications undergone when adding a small percentage (2%, 5%, 10%) of sewage sludge. Both Differential Scanning Calorimetric analysis and Differential Thermogravimetry burning profiles showed differences between coal and sewage sludge combustion. However, the effects of adding a percentage of sewage sludge equal or smaller than 10% was hardly noticeable in terms of heat release and weight loss during the coal combustion. This was further proved by non-isothermal kinetic analysis, which was used to evaluate the Arrhenius activation energy corresponding to the co-combustion of the blends. This work shows that thermogravimetric analysis may be used as an easy rapid tool to asses the co-combustion of sewage sludge together with coal.     

Biodegradability and ecotoxicity of amine oxide based surfactants

The aerobic and anaerobic biodegradability as well as the aquatic toxicity of two fatty amine oxides and one fatty amido amine oxide were investigated. Aerobic biodegradation was evaluated using the CO(2) headspace test (ISO 14593) and biodegradation under anaerobic conditions was assessed employing a standardised batch test. The three amine oxide based surfactants tested were readily biodegradable under aerobic conditions but only the alkyl amido amine oxide was found to be easily biodegradable under anaerobic conditions. Toxicity to Photobacterium phosphoreum and Daphnia magna was evaluated. Bacteria (EC(50) from 0.11 to 11 mg l(-1)) proved to be more sensitive to the toxic effects of the amine oxide based surfactants than crustacea (IC(50) from 6.8 to 45 mg l(-1)). The fatty amido amine oxide showed the lowest aquatic toxicity.     

Heavy metals in untreated/treated urban effluent and sludge from a biological wastewater treatment plant

Background, Aim and Scope

The presence of heavy metals in wastewater is one of the main causes of water and soil pollution. The aim of the present study was to investigate the removal of Cd, Cu, Pb, Hg, Mn, Cr and Zn in urban effluent by a biological wastewater treatment, as well as to quantify the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sn, Tl, V and Zn in dewatering sludge from the Biological Wastewater Treatment Plant to Ribeirão Preto (RP-BWTP), Brazil.

Materials and Methods

Concentrations of Cd, Cr, Cu, Mn and Pb in wastewater and those of Ni in sludge were determined by atomic absorption spectrophotometry with graphite furnace atomization. Mercury concentrations in wastewater were measured by hydride generation atomic spectrophotometry, and Zn levels were determined by atomic absorption spectrophotometry using acetylene flame. In sludge, the levels of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Pb, Sn, Tl, V and Zn were determined by inductively coupled plasma-mass spectrometry.

Results

The percentages of removal efficiency (RE) were the following: Hg 61.5%, Cd 60.0%, Zn 44.9%, Cu 44.2%, PB 39.7%, Cr 16,5% and Mn 10.4%. In turn, the mean concentrations (mg/kg) of metals in dewatering sludge followed this increasing order: Tl (<0.03), Hg (0.31), Be (0.43), As (1.14), Cd (1.34), V (59.2), Pb (132.1), Sn (166.1), Cr (195.0), Mn (208.1), Ni (239.4), Cu (391.7), Zn (864.4) and Fe (20537).

Discussion

The relationship between metal levels in untreated wastewater, as well as the removal efficiency are in agreement with previous data from various investigators, It is important to note that metal removal efficiency is not only affected by metal ion species and concentration, but also by other conditions such as operating parameters, physical, chemical, and biological factors.

Conclusions

Metal values recorded for treated wastewater and sludge were within the maximum permitted levels established by the Environmental Sanitation Company (CETESB), São Paulo, Brazil.

Recommendations

There is an urgent need for the authorities who are responsible for legislation on sludge uses in agriculture of establishing safety levels for As, Be, Hg, Sn, Tl and V.

Perspectives

According to the current metal levels, RP-BWTP sludge might be used for agriculture purposes. However, for an environmentally safe use of sewage sludge, further studies including systematic monitoring are recommended. Annual metal concentrations and predicted variations of those elements in the sludge should be monitored.

     

Community analysis in stream biomonitoring: what we measure and what we don't

Diatom assemblages from 83 epilithic samples taken from the Mesta River, Bulgaria, were regressed against three sets of predictor variables, i.e. environmental, spatial, and temporal. Redundancy analysis (RDA) of species and environmental data explained 36% of the diatom variance and extracted several important gradients of species distribution, associated with a downstream increase in nutrient levels, pH, temperature, and organic pollution. The inclusion of spatial and temporal variables in the RDA model captured additional 24% of the diatom variance and revealed three more gradients, a spatial gradient represented by higher order polynomial terms of latitude and longitude, and two temporal gradients of annual and seasonal variation. Partial RDAs demonstrated that the unique contribution of each predictor set to the explained diatom variance was the highest in the spatial dataset (16%), followed by the environmental (9%), and the temporal (7%) datasets. The remaining 28% of the variance was explained by the covariance of the predictor sets. This suggests that in biomonitoring of single stream basins, the cheap and simple account of space and time would explain most of the variance in assemblage composition obviating the necessity of expensive and time-consuming environmental assessments. The nature of the underlying environmental mechanisms can be easily inferred from the diatom composition itself.     

Size-related aspects of arm damage, tissue mechanics, and autotomy in the starfish Asterias rubens

 Arm damage is a widely reported but superficially investigated aspect of the biology of the starfish Asterias rubens L. In the present study, the incidence of arm damage was surveyed in populations of A.  rubens at two sites in the Firth of Clyde, Scotland, and three sites in Gullmarsfjorden, Sweden. The mean (±SD) incidence across all sites of individuals with basal arm damage (resulting from detachment at the basal autotomy plane) was 19.69 ± 8.86%, the incidence of those with distal arm damage (resulting from amputation at more distal levels) was 7.74 ± 10.01%. The mean incidence of arms with basal damage was 5.28 ± 4.12%, of those with distal damage 1.83 ± 2.45%. There was a significant negative correlation between size and the incidence of basal damage at all but one site, but no significant correlation between size and distal damage at any site. Mechanical tests on specimens of the aboral body wall from the basal region of the arm (which included the autotomy plane) and from a more distal region revealed that with increasing body size there was a significant increase in yield stress, ultimate stress and Young's modulus (stiffness) but no significant change in yield strain and ultimate strain. There was no significant difference between the relationships for basal and distal specimens. It is hypothesised that in larger individuals increased mechanical toughness replaces autotomy as an effective antipredator strategy. Using two methods to induce autotomy, a significant positive correlation between size and the delay between the onset of stimulation and arm detachment was found; this may represent a size-related decline in the efficiency of the autotomy mechanism through the relaxation of selection pressure. Since size is an unreliable indicator of age in A.  rubens, the trends identified herein can be interpreted only tentatively as age-associated phenomena. Received: 4 September 1999 / Accepted: 17 February 2000     

Effects of dissolved ammonium addition and host feeding with Artemia salina on photoacclimation of the hermatypic coral Stylophora pistillata

 Effects of nutrient treatments on photoacclimation of the hermatypic coral Stylophora pistillata (Esper) were studied. Studies on photoacclimation of colonies from different light regimes in the field were evaluated and used to design laboratory experiments. Coral colonies were collected in the Gulf of Eilat (Israel) from January to March 1993. Exterior branches of colonies from different depths (1 to 40 m) displayed different trends in production characteristics at reduced and very low levels of illumination. From 24 ± 3% to 12 ± 2% of incident surface photosynthetic active radiation (PAR_o), zooxanthella population density and chlorophyll a+c per 10⁶ zooxanthellae increased, a trend seen in the range of light levels optimal for coral growth (90 to 30% PAR_o). The P _max of CO₂ per 10⁶ zooxanthellae decreased, while P _max of CO₂ per 10³ polyps increased, indicating an increase in zooxanthella population density at low light levels. Proliferous zooxanthella frequency (PZF, a measure of zooxanthella division) declined significantly at light levels <18 ± 3% PAR_o. At the lowest levels of illumination (<5% PAR_o), zooxanthella population density decreased, as did the PZF; chl a+c per 10⁶ zooxanthellae was unchanged. In 28-d experiments, exterior coral branches from the upper surfaces of colonies from 3 m depth (65 ± 4% PAR_o) were incubated in aquaria under bright (80 to 90% PAR_o), reduced (20 to 30% PAR_o), and extremely low (2 to 4% PAR_o) light intensities. At each light intensity, the corals were maintained in three feeding treatments: sea water (SW); ammonium enriched SW (SW + N); SW with Artemia salina nauplii (SW + A). An increase in P _max of CO₂ per 10³ polyps was found in corals acclimated to reduced light (20 to 30% PAR_o) in nutrient-enriched SW, while in SW, where the increase in zooxanthella population density was smaller, it did not occur. Nutrient enrichments (SW + N at 2 to 4% PAR_o and SW + A at 20 to 30% PAR_o) increased zooxanthella population density, but had no effect on chl a+c per 10⁶ zooxanthellae. Acclimation for 14 d to reduced (10 to 20% PAR_o) and extremely low (1 to 3% PAR_o) light intensities shifted ¹⁴C photoassimilation into glycerol and other compounds (probably glycerides), rather than sugars. Both ammonium addition and feeding with Artemia salina nauplii resulted in an increase in photosynthetic assimilation of ¹⁴C into amino acids. We conclude that acclimation to reduced light consists of two processes: an increase in photosynthetic pigments and in zooxanthella population density. Both processes require nitrogen, the increase in zooxanthella population density needing more; this adaptation is therefore limited in nitrogen-poor sea water. Received: 19 June 1998 / Accepted: 13 June 2000     

Impact of continental margins in the Mediterranean Sea: Hints from the surface colour and temperature historical record

The surface colour and temperature fields of the Mediterranean Sea, as appearing in time series, of basin-wide images available in the CZCS (1979–1985) and AVHRR (1982–1991) historical archives, differentiate between basin interior and continental margins affected by coastal patterns, river plumes, and mesoscale features. The original data were processed to apply calibration factors, to correct for atmospheric contamination, and to estimate chlorophyll-like pigment concentration and surface temperature. Composites were derived, as monthly and annual means, using a fixed equal-area projection with a 1-km² pixel grid. Enhanced pigment values and lower temperatures along the northern coastal areas (i.e. the Ligurian, Provençal and Balearic basins, as well as the Adriatic, and Aegean Seas) have been associated with the impact of runoff from continental margins (i.e. both a direct impact due to the sediment load and one induced on the planktonic flora by the associated nutrient load) and with vertical mixing due to the prevailing winds (i.e. the Mistral in the northwest, the Bora in the Adriatic, the Etesians in the Aegean). The pattern of increasing pigments and decreasing temperatures in seen to develop in the monthly images from the coastal zone towards the open sea from summer to winter, and then back from winter to summer. The southern coastal areas show different values, namely lower pigments and higher temperatures (except in areas where the data are altered by signal contamination). It is suggested that differences in geomorphology and meteorology of the basin margins have an impact on both water biogeochemistry and dynamics, influencing the biooptical and thermal properties of the various sub-basins, and of the entire Mediterranean region.