Determining the ventilation and aerosol deposition rates from routine indoor-air measurements

Measurement of air exchange rate provides critical information in energy and indoor-air quality studies. Continuous measurement of ventilation rates is a rather costly exercise and requires specific instrumentation. In this work, an alternative methodology is proposed and tested, where the air exchange rate is calculated by utilizing indoor and outdoor routine measurements of a common pollutant such as SO₂, whereas the uncertainties induced in the calculations are analytically determined. The application of this methodology is demonstrated, for three residential microenvironments in Athens, Greece, and the results are also compared against ventilation rates calculated from differential pressure measurements. The calculated time resolved ventilation rates were applied to the mass balance equation to estimate the particle loss rate which was found to agree with literature values at an average of 0.50 h^?1. The proposed method was further evaluated by applying a mass balance numerical model for the calculation of the indoor aerosol number concentrations, using the previously calculated ventilation rate, the outdoor measured number concentrations and the particle loss rates as input values. The model results for the indoors’ concentrations were found to be compared well with the experimentally measured values.     

Co-occurrence profiles of trace elements in potable water systems: a case study

Potable water samples (N?=?74) from 19 zip code locations in a region of Greece were profiled for 13 trace elements composition using inductively coupled plasma mass spectrometry. The primary objective was to monitor the drinking water quality, while the primary focus was to find novel associations in trace elements occurrence that may further shed light on common links in their occurrence and fate in the pipe scales and corrosion products observed in urban drinking water distribution systems. Except for arsenic at two locations and in six samples, rest of the analyzed elements was below maximum contaminant levels, for which regulatory values are available. Further, we attempted to hierarchically cluster trace elements based on their covariances resulting in two groups; one with arsenic, antimony, zinc, cadmium, and copper and the second with the rest of the elements. The grouping trends were partially explained by elements’ similar chemical activities in water, underscoring their potential for co-accumulation and co-mobilization phenomena from pipe scales into finished water. Profiling patterns of trace elements in finished water could be indicative of their load on pipe scales and corrosion products, with a corresponding risk of episodic contaminant release. Speculation was made on the role of disinfectants and disinfection byproducts in mobilizing chemically similar trace elements of human health interest from pipe scales to tap water. It is warranted that further studies may eventually prove useful to water regulators from incorporating the acquired knowledge in the drinking water safety plans.     

Soil column experiments used as a means to assess transport,sorption, and biodegradation of pesticides in groundwater

Soil column experiments are used to investigate the fate of three pesticides of high, intermediate, and low solubility in groundwater: N- phosphonomethyl glycine (glyphosate); O,O-diethyl-S-[(ethylthio)methyl]phosphorodithioate (phorate); (2,4-dichlorophenoxy)acetic acid (2,4-D). Feed solutions are prepared by adding each pesticide (100 mg/L glyphosate, 50 μ g/L phorate, 50 mg/L 2,4-D) along with conservative tracer, KBr, in synthetic groundwater. The concentration of the pesticides in effluents is detected by ion chromatography (glyphosate, 2,4-D) and GC-FID (phorate). The Br^? breakthrough curves are employed to estimate the dispersion coefficient and mean pore velocity in each column. Solute transport and reactive models accounting for equilibrium/non-equilibrium sorption and biodegradation are coupled with inverse modeling numerical codes to estimate the kinetic parameters for all pesticides.     

Effectiveness of urea in enhancing the extractability of 2,4,6-trinitrotoluene from chemically variant soils

One of the major challenges in developing an effective phytoremediation technology for 2,4,6-trinitrotoluene (TNT) contaminated soils is limited plant uptake resulting from low solubility of TNT. The effectiveness of urea as a solubilizing agent in increasing plant uptake of TNT in hydroponic systems has been documented. Our preliminary greenhouse experiments using urea were also very promising, but further characterization of the performance of urea in highly-complex soil-solution was necessary. The present study investigated the natural retention capacity of four chemically variant soils and optimized the factors influencing the effectiveness of urea in enhancing TNT solubility in the soil solutions. Results show that the extent of TNT sorption and desorption varies with the soil properties, and is mainly dependent on soil organic matter (SOM) content. Hysteretic desorption of TNT in all tested soils suggests irreversible sorption of TNT and indicates the need of using an extractant to increase the release of TNT in soil solutions. Urea significantly (p < 0.0001) enhanced TNT extraction from all soils, by increasing its solubility at the solid/liquid interface. Soil organic matter content and urea application rates showed significant effects, whereas pH did not exert any significant effect on urea catalysis of TNT extraction from soil. The optimum urea application rates (125 or 350 mg kg⁻¹) for maximizing TNT extraction were within the limits set by the agronomic fertilizer-N rates used for major agricultural crops. The data obtained from this batch study will facilitate the optimization of a chemically-catalyzed phytoremediation model for cleaning up TNT-contaminated soils.     

Effective waste management with emphasis on circular economy

Environmental Science and Pollution Research -     

Agricultural and non-agricultural directions of bio-based sewage sludge valorization by chemical conditioning

Environmental Science and Pollution Research - This literature review outlines the most important—agricultural and non-agricultural—types of sewage sludge management. The potential of...     

Recycled tire granular for playground in hot regions: technical assessment

Journal of Material Cycles and Waste Management - Scrap tire granulation used for crumb rubber tiles and poured-in-place rubber surfaces are waste management strategy for the overgrowing tire...     

Modeling the emissions of a dual fuel engine coupled with a biomass gasifier—supplementing the Wiebe function

There is a growing market demand for small-scale biomass gasifiers that is driven by the economic incentives and the legislative framework. Small-scale gasifiers produce a gaseous fuel, commonly referred to as producer gas, with relatively low heating value. Thus, the most common energy conversion systems that are coupled with small-scale gasifiers are internal combustion engines. In order to increase the electrical efficiency, the operators choose dual fuel engines and mix the producer gas with diesel. The Wiebe function has been a valuable tool for assessing the efficiency of dual fuel internal combustion engines. This study introduces a thermodynamic model that works in parallel with the Wiebe function and calculates the emissions of the engines. This “vis-à-vis” approach takes into consideration the actual conditions inside the cylinders—as they are returned by the Wiebe function—and calculates the final thermodynamic equilibrium of the flue gases mixture. This approach aims to enhance the operation of the dual fuel internal combustion engines by identifying the optimal operating conditions and—at the same time—advance pollution control and minimize the environmental impact.     

NH4+-N versus pH and ORP versus NO3−-N sensors during online monitoring of an intermittently aerated and fed membrane bioreactor

Environmental Science and Pollution Research - Online sensors, which monitor the ammonia oxidation and the dissimilatory nitrate reduction process, can optimize aerobic and anoxic phase duration....     

Qualitative and quantitative determination of heavy metals in waste cellular phones

Twenty four waste cellular phones, manufactured between 2002 and 2011, were selected in order to determine the total heavy metal content in each of their parts (printed circuit boards (PCBs), plastic housing (PH) and liquid crystal display monitors (LCDs)) and compare the results with the permissible limits set by the 2003 Directive on Restriction of Hazardous Substances (RoHS). All the selected samples were pulverized and digested with strong acids. Inductively coupled plasma-mass spectrometry was used to measure the heavy metal content in each sample. The results revealed that concentration levels of the examined heavy metals were higher in PCBs, followed by PH and LCD in that particular order (PCB > PH > LCD). With the exception of Pb and Cr present in PCBs of mobile phones released before the year 2006, all the other metal concentrations were according to the Directive. Concentration levels of Cd, Hg were lower than the permissible limits set by the EU, either before or after the validity of the 2003 RoHS Directive. Considering their significant heavy metal content, coupled with their large quantities produced worldwide in an annual rate, waste cellular phones need to be treated under an environmentally sound management scheme, prioritizing recycling and at the same time eliminating the possibility of any harm.