企业社会资本研究

社会资本是指行动主体通过社会网络摄取稀缺资源并由此获益的能力.本文界定了企业社会资本的内涵、特征和功能,指出企业社会资本是企业建立在规范和信任基础上的,通过社会网络摄取稀缺资源的能力,它能够给企业带来收益,促进企业实现其目标.     

Fungicidal values of bio-oils and their lignin-rich fractions obtained from wood/bark fast pyrolysis

Pine wood, pine bark, oak wood and oak bark were pyrolyzed in an auger reactor. A total of 16 bio-oils or pyrolytic oils were generated at different temperatures and residence times. Two additional pine bio-oils were produced at the National Renewable Energy Laboratory in a fluidized-bed reactor at different temperatures. All these bio-oils were fractionated to obtain lignin-rich fractions which consist mainly of phenols and neutrals. The pyrolytic lignin-rich fractions were obtained by liquid-liquid extraction. Whole bio-oils and their lignin-rich fractions were studied as potential environmentally benign wood preservatives to replace metal-based CCA and copper systems that have raised environmental concerns. Each bio-oil and several lignin-rich fractions were tested for antifungal properties. Soil block tests were conducted using one brown-rot fungus (Gloeophyllum trabeum) and one white-rot fungus (Trametes versicolor). The lignin-rich fractions showed greater fungal inhibition than whole bio-oils for a impregnation solution 10% concentration level. Water repellence tests were also performed to study wood wafer swelling behavior before and after bio-oil and lignin-rich fraction treatments. In this case, bio-oil fractions did not exhibit higher water repellency than whole bio-oils. Comparison of raw bio-oils in soil block tests, with unleached wafers, at 10% and 25% bio-oil impregnation solution concentration levels showed excellent wood preservation properties at the 25% level. The good performance of raw bio-oils at higher loading levels suggests that fractionation to generate lignin-rich fractions is unnecessary. At this more effective 25% loading level in general, the raw bio-oils performed similarly. Prevention of leaching is critically important for both raw bio-oils and their fractions to provide decay resistance. Initial tests of a polymerization chemical to prevent leaching showed some success.     

钯离子液相催化氧化低浓度磷化氢

采用Pd^2＋液相催化氧化低浓度PH3,考察了Pd^2＋浓度、O2体积分数、PH3质量浓度、混合气流量、反应温度等因素对Pd^2＋吸收液去除低浓度PH3效果的影响。实验结果表明,采用10mL Pd^2＋浓度为0．112mol／L的水溶液作为吸收液净化含低浓度PH3的混合气,在反应温度22℃、O2体积分数5％、PH3质量浓度850mg／m^3、混合气流量190mL／min的条件下,印min之内PH3去除率保持在90％以上。Pd^2＋浓度越高、O2体积分数越大、反应温度越高,PH3去除率越高;混合气流量越大,PH3去除率越低;反应温度越低、O2体积分数越大,PH3去除率的下降速率越小。     

水体环境中氟喹诺酮类药物的污染现状及分析方法

阐述了水体环境中的氟喹诺酮类（FQs）药物的来源和污染现状,介绍了FQs在水体环境中的迁移、转化和转归途径,归纳了各种当前使用较多的FQs分析检测方法的功能特点和适用条件。指出今后在FQs分析技术的开发上,应注重提高检测容量、降低检出限和削减环境负面影响因素。     

铬渣解毒处理处置技术综述

简要介绍了国内外铬盐生产现状和铬渣堆存现状,对铬渣解毒处理处置技术的五大类方法进行了评述,着重对铬渣干法解毒处理处置技术进行了研究。分析了各方法的优缺点和存在的主要问题,提出了铬渣治理要求及今后的发展方向。     

硫酸生产中废钒催化剂回收工艺研究

采用H2SO4浸取、NH4HSO3还原、NH4NO3氧化、KOH精制的方法回收废钒催化剂中的V2O5。实验结果表明,还原反应的最佳条件为：n（NH4HSO3）／n（V2O5）=1．10,还原反应温度90℃,还原反应时间2．0h。氧化反应的最佳条件为：n（KOH）／n（VO^＋）=1．10,氧化反应温度60℃,液固比8,氧化反应时间60min。该方法V2O5回收率达90．3％以上,V2O5纯度达82％以上。     

在混合表面活性剂存在下锗和口底唑的胶束增溶分光光度法的研究

研究了以ＣＴＡＢ联用乳化剂ＯＰ,锗和口底唑的显色反应。结果表明,在ｐＨ５～６的酸度范围内及波长５０５ｎｍ处,络合物呈最大吸收,表观摩尔吸光系数为８１×１０４。用两种不同的方法研究了络合物的组成,组成比为Ｇｅ（Ⅳ）∶口底唑＝１∶３。本体系在０～１６０μｇＧｅ／２５ｍｌ范围内遵守比尔定律。本法使用混合掩蔽剂,提高了方法的选择性,并用于环境水样中锗的回收试验和阳极泥中锗的测定,得到了较好的结果     

建设项目竣工环境保护验收现状及建议

简述了当前建设项目竣工环境保护验收的现状,指出竣工环境保护验收存在权责不明、事中监管缺失、事后监管落地难、监测数据"失真"等问题,提出应落实建设单位的主体责任,规范建设项目竣工环境保护企业自行验收,加强事中、事后监管,整合建设单位监测数据,使验收监测数据发挥实效。     

GC-PID联用直接测定大气中痕量烃类化合物

作者把气相色谱仪(GC)与自行研制的光离子化检测器(PID)联用,实现了大气中痕量烃类化合物的直接测定,给出了仪器的构成和性能指标及测量结果.