干法腈纶生产废水脱氨氮研究

采用本实验室富集驯化的高效硝化细菌对生化处理后的干法腈纶生产废水进行了脱NH3-N研究,在连续运行装置中考察了DO和MLSS的变化特征,并研究了废水NH3-N负荷和COD负荷对脱NH3-N效果的影响.实验结果表明:该菌能适应干法腈纶生产废水中的难生物降解物质并有效去除废水中的NH3-N,启动期DO呈现"高-低-高"的变化,运行期污泥增长速率呈现"S"型变化;进水NH3-N负荷达到0.405 kg/(m3·d)时仍能维持出水P(NH3-N)在5 mg/L以下,进水COD负荷由0.126 kg/(m3·d)提高到0.975 kg/(m3·d)的过程中,NH3-N去除率始终高于96%.     

Biofiltration treatment of odors from municipal solid waste treatment plants

An in situ compost biofilter was established for the treatment of odors from biostabilization processing of municipal solid waste. The concentrations of total volatile organic compounds (VOCs) in odors and their components were measured. Biofilter media was characterized in terms of total carbon (TC), total nitrogen (TN), total phosphorus (TP), organic matter (OM), pH value and determination of bacterial colony structure. Gas chromatography–mass spectrometry (GC–MS) analysis showed that the main components of the produced gas were benzene, toluene, ethylbenzene and xylene (BTEX) along with other alkanes, alkenes, terpenes, and sulphur compounds. The compost biofilter had remarkable removal ability for alkylated benzenes (>80%), but poor removal for terpenes (～30%). Total VOC concentrations in odors during the biostabilization process period ranged from 0.7 to 87 ppmv, and the VOC removal efficiency of the biofilter varied from 20% to 95%. After about 140 days operation, TN, TC, TP and OM in compost were kept almost stable, but the dissolved N, NH₄–N and NO₃–N experienced an increase of 44.5%, 56.2% and 76.3%, respectively. Dissolved P decreased by 27.3%. The pH value experienced an increase in the early period and finally varied from 7.38 to 8.08. Results of bacterial colony in packing material indicated that bacteria and mold colony counts increased, but yeasts and actinomyces decreased along with biofilter operation, which were respectively, 3.7, 3.4, 0.04 and 0.07 times of their initial values.     

镰刀菌HJ01对对氯苯酚的降解特性

采用实验室分离的一株镰刀菌HJ01,以对氯苯酚(4-CP)为降解底物,以蔗糖为外加碳源,考察了蔗糖质量浓度、降解温度、初始pH对4-CP降解效果的影响,初步探讨了镰刀菌HJ01对4-CP的降解动力学和降解机理.实验结果表明:该菌株能以4-CP为惟一碳源和能源生长;在外加蔗糖为碳源,蔗糖质量浓度为3 g/L、降解温度为30℃、初始pH为8的条件下,50 mg/L4-CP能在6 d内被完全降解.以4-CP为惟一碳源和外加蔗糖下的降解动力学分别符合Haldane模型和一级动力学方程.     

混凝法深度处理印染废水中试研究

采用"高效混凝沉淀-过滤"深度处理工艺处理印染废水二级生化出水,并将混凝沉淀污泥回流.实验结果表明,混凝剂聚合氯化铝加入量为160 mg/L时,COD去除率平均可达34.6%,TP去除率平均达到87.9%,平均出水TP为0.3 mg/L.气相色谱-质谱分析和元素分析结果表明混凝沉淀工艺对有机物和TP的去除效果良好.     

废聚碳酸酯水解法制双酚A

以1,4-二氧六环为溶剂、NaOH为催化剂,采用废聚碳酸酯(PC)常压水解法制双酚A(BPA).对反应影响因素进行了研究.实验结果表明,在反应温度为100℃、反应时间为8h、m(NaOH):m(水+溶剂)=1:33、m(溶剂):m(PC)=4:1、m(水):m(PC)=1:1的最佳反应条件下,PC水解率大于98%,BPA收率大于95%.     

利用含铬废水和含铅废水制备铬黄

利用净化后的含铬废水和含铅废水制备铬黄.采用沉淀法对废水进行净化预处理,最佳工艺条件:100mL含铬废水中加入20 g Na_2CO_3,及10 mL H_2O_2,用NaOH调节含铬废水pH为10.00;用NaOH调节含铅废水pH为2.65.将净化后的10 mL含铬废水和25 mL含铅废水混合,在55-60℃条件下反应10 min,合成的铬黄达到GB/T 3184-2008<铬酸铅颜料和钼铬酸铅颜料>的质量标准.经重金属吸附剂处理Pb~(2+)后铬黄合成滤液中的Cr~(6+)和Pb~(2+)质量浓度均达到GB8978-1996<污水综合排放标准>的指标.     

N掺杂TiO_2光催化剂的制备及其H_2O_2改性的研究

以钛酸四丁酯为前驱物,采用水解沉淀法制备了N掺杂TiO_2光催化剂和H_2O_2改性的N掺杂TiO_2光催化剂.实验表明,H_2O_2改性的N掺杂TiO_2光催化剂的最佳制备条件为:氨水(质量分数28%)加入量20 mL,焙烧温度500 ℃,H_2O_2(质量分数30%)加入量2.0 mL.日光下,N掺杂TiO_2光催化剂及H_2O_2改性的N掺杂TiO_2光催化剂在反应90 min时的活性红紫去除率达99%,它们对活性红紫的去除率远高于P_(25)TiO_2光催化剂.H_2O_2改性的N掺杂TiO_2光催化剂中N质量分数比改性前明显提高,制备的两种催化剂中不仅含有N元素,同时还含有C和H元素.     

硫酸渣制备高纯度硫酸亚铁

以高铁硫酸渣为原料,采用酸浸一还原-除杂-结晶-重结晶-干燥工艺,合成高纯度硫酸亚铁.通过反应温度、反应时闻对硫酸渣中铁的浸出率的影响,以及结晶温度、干燥温度,干燥时间、于燥时间对硫酸亚铁产品纯度的影响做分析实验,得出最佳酸浸条件:硫酸渣与硫酸的固液比为1:3,硫酸质量分数为20%-25%,反应温度为80℃,反应时间为6 h,搅拌强度为200 r/min;最佳结晶精制条件:结晶溶液pH值1:3,温度为60℃,温度海60℃;除杂最佳条件:pH值约为4.5;冷却结晶温度控制在20℃,结晶秣过程为30℃于燥6 h.     

Evaluation of two models of a slipmeter

The aim of the study was to compare the performances of the Brungraber Mark II (BM II) and Mark III (BM III) slipmeters. Friction measurements with the two slipmeters were conducted in a laboratory using four footwear materials, four floor types, and three surface conditions. Both the coefficient of friction (COF) values obtained with the slipmeters and the force platform-based COF values were measured. The COF measured with the BM II was slightly higher than that measured with the BM III with a R² of 0.83. A comparison of the averaged normal force between the two slipmeters showed that the BM II generated a significantly higher normal force than the BM III at a low COF and the difference of the normal force between the two slipmeters decreased when the COF value was increased. The regression analysis results in this study showed that the force platform-based COF values were closer to the COF values obtained with the BM III than with the BM II. The R² values for the regression model between the COF values obtained from the slipmeter and the force platform were 0.90 and 0.79 for the BM II and BM III, respectively.     

城市网格化管理与安全社区建设

社区是城市的基本组成单元,社区安全是保障城市平稳、安全、有序运行的基础。随着我国经济的迅速发展和改革的不断深化,社区在城市管理中的基础地位和作用日益突出,安全社区的建设也越来越引起国内外专家、学者的广泛关注。