Assessment of heavy metals (Cd and Pb) and micronutrients (Cu, Mn, and Zn) of paddy (Oryza sativa L.) field surface soil and water in a predominantly paddy-cultivated area at Puducherry (Pondicherry, India), and effects of the agricultural runoff on the elemental concentrations of a receiving rivulet

The concentrations of toxic heavy metals—Cd and Pb and micronutrients—Cu, Mn, and Zn were assessed in the surface soil and water of three different stages of paddy (Oryza sativa L.) fields, the stage I—the first stage in the field soon after transplantation of the paddy seedlings, holding adequate amount of water on soil surface, stage II—the middle stage with paddy plants of stem of about 40 cm length, with sufficient amount of water on the soil surface, and stage III—the final stage with fully grown rice plants and very little amount of water in the field at Bahour, a predominantly paddy cultivating area in Puducherry located on the southeast Coast of India. Comparison of the heavy metal and micronutrient concentrations of the soil and water across the three stages of paddy field showed their concentrations were significantly higher in soil compared with that of water (p?<?0.05) of the fields probably because of accumulation and adsorption in soil. The elemental concentrations in paddy soil as well as water was in the ranking order of Cd?>?Mn?>?Zn?>?Cu?>?Pb indicating concentration of Cd was maximum and Pb was minimum. The elemental concentrations in both soil and water across the three stages showed a ranking order of stage II?>?stage III?>?stage I. The runoff from the paddy fields has affected the elemental concentrations of the water and sediment of an adjacent receiving rivulet.     

Soil biogeochemical characteristics influenced by alum application in a municipal wastewater treatment wetland

Constructed treatment wetlands are a relatively low-cost alternative used for tertiary treatment of wastewater. Phosphorus (P) removal capacity of these wetlands may decline, however, as P is released from the accrued organic soils. Little research has been done on methods to restore the treatment capacity of aging constructed wetlands. One possibility is the seasonal addition of alum during periods of low productivity and nutrient removal. Our 3-mo mesocosm study investigated the effectiveness of alum in immobilizing P during periods of reduced treatment efficiency, as well as the effects on soil biogeochemistry. Eighteen mesocosms were established, triplicate experimental and control units for Typha sp., Schoenoplectus californicus, and submerged aquatic vegetation (SAV) (Najas guadalupensis dominated). Alum was slowly dripped to the water column of the experimental units at a rate of 0.91 g Al m(-2) d(-1) and water quality parameters were monitored. Soil cores were collected at experiment initiation and completion and sectioned into 0- to 5- and 5- to 10-cm intervals for characterization. The alum floc remained in the 0- to 5-cm surface soil, however, soil pH and microbial parameters were impacted throughout the upper 10 cm with the lowest pH found in the Typha treatment. Plant type did not impact most biogeochemical parameters; however, data were more variable in the SAV mesocosms. Amorphous Al was greater in the surface soil of alum-treated mesocosms, inversely correlated with soil pH and microbial biomass P in both soil layers. Microbial activity was also suppressed in the surface soil of alum-treated mesocosms. This research suggests alum may significantly affect the biogeochemistry of treatment wetlands and needs further investigation.     

Intracellular biosynthesis of Au and Ag nanoparticles using ethanolic extract of Brassica oleracea L. and studies on their physicochemical and biological properties

In this present study, we reported broccoli(Brassica oleracea L.) as a potential candidate for the synthesis of gold and silver nanoparticles(NPs) in green chemistry method. The synthesized metal nanoparticles are evaluated their antimicrobial efficacy against different human pathogenic organisms. The physico-chemical properties of gold nanoparticles were analyzed using different analytical techniques such as a UV–Vis spectrophotometer, Field Emission Scanning Electron Microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction and a Fourier Transform Infrared spectrophotometer. In addition, gold and silver NP antimicrobial efficacy was checked by disc diffusion assay. UV–Vis color intensity of the nanoparticles was shown at 540 and 450 nm for gold and silver nanoparticles respectively. Higher magnification of the Field Emission Scanning Electron Microscopy image shows the variable morphology of the gold nanoparticles such as spherical, rod and triangular shapes and silver nanoparticles were seen in spherical shapes. The average spherical size of the particles was observed in 24–38 nm for gold and 30–45 nm for silver NPs. X-ray diffraction pattern confirmed the presence of gold nanoparticles and silver nanoparticles which were crystalline in nature. Additionally,the functional metabolites were identified by the Fourier Transform Infrared spectroscopy. IR spectra revealed phenols, alcohols, aldehydes(sugar moieties), vitamins and proteins are present in the broccoli extract which are accountable to synthesize the nanoparticles. The synthesized gold and silver NPs inhibited the growth of the tested bacterial and fungal pathogens at the concentration of 50 μg/m L respectively. In addition, broccoli mediated gold and silver nanoparticles have shown potent antimicrobial activity against human pathogens.     

Development of chitosan-alginate based biosorbent for the removal of p-chlorophenol from aqueous medium

Removal of p-chlorophenol (pCP) from synthetic aqueous solutions was studied through adsorption on a biosorbent developed from chitosan (CS) and sodium alginate (SA), the natural cationic and anionic polysaccharides, respectively. Chitosan-coated sodium alginate beads were prepared and treated with calcium chloride solution in order to improve the stability as well as hydrophobic character. The resulting beads (CS/CA) were characterized using FTIR spectra, scanning electron microscopy (SEM), and BET surface analysis. The efficiency of this biosorbent in removing pCP from aqueous medium was studied under batch equilibrium and dynamic column flow experimental conditions. The binding capacity of the biosorbent was studied as a function of initial pH, contact time, initial concentration of adsorbate and amount of biomass. The data were fitted to pseudo-first-order, pseudo-second-order, and Weber–Morris models and found that the adsorption process followed pseudo-first-order kinetics. Further, the equilibrium data were fitted to Freundlich, Langmiur, and Dubinin–Radushkevich (D–R) adsorption isotherms and the isotherm constants were evaluated for adsorption of pCP. The maximum monolayer adsorption capacity of CS/CA beads was found to be 127 mg g^?1. Column flow results were used to generate breakthrough curves. The experimental results suggested that the chitosan–calcium alginate blended biosorbent was effective for the removal of pCP from aqueous medium.     

Geotechnical properties of fresh municipal solid waste at Orchard Hills Landfill, USA

This paper presents the results of a laboratory investigation to determine the geotechnical properties of fresh municipal solid waste (MSW) collected from the working phase of Orchard Hills Landfill located in Davis Junction (Illinois, USA). Laboratory testing was conducted on shredded MSW to determine the compaction, hydraulic conductivity, compressibility, and shear strength properties at in-situ gravimetric moisture content of 44%. In addition, the effect of increased moisture content during leachate recirculation on compressibility and shear strength of MSW was also investigated by testing samples with variable gravimetric moisture contents ranging from 44% to 100%. Based on Standard Proctor tests, a maximum dry density of 420 kg/m(3) was observed at 70% optimum moisture content. The hydraulic conductivity varied in a wide range of 10(-8)-10(-4)m/s and decreased with increase in dry density. Compression ratio values varied in a close range of 0.24-0.33 with no specific trend with the increase in moisture content. Based on direct shear tests, drained cohesion varied from 31 to 64 kPa and the drained friction angle ranged from 26 to 30 degrees. Neither cohesion nor friction angle demonstrated any correlation with the moisture content, within the range of moisture contents tested. The consolidated undrained triaxial shear tests on saturated MSW showed the total strength parameters (c and phi) to be 32 kPa and 12 degrees, and the effective strength parameters (c' and phi') to be 38 kPa and 16 degrees. The angle of friction (phi) decreased and cohesion (c) value increased with the increase in strain. The effective cohesion (c') increased with increase in strain; however, the effective angle of friction (phi') decreased first and then increased with the increase in strain. Such strain-dependent shear strength properties should be properly accounted in the stability analysis of bioreactor landfills.     

The significance of trisomy 7 mosaicism in chorionic villus cultures

Two cases of mosaic trisomy 7 confined to the cultured cells and not found in direct preparation were detected from 200 consecutive first-trimester chorionic villus samples (CVS) analysed. The mosaicism was similar in the two cases, but the pregnancy outcome was different. In both cases, the direct metaphases from the CVS were 46, XY. Culture metaphases were mos46,XY/47,XY, + 7; the trisomy 7 was seen in 34 per cent of cells from case 1 and 53 per cent from case 2. A sonogram at 15¹/₂ weeks revealed fetal death in utero in case 1, and the patient declined amniocentesis. The fetal tissue failed to grow in culture, but the placental cultured cells were 47,XY, + 7 in 28 (100 per cent) cells analysed. In the second case, all the amniotic fluid cells were 46,XY and the pregnancy resulted in a normal male with a 46,XY karyotype in the cord blood and foreskin fibroblast cultures. The term placenta was mosaic with 13/163 (8 per cent) trisomy 7 cells. Extensive cytogenetic studies on the placenta for the first time confirmed trisomy 7 mosaicism confined to the villus cultures.     

Stable chlorine intramolecular kinetic isotope effects from the abiotic dehydrochlorination of DDT

INTENTION, GOAL, SCOPE, BACKGROUND: Identifying different sources and following reaction pathways of chlorinated organic contaminants in the environment can be challenging, especially when only their concentrations are available. Compound-specific stable chlorine measurements of some contaminants have recently been shown to provide additional information and an increased understanding of their biogeochemistry. These studies, however, have been generally limited to volatile molecules. OBJECTIVE: Here, the stable chlorine isotope ratios of the semi-volatile pesticide, 1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (DDT) were investigated. Specifically, the intramolecular stable chlorine isotopic compositions of DDT and the kinetic isotope effect (KIE) for the abiotic dehydrochlorination of DDT to 2,2-bis(p-chlorophenyl)-1,1-dichloroethene (DDE) were determined. METHODS: Selective chemical oxidation of DDT to dichlorobenzophenone (DCBP) and analysis of each compound was used to calculate the stable chlorine isotope ratios of the alkyl and aromatic chlorines in DDT. To determine the KIE for dehydrochlorination, DDT was reacted in a basic solution to yield DDE at 52 degrees C, 60 degrees C, and 72 degrees C for 3, 5, and 5 days, respectively. RESULTS AND DISCUSSION: Significant intramolecular stable chlorine isotopic differences were observed in one sample of DDT where the alkyl and aromatic delta 37Cl values were -5.76 +/- 0.45 and -2.21 +/- 0.24%@1000, respectively. Dehydrochlorination of DDT to DDE in basic solutions at 52, 60, and 70 degrees C resulted in a substantial intramolecular KIE where the alkyl chlorines of DDE shifted by approximately 3%@1000 relative to the alkyl chlorines in DDT. However, no temperature dependence was observed. The KIE, calculated by an iterative program, was 1.009. CONCLUSIONS: Intramolecular differences in the stable chlorine isotope ratios were observed in DDT and this is the first such finding. Dehydrochlorination of DDT yields a measurable and distinct intramolecular stable chlorine KIE. RECOMMENDATION AND OUTLOOK: The results of this study demonstrate the existence of significant intramolecular differences in chlorinated organic compounds. Many other chlorinated semi-volatile and volatile organic contaminants are synthesized from multiple sources of chlorine, and we recommend that similar studies be performed on many such molecules in order to attain a clear understanding of their intramolecular chlorine isotopic differences. The existence of a measurable KIE for the dehydrochlorination of DDT to DDE shows the potential strength of using isotopic measurements to investigate the biogeochemistry of these important compounds. For example, the isotopically depleted aqueous chloride produced by dehydrochlorination of DDT to DDE may be a useful tracer of these reactions in freshwater environments.     

Variations in bottom sediment nutrient and metal concentrations in the Genesee River watershed,New York

Variations in nutrient and metal concentrations of fluvial sediment may be due to varying combinations of natural and man-made factors: basin geology, surface erosion, riverbank erosion, industrial or other cultural contamination, the presence of minerals rich in trace elements (e.g. chromite), sediment ion-exchange capacity, sediment organic content, and the presence of metallic oxides. The data reported here were obtained in a study in New York State of sediment transport from the Genesee River watershed to Lake Ontario (6,500 km²; 2,400 sq.mi.). One hundred bottom sediment samples collected over a period of a year were chemically analyzed for aluminium, chromium, copper, iron, manganese, nickel, lead, zinc, total carbon, total organic carbon, total nitrogen, and phosphorus. The metal concentrations (arithmetic means ±S.D., in μg/g) were: Al, 6,660±2,620; Cr, 14±9; Cu, 18±7; Fe, 15,060±7,312; Mn, 424±212; Ni, 23±13; Pb, 40±67; and Zn, 69±37. For the major nutrients the results (mean ±1 S.D. in %) were: total carbon, 2.06 ± 1.68; total organic carbon, 1.37 ± 1.28; total nitrogen, 0.105 ± 0.098; and phosphorus, 0.0560 ± 0.014.     

A numerical model for drying of spherical object in an indirect type solar dryer and estimating the drying time at different moisture level and air temperature

A numerical model for simultaneous heat and mass transfer was developed for solar drying of spherical objects and the object considered is green peas. Solar collector outlet temperature is assumed as drying chamber temperature and justified through energy balance equations. Assumptions are imposed on heat and mass transfer governing equations without losing the physics of the problem. Discretization is performed by finite difference method with implicit scheme. To generalize, the governing equation and boundary conditions are non-dimensionalized. The set of finite difference equations was solved by Tridiagonal Matrix Algorithm and a computer code in MATLAB was developed to solve them. The drying curves showed two stages of drying, initial, and secondary drying stage. At all drying temperatures and drying time, the center moisture was maximum and it was minimum at the boundary. A percentage of 85.67 surface moisture content and 25.33% center moisture was eliminated in the first 1 hr at 348 K. The product should be dried up to 7.45, 4.74, and 3.74 hr at air drying temperatures of 318, 333, and 348 K respectively, to maintain 10% of the product’s initial moisture content. The result is compared with the experimental result from literature and they are found to be in good agreement.     

Hydrometallurgical processing of Nd–Fe–B magnets for Nd purification

An evaluation of various metal purification processes subsequent to the leaching processing of the neodymium (Nd) product from neodymium–iron–boron (Nd–Fe–B) magnets has been conducted. These post-leaching purification processes included precipitation; replacement and electrolysis were studied in order to check the purity of the recovered neodymium. A hydrometallurgical investigation was adopted to digest the metal content of the scrap Nd–Fe–B magnets for the recovery of valuable Nd metal and other metals such as Fe, B, Co and Ni. The effect of leaching conditions such as solid-to-liquid ratio and temperature were optimized and 100 % Nd, 100 % Fe, 100 % B and 85.87 % Co leaching efficiencies were achieved under these conditions. The coating material of the magnet, Ni, achieved 50 % impregnation after increasing the reaction temperature to 70 °C. The metals present in the optimal leaching solution were recovered 99 % by pH adjustment. However, the replacement had the highest separation efficiency for the recovery of Nd metal. Further, the optimal leaching Nd–Fe–B solution was subjected to the electrolysis processes in order to verify the recovery efficiency for all metals.