Comparative analysis of anaerobically digested wastes flow properties

The flow curve of anaerobically digested wastes from different origins was determined through rheological measurements. Regardless of their origin, samples can be divided into two families: simple non-Newtonian liquids well modelled by basic power law below 10%DC and viscoelastic liquids with a yield stress, well modelled by a Herschel–Bulkley model above. In all the cases, the rheological behaviour is driven by both the organic content and the volatile fraction (organic content/solid content), indicating that anaerobic digestion tends to smooth the rheological characteristics of organic wastes, whichever their origins.     

Investigation on the effect of sintering temperature on kaolin hollow fibre membrane for dye filtration

Despite its extraordinary price, ceramic membrane can still be able to surpass polymeric membrane in the applications that require high temperature and pressure conditions, as well as harsh chemical environment. In order to alleviate the high cost of ceramic material that still becomes one of the major factors that contributes to the high production cost of ceramic membrane, various attempts have been made to use low cost ceramic materials as alternatives to well-known expensive ceramic materials such as alumina, silica, and zirconia in the fabrication of ceramic membrane. Thus, local Malaysian kaolin has been chosen as the ceramic material in this study for the preparation of kaolin hollow fibre membrane since it is inexpensive and naturally abundant in Malaysia. Due to the fact that the sintering process plays a prominent role in obtaining the desired morphology, properties, and performances of prepared ceramic membrane, the aim of this work was to study the effect of different sintering temperatures applied (ranging from 1200 to 1500 °C) in the preparation of kaolin hollow fibre membrane via dry/wet phase inversion-based spinning technique and sintering process. The morphology and properties of membrane were then characterised by SEM, AFM, FTIR, XRD, and three-point bending test, while the performances of membrane were investigated by conducting water permeation and Reactive Black 5 (RB5) dye rejection tests. From the experimental results obtained, the sintering temperature of 1400 °C could be selected as the optimum sintering temperature in preparing the kaolin hollow fibre membrane with the dense sponge-like structure of separation layer that resulted in the good mechanical strength of 70 MPa with the appreciable water permeation of 75 L/h m² bar and RB5 rejection of 68%.     

Influence of the geomembrane on time-lapse ERT measurements for leachate injection monitoring

Leachate recirculation is a key process in the operation of municipal waste landfills as bioreactors. To quantify the water content and to evaluate the leachate injection system, in situ methods are required to obtain spatially distributed information, usually electrical resistivity tomography (ERT). However, this method can present false variations in the observations due to several parameters. This study investigates the impact of the geomembrane on ERT measurements. Indeed, the geomembrane tends to be ignored in the inversion process in most previously conducted studies. The presence of the geomembrane can change the boundary conditions of the inversion models, which have classically infinite boundary conditions. Using a numerical modelling approach, the authors demonstrate that a minimum distance is required between the electrode line and the geomembrane to satisfy the good conditions of use of the classical inversion tools. This distance is a function of the electrode line length (i.e. of the unit electrode spacing) used, the array type and the orientation of the electrode line. Moreover, this study shows that if this criterion on the minimum distance is not satisfied, it is possible to significantly improve the inversion process by introducing the complex geometry and the geomembrane location into the inversion tools. These results are finally validated on a field data set gathered on a small municipal solid waste landfill cell where this minimum distance criterion cannot be satisfied.     

Assessing the Influence of Social Responsibility on Reputation: An Empirical Case-Study in Agricultural Cooperatives in Spain

The attention to ethics has gradually become a concurrent topic of modern companies’ management. In the last years Social Responsibility has become a key issue in the strategic agenda of competitive agriculture cooperatives. However, reputation management has not been a visible strength in the cooperative enterprises. First of all, this work theoretically analyzes the relationship between Social Responsibility and reputation in cooperatives. Later, from a practical point of view, we carry on an empirical analysis focused on the olive oil cooperatives in the south of Spain, in the province of Jaén. With respect to the previous studies on the topic, this work reveals a main reason of interest reinforcing the role of research in addressing real problems of cooperatives. The article points out the characteristics of this kind of agribusiness and shows the importance of the adoption of a responsible orientation in fostering reputation for creating sustainable competitive advantages.     

Effects of fly ash addition on physical properties of porous clay-fly ash composites via polymeric replica technique

The porous composites of clay and fly ash have the potential to be used in many fields, such as catalyst support and gas adsorbents. In this study, various ratios of fly ash (1–2) with different percentage of suspension (50–70 wt%) were applied to produce porous clay-fly ash composites via polymeric replica technique. Fabrication process starts by mixing clay and fly ash in distilled water to form slurry. The process is followed by fully immersing polymer sponge in slurry. The excess slurry is then removed through squeezing. Finally, the sponge coated with slurry is sintered at 500 and 1250 °C for 1 h. It is found that the compressive strength of porous composites improves significantly (0.178–1.28 MPa) when the amount of clay-fly ash suspension mixture (50–70 wt%) increases. The compressive strength of porous composites is mainly attributed to the mullite, quartz and amorphous phase formations. These results are supported by X-ray diffraction analysis. On the other hand, increase in the amount of suspension reduces the apparent density (from 2.44 to 2.32 g/cm³) and porosity (from 97 to 85 %). The reduction in apparent density is believed to be caused by the presence of high fly ash content in porous composites. The melted fly ash cenospheres have closed the internal pores and increased density of samples. Higher suspension level not only reduces porosity, but also increases close pores of the porous composites. The results are justified through the observation from the structures of porous clay-fly ash composites.     

Thermotolerant coliform loadings to coastal areas of Santa Catarina (Brazil) evidence the effect of growing urbanisation and insufficient provision of sewerage infrastructure

Thermotolerant coliform (TC) loadings were quantified for 49 catchments draining into the North and South Bays of Santa Catarina (SC, southeastern Brazil), an area known for its tourism and aquaculture. TC loadings were calculated based on flow measurements taken in 26 rivers. TC concentrations ere quantified based on surface water samples collected at 49 catchment outlets in 2012 and 2013. Median TC loads ranged from 3.7 × 10³ to 6.8 × 10⁸ MPN s^?1. TC loadings in the catchments increased in proportion to increases in resident human population, population density and percentage of urbanised area. Catchments with more than 60% of area covered by wastewater collection and treatment systems had higher TC loads per person than catchments with less than 25%. Based on the study catchments, these results indicate that current sewerage infrastructure is ineffective in reducing contamination of faecal origin to surface waters. These findings have important implications for the management of microbiological health hazards in bathing, recreational and shellfish aquaculture waters in the North and South Bays of Santa Catarina Island.     

Toward Cyborg PPGIS: exploring socio-technical requirements for the use of web-based PPGIS in two municipal planning cases,Stockholm region,Sweden

Web-based Public Participation Geographic Information Systems (PPGIS) are increasingly used for surveying place values and informing municipal planning in contexts of urban densification. However, research is lagging behind the rapid deployment of PPGIS applications. Some of the main opportunities and challenges for the uptake and implementation of web-based PPGIS are derived from a literature review and two case studies dealing with municipal planning for urban densification in the Stockholm region, Sweden. A simple clustering analysis identified three interconnected themes that together determine the performance of PPGIS: (i) tool design and affordances; (ii) organisational capacity; and (iii) governance. The results of the case studies augment existing literature regarding the connections between the different socio-technical dimensions for the design, implementation and evaluation of PPGIS applications in municipal planning. A cyborg approach to PPGIS is then proposed to improve the theoretical basis for addressing these dimensions together.     

The methylic versus the ethylic route: considerations about the sustainability of Brazilian biodiesel production

Brazil is considered one of the world’s leading producers of biofuels given the predominance of ethanol fuel in its energy matrix. However, despite the prominence of Brazil in ethanol production, the vast majority of biodiesel production plants in Brazil use methanol instead of ethanol as the alcohol for transesterification reaction, as is generally the case in the rest of the world. The aim of this paper is therefore to examine the transesterification process in the Brazilian biodiesel production in terms of sustainability. In this regard, it was necessary to evaluate the way in which the industrial process is currently carried out, the role of government incentives or subsidies for the use of ethanol to produce biodiesel, and the investments of companies in technology development for the same purpose. This study presents indications that the development of the biodiesel market in Brazil is still oriented toward a production model which is inconsistent with the environmental and social aspects of sustainability.     

Toward a new understanding of the links between poverty and illegal wildlife hunting

Conservation organizations have increasingly raised concerns about escalating rates of illegal hunting and trade in wildlife. Previous studies have concluded that people hunt illegally because they are financially poor or lack alternative livelihood strategies. However, there has been little attempt to develop a richer understanding of the motivations behind contemporary illegal wildlife hunting. As a first step, we reviewed the academic and policy literatures on poaching and illegal wildlife use and considered the meanings of poverty and the relative importance of structure and individual agency. We placed motivations for illegal wildlife hunting within the context of the complex history of how wildlife laws were initially designed and enforced to indicate how hunting practices by specific communities were criminalized. We also considered the nature of poverty and the reasons for economic deprivation in particular communities to indicate how particular understandings of poverty as material deprivation ultimately shape approaches to illegal wildlife hunting. We found there is a need for a much better understanding of what poverty is and what motivates people to hunt illegally.     

Solar energy for electricity and fuels

Solar energy conversion into electricity by photovoltaic modules is now a mature technology. We discuss the need for materials and device developments using conventional silicon and other materials, pointing to the need to use scalable materials and to reduce the energy payback time. Storage of solar energy can be achieved using the energy of light to produce a fuel. We discuss how this can be achieved in a direct process mimicking the photosynthetic processes, using synthetic organic, inorganic, or hybrid materials for light collection and catalysis. We also briefly discuss challenges and needs for large-scale implementation of direct solar fuel technologies.