RETRACTED:

Jianfeng Li  Sandra M.Y. Lee  Wenmao Liu 《Process Safety and Environmental Protection》2013,91(3):213-220

Media surface properties and the development of nitrifying biofilms in mixed cultures for wastewater treatment

Plastic was tested to select biofilm support media that would enhance nitrification in the presence of heterotrophs. Eight different types (acrylonitrile butadiene styrene, nylon, polycarbonate, polyethylene, polypropylene, polytetrafluoroethylene (PTFE), polyvinyl chloride and tufnol) were immersed in an aerobic fed-batch reactor receiving domestic settled wastewater. Nitrification rates did not correlate with biomass concentrations, nor surface roughness of the plastics as measured by atomic force microscopy (AFM). The maximum nitrification rate of 1.5 g/m² d^?1 was obtained from biofilms growing on PTFE which had the lowest surface adhesion force (8 nN). Nitrification rates for the biofilms were inversely correlated with the attraction forces as measured by AFM.     

Experimental and theoretical investigations for mitigating NaAlH4 reactivity risks during postulated accident scenarios involving exposure to air or water

Experimental and theoretical studies were conducted to investigate the pyrophoricity and water-reactivity risks associated with employing sodium alanate (NaAlH₄) complex metal hydride in on-board vehicular hydrogen (H₂) storage systems. The ignition and explosivity of NaAlH₄ upon exposure to oxidizers in air or water were attributed to the spontaneous formation of stable hydroperoxyl intermediates on the NaAlH₄ surface and/or H₂ production, as well as the large driving force for NaAlH₄ conversion to favorable hydroxide products predicted by atomic and thermodynamic modeling. The major products from NaAlH₄ exposure to air: NaAl(OH)₄, gibbsite and bayerite Al(OH)₃, and Na₂CO₃ observed by XRD, were identified to be formed by surface-controlled reactions. The reactivity risks were significantly minimized, without compromising de-/re-hydrogenation cyclability, by compacting NaAlH₄ powder into wafers to reduce the available surface area. These core findings are of significance to risk mitigation and H₂ safety code and standard development for the safe use of NaAlH₄ for on-board H₂ storage in light-duty vehicles.     

静电基本参数的测试原理

静电测试是整个静电防护工程中不可或缺的组成部分,也是静电防护设计和管理的依据.本文主要介绍了静电基本参数中的静电电位、静电电容和静电电量的测试原理,并结合具体测试数据对测试的方法和仪器进行了分析.     

好氧颗粒污泥沉降选择实验研究与定量描述

以序批式反应器培养的成熟好氧颗粒污泥为对象,研究沉淀高度对颗粒数、比重、污泥浓度、粒径分布及选择系数的影响.结果表明,随着沉淀高度的增加,污泥浓度在沉淀时间为30 s时由0.24 mg.L-1明显增加至6.07 mg.L-1,平均粒径从450μm增加到550μm,颗粒圆形度增加12.67%,而复杂度减小13.47%,说明粒径较大、形状较规则的颗粒沉降较快,从而更易在沉降选择过程中得以保留.根据选择压原理,结合颗粒污泥沉降实验结果引入选择系数.实验和计算结果显示,在任意沉淀高度,选择系数随粒径和密度的增大而增加.随着沉淀高度的增加,直径>600～800μm的颗粒选择系数增加,小颗粒趋势与之相反,说明增大排水比有利于大颗粒保留而絮体被筛选出反应器,而低的排水比会使污泥颗粒化过程放缓.该研究结果可望对加速污泥颗粒化过程和提高其稳定性提供科学的理论依据和指导.     

Biological methane production coupled with sulfur oxidation in a microbial electrosynthesis system without organic substrates

Methane is produced in a microbial electrosynthesis system (MES) without organic substrates. However, a relatively high applied voltage is required for the bioelectrical reactions. In this study, we demonstrated that electrotrophic methane production at the biocathode was achieved even at a very low voltage of 0.1 V in an MES, in which abiotic HS⁻ oxidized to SO₄²⁻ at the anodic carbon-cloth surface coated with platinum powder. In addition, microbial community analysis revealed the most probable pathway for methane production from electrons. First, electrotrophic H₂ was produced by syntrophic bacteria, such as Syntrophorhabdus, Syntrophobacter, Syntrophus, Leptolinea, and Aminicenantales, with the direct acceptance of electrons at the biocathode. Subsequently, most of the produced H₂ was converted to acetate by homoacetogens, such as Clostridium and Spirochaeta 2. In conclusion, the majority of the methane was indirectly produced by a large population of acetoclastic methanogens, namely Methanosaeta, via acetate. Further, hydrogenotrophic methanogens, including Methanobacterium and Methanolinea, produced methane via H₂.     

纹缟虾虎鱼对Cu~(2+)、Cd~(2+)和氨氮的毒性响应和敏感性分析

以纹缟虾虎鱼为受试生物,分别进行了Cu~(2+)、Cd~(2+)和氨氮为环境因子的急性毒性实验和氨氮慢性暴露实验,结合文献数据分析纹缟虾虎鱼对3种污染物的敏感性。结果表明,Cu~(2+)、Cd~(2+)和氨氮对纹缟虾虎鱼的EC50分别为4.527、40.408和63.182mg·L~(-1)。组织切片结果显示,氨氮暴露能够引起纹缟虾虎鱼肝组织结构退化,组织细胞畸变,其损伤程度随着氨氮浓度的升高而加剧。氨氮暴露对肠管未见明显影响。敏感性分析结果表明,纹缟虾虎鱼对Cu~(2+)、Cd~(2+)和氨氮的累积概率分别为83.33%、96.27%和90.48%,均表现为不敏感。在Cu~(2+)、Cd~(2+)和氨氮对海洋生物的敏感性排名中,纹缟虾虎鱼分别在第31/35、32/32和19/20位。在8~12种海洋鱼类中,纹缟虾虎鱼对上述3种污染物的敏感性都处在较低水平。     

Recycling thin film transistor liquid crystal display (TFT-LCD) waste glass produced as glass–ceramics

The waste electrical and electronic equipment (WEEE) directives are designed to deal with the rapidly increasing waste stream comprised of electrical and electronic equipment. Recycling electrical and electronic equipment reduces the quantity of waste going to final disposal. The demand for thin film transistor liquid crystal display (TFT-LCD) panels, commonly used in everyday electronic products, is increasing. Conventionally adopted treatments of TFT-LCD waste glass cannot meet WEEE directives. This study adopts the following operating conditions in fabricating glass–ceramics: sintering temperature of 800–950 °C; sintering time of 6 h; and, temperature increase rate of 5 °C/min. The glass–ceramic samples then underwent a series of tests, including the Vickers hardness, water absorption and porosity tests, to determine product quality. The Vickers hardness was 12.1 GPa when fired at 900 °C for 6 h, and density was 2.4 g/cm³ and water absorption was 0%. Thus, TFT-LCD waste glass can be regarded as a good glass–ceramic material.     

Development of vermicast from sludge and powdered oyster shell

Soil acidification is one of the rising land degradation issues facing world agriculture. The risk of acidification is currently being assessed as part of agriculture productivity and sustainable theme. This study was conducted to produce a new vermicomposting cast as a recycling resource derived from municipal sewage sludge and waste oyster shell. The earthworm, Eisenia Andrei, was fed under different conditions. The most suitable mixture was 77:23 w/w% of sewage sludge and waste oyster shell. Powdered oyster shell (POS) sludge blend provided a stable pH, due to its buffering capacity during vermiculture because of the Ca²⁺ and OH^? release effect. The vermicast products fulfilled the cast standards of Korea Ministry of Environment for all the parameters such as moisture content, pH, salinity, organic carbon, TKN, Phosphate, and heavy metals. Slowly released organic matter when added to soil improves the capacity of the soil to hold nutrients for plants, improve soil aeration for roots, and improves soil drainage. This product will be an addition to already-commercialized sludge vermicast as a higher value product.