The Effect of Fuel Composition on Atmospheric Aerosol Due to Auto Exhaust

Aerosols attributable to automobile exhaust can be classified as two types—primary aerosol (initially present in the exhaust) and secondary aerosol (generated photochemically from hydrocarbons and nitrogen oxides in the exhaust). In this study, investigation was made of possible effects of motor-fuel composition on the formation of these aerosols. Secondary aerosol, of principal interest in this work, was produced by irradiating auto exhaust in Battelle-Columbus’ 610 ft³ environmental chamber. A limited number of determinations of primary aerosol in diluted auto exhaust was made at the exit of a 36 ft dilution runnel. Determination of both primary and secondary aerosol was based on light-scattering measurements.

Exhaust was generated with seven full-boiling motor gasolines, both leaded and nonleaded, in a 1967 Chevrolet which was not equipped with exhaust-emission control devices. Changes in fuel composition produced a maximum factor of three difference in light scattering due to primary aerosol. Aerosol yields, for consecutive driving cycles on the same fuel, vary considerably; as a result, ranking the fuels on the basis of average primary aerosol yield was not very meaningful. In addition to fuel composition, the more important independent variables are initial SO₂ concentration, relative humidity and initial hydrocarbon concentration. Statistical analysis of the data indicates that the seven test fuels can be divided into two arbitrary groups with regard to secondary aerosol-forming potential. The fuels in the lower light-scattering group had aromatic contents of 15 and 21%, while those in the higher light-scattering group had aromatic contents of 25, 48, and 55%. Although the fuels can be grouped on the basis of a compositional factor, the grouping of fuels with aromatic content ranging from 25 to 55% indicates that this compositional factor cannot be equated simply with aromatic content. In an associated study of the aerosol-forming potential of individual hydrocarbons prominent in auto exhaust, it was observed that aromatics produce substantially more photochemical aerosol than olefins and paraffins. However, experiments with binar/hydrocarbon mixtures containing aromatjcs, as well as in these exhaust experiments, a strong dependence of aerosol yield on the aromatic components is is not observed. Thus, the data indicate that the dependence of secondary aerosol formation on fuel factors is a complex one and cannot be predicted solely on the basis of a sirigle hydrocarbon component reactivity scale.

The two types of automobile aerosol did not have the same dependence on fuel, composition. The variation in total light scattering attributable to primary plus secondary aerosol was less than that due to either component alone. It therefore was concluded that the light scattering due to automobile exhaust emissions in these experiments was not significantly affected by changing fuel composition.     

Nitrogen Compounds other than NO in Automobile Exhaust Gas

Recent studies of organic pyrolyses in the presence of nitric oxide have shown that various nitogen compounds, such as hydrogen cyanide (HCN) and aceto-nitrile (CH₃CN) are formed. This suggests the possibility that such compounds will be found in internal combustion processes, and may be present in automobile exhaust gases. The present paper describes some gas-chromatographic and wet analyses of exhaust gases. It is concluded that the amounts of hydrogen cyanide are less than 1 ppm, but that various organic nitrogen compounds may reach a level of about 100 ppm. The significance of these results is discussed.     

Plume Dispersion in a Mountainous River Valley during Spring

The dispersion of hot plumes emitted from a smelter complex located In the Columbia River Valley, British Columbia, was evaluated under stable and neutral conditions during two mornings In spring. Spatial measurements of SO₂ and temperature within the plume were obtained by immersion probing using fast response helicopter and automobile mounted Instrumentation. In addition, meteorological measurements of vertical wind and temperature profiles at, and downwind from, the smelter were obtained from minisonde balloon releases. With weak down-valley winds, it was found that the plume axis elevations were generally lower during both stable and neutral conditions than would be predicted by Briggs plume-rise formulae. In contrast, plume dispersion, although confined in the horizontal by the steep valley walls during both stability regimes, was significantly enhanced by exceptionally good lateral mixing, particularly close to the source.     

Product Guide/1975

Measurements conducted on full-scale hazardous waste incinerators have occasionally shown a relationship between carbon monoxide (CO) emissions and emissions of toxic organic compounds. In this study, four mixtures of chlorinated C₁ and C₂ hydrocarbons were diluted in commercial-grade heptane and burned in a water-cooled turbulent flame reactor (TFR) under two different excess air levels. No correlation between CO and organic emissions could be discerned. Reasons for this lack of observable correlations are discussed in terms of combustion and chemical reaction kinetic theory.     

Evaluation of Selected Gaseous Halocarbons for Use in source Test Performance Audits

A repository of 38 gaseous organic compounds in compressed gas cylinders has been established by EPA. This repository was established to provide standards for source test performance audits, that is, quantitative quality assurance tests. Among these compounds are ten halogenated organic species, which are the focus of this paper.

Stability studies of all ten compounds have been performed to determine the feasibility of using them as performance audit standards. Results indicate that all of the halocarbons tested are adequately stable to be used as reliable audit standards.

Subsequent to completion of stability studies, four of the ten halocarbons were used in source test performance audits. Results are available at this time for two of the four compounds; the results show agreement within 10% of the concentrations previously established by Research Triangle Institute.     

R&D Activities,Operating Experience Discussed at Fabric Alternatives Forum

ABSTRACT

Previously reported volatile organic compounds (VOC) radiocarbon (¹⁴C) measurements for 1992 summertime Atlanta, GA, have been compared with chromatographic data and emissions inventory predictions. The chromatographic approach that was used provided a more comprehensive VOC characterization than typically achieved, and the emissions inventory was research-grade level (date-, site-, and time-specific). The comparisons are in general agreement that biogenic emissions contribute only modestly (<10%) to the VOC content of the particular ambient samples that were collected and measured. The choices of sampling site (near city-center) and times (early morning and late evening) are major influences on the results, which consequently should not be regarded as representing the average VOC biogenic impact for the Atlanta area.     

A New Audit Technique for EPA Method 25

A simple, inexpensive, and accurate technique for evaluating or auditing the sampling, recovery, and analytical phases of EPA Source Reference Method 25 has been developed. The technique involves spiking a U-shaped stainless steel cartridge containing Tenax® with known quantities of selected organic compounds and thermally desorbing them at temperatures from 160°C to 180°C to generate organic vapors quantitatively. The major advantages of this technique are that no other measurement methods can be used to determine the generated organic concentrations in lieu of Method 25; and that the cartridge can easily be taken to the field for evaluation. The organic compounds generated in test runs are collected and analyzed using the Method 25 procedure. The generation of organics is quantitative and recoveries were found to be 100 ± 10%. The time required for desorption of the majority of organics is generally less than forty-five minutes at a flow rate of 100 mL/min; however, based on laboratory experience the recommended sampling time is sixty minutes. These spiked cartridges are stable at room temperature over a two-month period. Results of interlaboratory studies showed close agreement with the expected concentrations based on calculations from the mass loadings and sample volumes.