Laboratory evaluation of thermophilic-anaerobic digestion to produce Class A biosolids. 1. Stabilization performance of a continuous-flow reactor at low residence time.

There is increasing interest in the United States in producing biosolids from municipal wastewater treatment that meet the criteria for Class A designation established by the U.S. Environmental Protection Agency. Class A biosolids are intended to be free of pathogens and also must meet requirements for reduction of the vector-attraction potential associated with untreated sludge. High-temperature processes are considered to produce Class A biosolids if the combination of operating temperature and treatment time exceeds minimum criteria, but this option is not applicable to mixed, continuous-flow reactors. Such reactors, or any combination of reactors that does not meet the holding time requirement at a specific temperature, must be demonstrated to inactivate pathogens to levels consistent with the Class A criteria. This study was designed to evaluate pathogen inactivation by thermophilic anaerobic digestion in a mixed, continuous-flow reactor followed by batch or plug-flow treatment. In this first of a two-part series, we describe the performance of a continuous-flow laboratory reactor with respect to physical and chemical operating parameters; microbial inactivation in the combined continuous-flow and batch treatment system is described in the second part. Sludges from three different sources were treated at 53 degrees C, while sludge from one of the sources was also treated at 55 and 51 degrees C. Relatively short hydraulic retention times (four to six days) were used to represent a conservative operating condition with respect to pathogen inactivation. Treatment of a fermented primary sludge led to an average volatile-solids (VS) destruction efficiency of 45%, while VS destruction for the other two sources was near or below 38%, the Class A criterion for vector attraction reduction. Consistent with other studies on thermophilic anaerobic digestion of sludges at short residence times, effluent concentrations of volatile fatty acids (VFAs) were relatively high. Also consistent with other studies, the most abundant VFA in the effluent was propionate. Gas production ranged from 0.3 to 0.5 m3/kg VS fed and from 0.8 to 1.3 m3/kg VS destroyed.     

Laboratory evaluation of thermophilic-anaerobic digestion to produce Class A biosolids. 2. Inactivation of pathogens and indicator organisms in a continuous-flow reactor followed by batch treatment.

Thermophilic-anaerobic digestion in a single-stage, mixed, continuous-flow reactor is not approved in the United States as a process capable of producing Class A biosolids for land application. This study was designed to evaluate the inactivation of pathogens and indicator organisms in such a reactor followed by batch treatment in a smaller reactor. The combined process was evaluated at 53 degrees C with sludges from three different sources and at 51 and 55 degrees C with sludge from one of the sources. Feed sludge to the continuous-flow reactor was spiked with the pathogen surrogates Ascaris suum and vaccine-strain poliovirus. Feed and effluent were analyzed for these organisms and for indigenous Salmonella spp., fecal coliforms, Clostridium perfringens spores, and somatic and male-specific coliphages. No viable Ascaris eggs were observed in the effluent from the continuous reactor at 53 or 55 degrees C, with greater than 2-log removals across the digester in all cases. Approximately 2-log removal was observed at 51 degrees C, but all samples of effluent biosolids contained at least one viable Ascaris egg at 51 degrees C. No viable poliovirus was found in the digester effluent at any of the operating conditions, and viable Salmonella spp. were measured in the digester effluent in only one sample throughout the study. The ability of the continuous reactor to remove fecal coliforms to below the Class A monitoring limit depended on the concentration in the feed sludge. There was no significant removal of Clostridium perfringens across the continuous reactor under any condition, and there also was limited removal of somatic coliphages. The removal of male-specific coliphages across the continuous reactor appeared to be related to temperature. Overall, at least one of the Class A pathogen criteria or the fecal coliform limit was exceeded in at least one sample in the continuous-reactor effluent at each temperature. Over the range of temperatures evaluated, the maximum time required to meet the Class A criteria by batch treatment of the continuous-reactor effluent was 1 hour for Ascaris suum and Salmonella spp. and 2 hours for fecal coliforms.     

Surface Consolidation of Pentelic Marble: Criteria for the selection of methods and materials - The Acropolis case (6 pp)

Goal and Scope In order to realize surface consolidation of Pentelic marble on the Acropolis monuments, we have collected the criteria that have to be fulfilled by the methods and materials without side effects on the marbles (and other stones). When the existing methods and materials did not satisfy the requirements (criteria), we invented new ones.Methods The criteria were collected from the literature, by thermodynamic and kinetic viewpoints, by laboratory experiments and in situ observations on monuments, both in Greece and in several countries in which the various methods and materials were applied. Concerning our method of ‘Inversion of sulfation’, performed by spraying a K2CO3 solution, its concentration and its temperature were controlled in order to have a total inversion (certified by liquid crystals) of gypsum back to CaCO3. For the new material of ours, ‘Reinforced Lime’, in order to eliminate the disadvantages of plain lime (low carbonation rate, low mechanical properties of CaCO3 formed, lack of carbonation in the bulk of lime), measurements of the rate of carbonation were performed in plain lime and in lime with a different CaCO3 concentration beforehand as well as in a different CO2 environments, using DTG and XRD to measure the rate of carbonation. The detachment (kg/cm2) of marble specimens stuck by lime in each case was also measured. A microscope was also used to measure the dimensions of the grain in each case as well as ammonium citrate and thymolphthalein to certify the depth of carbonation in each case. Part of the work was communicated in an international congress.Results A table with the criteria of the selection of the methods and materials for the consolidation of Pentelic marble surfaces (and other stones) was established. None of the employed methods and materials fulfilled the criteria. Only the ‘Inversion of gypsum ‘ and the ‘Reinforced Lime’ were adopted and applied to the Acropolis monuments and to other monuments in Greece and in several other countries.Recommendation and Outlook All criteria must be used for the selection of methods and materials for the consolidation of the monument surfaces. This is why we have already studied with the same procedures, methods and materials for restoration, surface cleaning and protection.     

Endocrine disruption of water and sediment extracts in a non-radioactive dot blot/RNAse protection-assay using isolated hepatocytes of rainbow trout

Goal, Scope and Background In order to evaluate the estrogenic activity of sediments and XAD water extracts of selected sites of the catchment area of the River Neckar, a river system in Southern Germany, an integrative assessment approach was used to assess the ecological hazard potential of endocrine-disrupting compounds in sediment and water. Methods The approach is based on estrogen receptor-mediated vitellogenin synthesis induced in isolated hepatocytes of rainbow trout and quantified in a non-radioactive dot blot/RNAse protection-assay in parallel to comprehensive chemical analyses of estrogenic substances. Results and Discussion Numerous investigated extracts revealed an estrogen activity comparable to that of the positive control (1 nM 17?-estradiol corresponding to 270 ng/L in the test medium). Based on a concentration factor of 30 in the extracts and a recovery of XAD resins of approximately 80 %, 17?-estradiol equivalent concentrations between 20 and 26.7 ng/L could be calculated downstream of a sewage treatment plant (< 0.1 ng/L for a reference site). A comparison of the bioassay-derived Bio-TEQs (toxicity equivalents) and the Chem-TEQs revealed a high correlation with a Pearson coefficient of 0.85, indicating that the same ranking of the samples could be obtained with respect to the endocrine disrupting potential with both chemical and bioanalytical analysis. However, the TEQ concentrations computed from chemical analyses were significantly lower than the bioassay-derived TEQ concentrations. In fact, in none of the samples, more than 14 % of the vitellogenin-inducing potency could be attributed to the substances (steroids, alkylphenols, bisphenol A, diethylstilbestrol) analyzed. A comparison of the endocrine disrupting potential of sediments extracted by the solvents acetone and methanol revealed lower biological effects for acetone-extracted samples. Possible reasons may be a masking of endocrine effects in acetone extracts by cytotoxicity, a low extraction efficiency of the solvent acetone, or anti-estrogen potencies of some extracted sediment compounds. Using a mass balance approach, the contribution of the compounds analyzed chemically (Chem-TEQs) to the total endocrine activity (Bio-TEQs) was calculated. Based on the very low detection limits, particularly of the steroids with their high TEF factors, results revealed that a calculation of the Chem-TEQs is associated with considerable scale inaccuracy: Whereas only 7-15 % of the biological effectiveness (Bio-TEQs) could be explained by endocrine substances identified above the detection limits, the assumption of concentrations slightly below the given detection limits would result in a significant over estimation (137-197 %) of the Bio-TEQs. Even the interassay variation of the dot blot assay with different fish donors for primary hepatocyte (factor 2 - 2.5) is relatively low, when compared to the large range of the Chem-TEQ concentrations (factor 20) obtained when applying different modes of calculation. Conclusions and Outlook Overall, only a minor portion of the endocrine activity detected by bioassays could be linked to compounds identified by chemical analysis. In vitro assays for assessment of endocrine activities are useful as sensitive integrating methods that provide quantitative estimates of the total activity of particular receptor-mediated responses. Although discrepancies may also result from different bioanalytical approaches, it is overall likely that bioanalytical and not chemical analytical approaches give the correct estimate of endocrine disrupting potencies in environmental samples. As a conclusion, assessment of endocrine disruption based on chemical analysis alone does not appear sufficient and further research into the spectrum of substances with potential endocrine activity as well as into additive or even synergistic effects in complex environmental samples is urgently needed.     

Anaerobic incorporation of the radiolabeled explosive TNT and metabolites into the organic soil matrix of contaminated soil after different treatment procedures

Four bioreactor designs were performed to evaluate the level of incorporation of 14C-labeled 2,4,6-trinitrotoluene (TNT) and metabolites into the organic soil matrix of different anaerobically treated contaminated soils. The contaminated soils were amended with molasses slivers (80:20% per weight) as auxiliary substrate to enhance microbial activity. After 5 weeks (bioreactors 1 and 2), 8 weeks (bioreactor 3) and 12 weeks (bioreactor 4) of anaerobic incubation, we determined 41%, 58%, 72%, and 54%, respectively, of the initially applied radioactivity immobilized in various soil fractions. After alkaline hydrolyses of the solvent-extracted soils, low quantities of radiolabel were found in the humic and fulvic acid fractions, whereas the bulk of 14C activity was found to be strongly bound to the humin fraction (solid soil residues). The amounts of solvent extractable radioactivity were 53%, 40%, 16%, and 29% for bioreactors 1, 2, 3, and 4, respectively. The level of TNT transformation at the end of the experiments was within 90-94%. Regarding the results presented in this study, we can assume that there is the possibility of high incorporation levels of TNT metabolites into the soil organic matrix mediated by microbial cometabolism under strictly anoxic conditions.     

The evolution of mass balance models of persistent organic pollutant fate in the environment

Current approaches to modelling the fate of persistent organic pollutants (POPs) in the environment have evolved in response to four dominant characteristics of these substances; namely: (1) the presence of POPs in virtually all environmental phases and the ease with which they move from one to the other requires multi-compartmental modelling. Describing transport across phase boundaries becomes as, or even more, important as quantifying transport within the phases; (2) POPs may persist in the environment for many decades. For chemicals that 'have time', concepts such as equilibrium partitioning and steady-state become more important than for short-lived substances whose fate is more controlled by the rates of transformation; (3) measuring POPs is difficult and expensive and observed concentrations of POPs are not available in high spatial or temporal resolution. Consequently, high resolution tends not to be a high priority in POP models; and (4) detrimental effects of POPs often manifest themselves in top predators, which has led to a focus on modelling biotic uptake and transfer within food chains. The task of building a POPs model is viewed as combining the four 'building blocks' of partitioning, transport, transformation and source data with the help of the law of the conservation of mass. Process models, evaluative models, models of real local, regional and global fate, as well as biological uptake models are presented and references to numerous examples are provided. An attempt is made to forecast future directions in the field of POPs modelling. It is expected that modelling techniques that do not rely on quantitative emission estimates as well as approaches that take into account spatial, temporal and climatic variability as well as parameter uncertainty will increase in importance. Finally, the relationship between modelling POPs and models of other pollutant issues is addressed, as are potential interactions between POPs and pollutant issues such as eutrophication, acidification and global climate change.     

Tracing sources of atmospheric sulphur using epiphytic lichens

The overall objective of this work was to measure the spatial variation of sulphur isotopic composition of lichens across the island of Newfoundland in order to assess the degree to which the atmosphere is being affected by long-range transport of anthropogenic sulphur from eastern North America, and/or local pollution sources. A contour map (based on over 80 composite samples of the lichen Alectoria sarmentosa) illustrates the spatial distribution of sulphur isotopic composition of the Newfoundland atmosphere. It shows a gradient of delta(34)S of sulphur in lichen, decreasing from the coast to the interior of the island. It also shows local anomalies corresponding to the city of St. John's, the Come-By-Chance Oil Refinery, mining areas and fossil-fuel powered pulp and paper mills in central and western Newfoundland. The study strongly suggests that the isotopic composition of sulphur in the Newfoundland atmosphere is influenced more by the ocean (sea salt sulphate) and local anthropogenic activities in the province, than by long-range transport of continental North American sulphate.     

Short-term effects of metals on the filtration rate of the zebra mussel Dreissena polymorpha

In order to study the short-term ecotoxicity of metals to the freshwater mussel Dreissena polymorpha, the effects of Cu, Zn and Cd on the filtration rate of this mussel were determined in laboratory experiments. Filtration rate was chosen as the endpoint, because it is a sensitive sublethal parameter compared to mortality and it is an important parameter given the ecological role D. polymorpha fulfills. The filtration rate was calculated from the decrease in algal concentration, fed to mussels in aquaria, containing different metal concentrations. The EC50 for Cu (41 microg litre(-1)) was lower than for Cd (388 microg litre(-1)) and Zn (1350 microg litre(-1)). The NOEC(accumulation) for the essential metal Zn was higher than for the essential metal Cu. Cadmium, a non-essential metal, was accumulated at all elevated water concentrations, so the NOEC(accumulation) was the concentration in the control water (<0.2 microg litre(-1)). All (no) effect concentrations found in this study were above the quality criteria set for metal concentrations in Dutch surface water, suggesting that the zebra mussel is sufficiently protected by these quality criteria.     

Retrieval of heavy metal ions from solution via ferritisation

The paper summarises the results of the studies on retrieval of heavy metal ions in solution by ferritisation and its potential application in waste-water treatment. The optimum procedure for ferritisation of heavy metal ions in solution has been evolved with respect to pH, concentration of Fe2+, rate and time of aeration and temperature. The recommended procedure consists of controlled aeration of the solution containing heavy metal ions and ferrous ions at pH 9.5-10.5 at about 50 degrees C, until the black, granular, magnetic ferrite separates out. The metal ferrites can also be formed, even without heating or forced aeration, by ageing the mixed metal hydroxide precipitate at pH 10 to 11. The metal ferrites formed have been characterised by X-ray diffractometry. The laboratory-scope experiments conducted with synthetic heavy metal solutions as well as actual wastewater from a tanning industry showed that heavy metal ions can be effectively removed from solution to sub-ppm levels. The metal ferrites thus recovered may find commercial application as microwave absorbers, catalysts, metal scavengers, etc. This technique seems to have potential application in simultaneous, one step removal of different heavy metal ions from industrial wastewaters.     

Algal-bacterial interactions in metal contaminated floodplain sediments

The aim of the present study was to investigate algal-bacterial interactions in a gradient of metal contaminated natural sediments. By means of multivariate techniques, we related the genetic structure (denaturing gradient gel electrophoresis, DGGE) and the physiological structure (community-level physiological profiling, CLPP) of the bacterial communities to the species composition of the algal communities and to the abiotic environmental variables, including metal contamination. The results revealed that genetic and physiological structure of the bacterial communities correlated with the species composition of the algal community, but hardly to the level of metal pollution. This must be interpreted as an indication for a strong and species-specific linkage of algal and bacterial species in floodplain sediments. Metals were, however, not proven to affect either the algal or the bacterial communities of the Dutch river floodplains.