PVA降解菌的复配组合及其紫外诱变处理的研究

对已筛选出的4株PVA降解菌进行不同的组合后测定PVA降解率,发现Z5与Z8菌株混合后在1周内对PVA的去除率达到了所有组合中的最高值52.07%,比单菌株提高了约22%。采用紫外照射的方法对混合菌进行诱变并利用正交实验研究其特性,结果表明,诱变后的混合菌在1周内降解了91.46%的PVA,并且碳源浓度对酶活的影响最为显著。当pH为7,碳源、氮源含量分别为1.5 g/L、0.6 g/L,NaC l浓度为1.5 g/L时,诱变菌株处于最佳生长状态。     

Quantitative health risk assessment of inhalation exposure to automobile foundry dust

With a growing awareness of environmental protection, the dust pollution caused by automobile foundry work has become a serious and urgent problem. This study aimed to explore contamination levels and health effects of automobile foundry dust. A total of 276 dust samples from six types of work in an automobile foundry factory were collected and analysed using the filter membrane method. Probabilistic risk assessment model was developed for evaluating the health risk of foundry dust on workers. The health risk and its influencing factors among workers were then assessed by applying the Monte Carlo method to identify the most significant parameters. Health damage assessment was conducted to translate health risk into disability-adjusted life year (DALY). The results revealed that the mean concentration of dust on six types of work ranged from 1.67 to 5.40 mg/m³. The highest health risks to be come from melting, cast shakeout and finishing, followed by pouring, sand preparation, moulding and core-making. The probability of the risk exceeding 10⁻⁶ was approximately 85%, 90%, 90%, 75%, 70% and 45%, respectively. The sensitivity analysis indicated that average time, exposure duration, inhalation rate and dust concentration (C) made great contribution to dust health risk. Workers exposed to cast shakeout and finishing had the largest DALY of 48.64a. These results can further help managers to fully understand the dust risks on various types of work in the automobile foundry factories and provide scientific basis for the management and decision-making related to health damage assessment.

     

Recovery of Ni(II) from real electroplating wastewater using fixed-bed resin adsorption and subsequent electrodeposition

Resin adsorption and subsequent electrodeposition were used for nickel recovery. Treated wastewater can meet the Electroplating Pollutant Discharge Standard. The spent resin is completely regenerated by 3 BV of 4% HCl solution. 95.6% of nickel in concentrated eluent was recovered by electrodeposition. Effective recovery of high-value heavy metals from electroplating wastewater is of great significance, but recovering nickel ions from real electroplating wastewater as nickel sheet has not been reported. In this study, the pilot-scale fixed-bed resin adsorption was conducted to recover Ni(II) ions from real nickel plating wastewater, and then the concentrated Ni(II) ions in the regenerated solution were reduced to nickel sheet via electrodeposition. A commercial cation-exchange resin was selected and the optimal resin adsorption and regeneration conditions were investigated. The resin exhibited an adsorption capacity of 63 mg/g for Ni(II) ions, and the average amount of treated water was 84.6 bed volumes (BV) in the pilot-scale experiments. After the adsorption by two ion-exchange resin columns in series and one chelating resin column, the concentrations of Ni(II) in the treated wastewater were below 0.1 mg/L. After the regeneration of the spent resin using 3 BV of 4% (w/w) HCl solution, 1.5 BV of concentrated neutral nickel solution (>30 g/L) was obtained and used in the subsequent electrodeposition process. Using the aeration method, alkali and water required in resin activation process were greatly reduced to 2 BV and 3 BV, respectively. Under the optimal electrodeposition conditions, 95.6% of Ni(II) in desorption eluent could be recovered as the elemental nickel on the cathode. The total treatment cost for the resin adsorption and regeneration as well as the electrodeposition was calculated.     

Effects of pig manure containing copper and zinc on microbial community assessed via phospholipids in soils

Pig manure (PM) is widely used as an organic fertilizer to increase yields of crops. Excessive application of compost containing relatively great concentrations of copper (Cu) and zinc (Zn) can change soil quality. To clarify the effects of different rates of application and to determine the optimal rate of fertilization, PM containing 1,115 mg Cu kg^?1, dry mass (dm) and 1,497 mg Zn kg^?1, dm was applied to alkaline soil at rates of 0, 11, 22, 44, 88, and 222 g PM kg^?1, dm. Phospholipid fatty acids (PLFAs) were used to assess soil microbial community composition. Application of PM resulted in greater concentrations of total nitrogen (TN), NH₄ ⁺-N, NO₃ ^?-N, total carbon (TC), soil organic matter (SOM) but lesser pH values. Soils with application rates of 88–222 g PM kg^?1, dm had concentrations of total and EDTA-extractable Cu and Zn significantly greater than those in soil without PM, and concentrations of T-Cu and T-Zn in these amended soils exceeded maximum limits set by standards in china. Except in the soil with a rate of 11 g PM kg^?1, dm, total bacterial and fungal PLFAs were directly proportional to rate of application of PM. Biomasses of bacteria and fungi were significantly greater in soils with application rates of 44–222 g PM kg^?1, dm than in the soil without PM. SOM, TC and EDTA-Zn had the most direct influence on soil microbial communities. To improve fertility of soils and maintain quality of soil, rate of application should be 22–44 g PM kg^?1 dm, soil containing Cu and Zn.     

石化行业给排水系统设计图纸环境监理审查要点

石化行业废水种类多样、毒性较大,给排水系统的设计会直接影响石化项目建成后周边地表及地下水环境质量。设计文件的环保审查是环境监理的重要依据之一,其中,相关的设计图纸对下一步建设工作具有指导作用,是所有施工单位的施工依据。以某石化行业为例,对给排水系统设计文件的收集进行了分析,并根据设计图纸环保审查中存在的问题,对环境监理如何提高在设计会审中的作用,设计阶段如何对设计图纸进行审查以及审查的重点内容等进行了阐述。     

三燃式危险废物焚烧技术探讨

文章介绍了三燃式危险废物焚烧技术,该新型焚烧炉采用回转热解窑作为一次燃烧处理方式,再由往复式炉排炉进行二次焚化燃烧,未燃尽的气体、粉尘进入三燃室充分分解燃烧,因此烧尽率高、热能效率高.     

Photodegradation of azithromycin in various aqueous systems under simulated and natural solar radiation: kinetics and identification of photoproducts

This article describes the photolysis of azithromycin, a macrolide antibiotic with reported occurrence in environmental waters, under simulated solar radiation. The photodegradation followed first-order reaction kinetics in five matrices examined. In HPLC water, the degradation rate was the slowest (half-life: 20 h), whereas in artificial freshwater supplemented with nitrate (5 mg L⁻¹) or humic acids (0.5 mg L⁻¹) the degradation of azithromycin was enhanced by factors of 5 and 16, respectively, which indicated the role of indirect photolysis involving the formation of highly reactive species. Following chromatographic separation on a UPLC system, the characterization of the transformation products was accomplished using high-resolution QqToF-MS analysis. The presence of seven photoproducts was observed and their formation was postulated to originate from (bis)-N-demethylation in the desosamine sugar, O-demethylation in the cladinose sugar, combinations thereof, as well as from hydrolytic cleavages of the desosamine and/or cladinose residue. Two of these photoproducts could also be detected in natural photodegradation process in river water which was spiked with azithromycin.     

烟气NO氧化催化剂Cu-V/Ti-PILCs的制备及其硫水稳定性

采用等体积浸渍法制备了以钛交联粘土为载体,Cu与V氧化物为活性组分的烟气NO氧化催化剂(Cu-v/Ti-PILCs),并考察了各种制备条件下催化剂的活性及稳定性.结果显示,当V水/V丙酮 =1∶2,负载4%CuO和2%V2O5,并在500℃煅烧时制得的Cu-V/Ti-PILCs催化剂,在NO浓度为350 mg/m3,O...     

粗MnSO4溶液中MnS2O6的去除条件研究

用软锰矿吸收SO2生成MnSO4时会伴随有副产物MnS2O6生成。产品中MnS2O6的存在会降低硫酸锰产品质量,同时会缓慢释放出SO2气体污染环境。本文用单因素实验方法研究了粗MnSO4溶液中MnS2O6的最优去除条件。研究结果显示,软锰矿用量为12.2 g,硫酸加入量为20 mL、反应温度100℃、反应时间3 h、搅拌速度500 r/min,MnS2O6的去除率可达91%以上。其最终产品能达到GB1622-1986一级品标准。     

密封充氢环境条件下固态电化学氢气传感器效应试验研究

目的研究密闭充氢环境下固态电化学氢气传感器效应。方法设计能模拟低氧、低氢和压力变化的密闭充氢环境,并在此环境中进行一系列氢气传感器效应试验,分析、评定试验数据。结果得到了不同环境下氢气、氧气浓度随时间变化的规律,提出固态电化学氢气传感器的有效工作环境,并预测了其在不同贮存环境下的工作寿命。结论密闭充氢环境内压力和温度的变化对固态电化学氢气传感器影响较大,湿度影响较小,注气检定合格的氢气传感器,在密封容器内扩散式检定,不合格率高,检定数据误差大于±5%FS。