内质网应激在氟暴露致小鼠睾丸损伤中的作用

探讨了内质网应激在亚慢性氟暴露致小鼠睾丸损伤中的作用及分子机制.选用健康初断乳ICR雄性小鼠30只,随机分为对照组（C）、低氟组（LF）和高氟组（HF）,分别饮用自来水、5、30 mg·L^-1氟化钠水溶液90 d.亚慢性氟暴露结束后,以睾丸脏器系数、睾丸组织氧化/抗氧化酶和形态结构、精子质量、睾丸细胞凋亡、葡萄糖调节蛋白78（GRP78）、CCAAT/增强子结合蛋白同源蛋白（CHOP）、半胱氨酸天冬氨酸蛋白酶12（CASPASE-12）、半胱氨酸天冬氨酸蛋白酶3（CASPASE-3）为观测点.结果表明,与对照组比,LF组和HF组LDH、SOD、T-AOC活性下降,MDA含量上升,HF组GSH-PX活性下降,差异有统计学意义（p<0.05或p<0.01）;LF组可见细胞层次减少、间隙变大,成熟精子数量减少,HF组细胞溶解、层次紊乱,空泡化严重,少见成熟精子;LF组和HF组小鼠的精子活力降低,HF组小鼠精子数量下降,畸形率上升,差异有统计学意义（p<0.05或p<0.01）;LF组和HF组睾丸细胞凋亡指数上升,差异有统计学意义（p<0.01）;LF组和HF组Grp78、Caspase-12、Caspase-3基因表达水平上升,差异有统计学意义（p<0.05或p<0.01）.结果提示,除氧化应激以外,Caspase-12和Caspase-3基因表达异常可能是氟暴露致小鼠睾丸细胞凋亡异常的分子机制之一.     

基于AIS轨迹修复的船舶排放空间表征改进方法与应用

基于船舶自动识别系统（Automatic Identification System,AIS）数据表征船舶排放是目前船舶排放空间表征的主流方法,但AIS船舶轨迹点缺失会造成船舶排放量低估和船舶空间分布表征错误,进而影响船舶排放控制区的划分.为改进船舶排放空间表征,本研究以2013年广东省AIS船舶数据为例,采用基于时间和经纬度的三次样条方法对AIS船舶轨迹进行修复,结合动力法计算船舶排放,分析对比AIS轨迹修复前后船舶排放表征的差异,并利用空气质量模型和卫星观测评估AIS轨迹修复对船舶排放表征和广东沿海空气质量模拟的改进效果.结果表明：轨迹修复后广东省海域船舶轨迹点总数由4685773个增至5746664个,船舶NO_x排放量增加了0.6%.对于轨迹点与排放缺失集中的粤东海域,轨迹修复后船舶轨迹点数增加了88%,NO_x排放量在广东省船舶排放量的占比提升至22%,特别是在粤东重点修复海域NO_x排放量增加了2.7倍.原始轨迹在广东省海域较为稀疏,在粤东海域有明显轨迹缺失;轨迹修复后广东省海域船舶轨迹更为密集,粤东海域船舶轨迹得以补充,船舶排放空间分布更连贯.对比模拟结果与卫星观测结果,轨迹修复后粤东重点修复海域船舶模拟浓度与观测浓度的偏差由51%减至6%,总体上船舶排放模拟结果更接近卫星观测结果.     

金属改性对SAPO-34低温还原NO性能的影响

采用浸渍法制备金属改性SAPO-34分子筛催化剂,分析比较了不同单金属（Cu或Co）及不同比例双金属（Cu：Co=1：1、3：1、5：1,质量比）改性催化剂对NO的催化还原性能,评价了不同催化剂的N₂选择性,并采用扫描电子显微镜（SEM）、比表面积测试、X射线衍射分析（XRD）、NH₃-程序升温脱附（NH₃-TPD）等表征手段对催化剂的物化性能进行了分析.结果表明,单金属Cu改性催化剂具有较宽的温度区间,在250~450℃范围内NO的转化率始终保持在100%;双金属改性使NO转化率保持为100%的最低温度下降了25~50℃,显著拓宽了低温段窗口,其中,Cu₃Co₁/SAPO-34催化剂的低温催化还原性能最好,200℃即可实现100%的NO转化率,175℃下的转化率也高达80%以上.Cu-Co双金属改性SAPO-34分子筛催化剂具有优异的低温催化还原NO性能,具有在机动车尾气、工业废气的低温脱硝治理领域应用的潜力.     

核壳结构KNbO3@Co(OH)2的制备及其活化过一硫酸盐降解帕珠沙星的研究

制备了以KNbO₃为载体材料的Co（OH）₂复合材料并对其进行了详细的表征,分析了材料的组成成分、组成形态进而确定了其为核壳结构形貌的KNbO₃@Co（OH）₂.利用合成的样品作为催化剂活化过一硫酸盐（peroxymonosulfate,PMS）来降解帕珠沙星（pazufloxacin,PZF）,结果表明制备的催化剂对PZF的去除效率显著增加.讨论了不同初始PMS剂量对降解效率的影响,发现随着PMS增加可活化生成更多的硫酸根自由基（sulfate radicals,SO₄^·-）和羟基自由基（hydroxyl radicals,HO^·）来降解PZF,但继续增大PMS用量降解效率未见明显提升.酸性和中性pH值条件下利于反应活化PMS降解PZF,而碱性体系减缓反应,甚至强碱体系更易形成Co（OH）₂沉淀不利于反应体系中活性组分CoOH⁺的形成,大大抑制了催化性能.此外,在体系中加入淬灭剂叔丁醇（tert-Butanol,TBA）或者乙醇（ethanol,ETOH）进行自由基的淬灭实验,结果表明SO₄^·-自由基为体系降解PZF过程中主要贡献的自由基,而HO^·自由基的贡献较少.催化剂具有较好的稳定性5次循环之后仍能在10 min之内完全去除PZF.本研究提出了新的思路为制备其他载体的Co（OH）₂核壳结构提供参考依据,同时将该催化剂结合高级氧化技术应用到水体新兴有机污染物净化领域具有很好的应用前景.     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

Dynamic nano-Ag colloids cytotoxicity to and accumulation by Escherichia coli: Effects of Fe3+, ionic strength and humic acid

Released Ag ions or/and Ag particles are believed to contribute to the cytotoxicity of Ag nanomaterials, and thus, the cytotoxicity and mechanism of Ag nanomaterials should be dynamic in water due to unfixed Ag particle:Ag⁺ ratios. Our recent research found that the cytotoxicity of PVP-Ag nanoparticles is attributable to Ag particles alone in 3 hr bioassays, and shifts to both Ag particles and released Ag⁺ in 48 hr bioassays. Herein, as a continued study, the cytotoxicity and accumulation of 50 and 100 nm Ag colloids in Escherichia coli were determined dynamically. The cytotoxicity and mechanisms of nano-Ag colloids are dynamic throughout exposure and are derived from both Ag ions and particles. Ag accumulation by E. coli is derived mainly from extracellular Ag particles during the initial 12 hr of exposure, and thereafter mainly from intracellular Ag ions. Fe³⁺ accelerates the oxidative dissolution of nano-Ag colloids, which results in decreasing amounts of Ag particles and particle-related toxicity. Na⁺ stabilizes nano-Ag colloids, thereby decreasing the bioavailability of Ag particles and particle-related toxicity. Humic acid (HA) binds Ag⁺ to form Ag⁺-HA, decreasing ion-related toxicity and binding to the E. coli surface, decreasing particle-related toxicity. HA in complex conditions showed a stronger relative contribution to toxicity and accumulation than Na⁺ or Fe³⁺. The results highlighted the cytotoxicity and mechanism of nano-Ag colloids are dynamic and affected by environmental factors, and therefore exposure duration and water chemistry should be seriously considered in environmental and health risk assessments.     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

Particulate matter exchange between atmosphere and roads surfaces in urban areas

The deposition and the re-suspension of particulate matter (PM) in urban areas are the key processes that contribute not only to stormwater pollution, but also to air pollution. However, investigation of the deposition and the re-suspension of PM is challenging because of the difficulties in distinguishing between the resuspended and the deposited PM. This study created two Bayesian Networks (BN) models to explore the deposition and the re-suspension of PM as well as the important influential factors. The outcomes of BN modelling revealed that deposition and re-suspension of PM10 occurred under both, high-traffic and low-traffic conditions, and the re-suspension of PM2.5 occurred under low-traffic conditions. The deposition of PM10 under low-volume traffic condition is 1.6 times higher than under high-volume traffic condition, which is attributed to the decrease in PM10 caused by relatively higher turbulence under high-volume traffic conditions. PM10 is more easily resuspended from road surfaces compared to PM2.5 as the particles which larger than the thickness of the laminar airflow over the road surface are more easily removed from road surfaces. The increase in wind speed contributes to the increase in PM build-up by transporting particulates from roadside areas to the road surfaces and the airborne PM2.5 and PM10 increases with the increase in relative humidity. The study outcomes provide a step improvement in the understanding of the transfer processes of PM2.5 and PM10 between atmosphere and urban road surfaces, which in turn will contribute to the effective design of mitigation measures for urban stormwater and air pollution.