Food waste impact on municipal solid waste angle of internal friction

The impact of food waste content on the municipal solid waste (MSW) friction angle was studied. Using reconstituted fresh MSW specimens with different food waste content (0%, 40%, 58%, and 80%), 48 small-scale (100-mm-diameter) direct shear tests and 12 large-scale (430 mm × 430 mm) direct shear tests were performed. A stress-controlled large-scale direct shear test device allowing approximately 170-mm sample horizontal displacement was designed and used. At both testing scales, the mobilized internal friction angle of MSW decreased considerably as food waste content increased. As food waste content increased from 0% to 40% and from 40% to 80%, the mobilized internal friction angles (estimated using the mobilized peak (ultimate) shear strengths of the small-scale direct shear tests) decreased from 39° to 31° and from 31° to 7°, respectively, while those of large-scale tests decreased from 36° to 26° and from 26° to 15°, respectively. Most friction angle measurements produced in this study fell within the range of those previously reported for MSW.     

Online sorting of recovered wood waste by automated XRF-technology. Part I: detection of preservative-treated wood waste

Waste wood is frequently contaminated with wood treatment preservatives including chromated copper arsenate (CCA) and alkaline copper quat (ACQ), both of which contain metals which contaminate recycled wood products. The objective of this research was to propose a design for online automated identification of As-based and Cu-based treated wood within the recovered wood waste stream utilizing an X-ray fluorescence (XRF) system, and to evaluate the detection parameters of such system. A full-scale detection unit was used for experimentation. Two main parameters (operational threshold (OT) and measurement time) were evaluated to optimize detection efficiencies. OTs of targeted metals, As and Cu, in wood were reduced to 0.02 and 0.05, respectively. The optimum minimum measurement time of 500 ms resulted in 98%, 91%, and 97% diversion of the As, Cu and Cr mass originally contained in wood, respectively. Comparisons with other detection methods show that XRF technology can potentially fulfill the need for cost-effective processing at large facilities (>30 tons per day) which require the removal of As-based preservatives from their wood waste stream.     

A Method for Comparative Analysis of Recovery Potential in Impaired Waters Restoration Planning

Common decision support tools and a growing body of knowledge about ecological recovery can help inform and guide large state and federal restoration programs affecting thousands of impaired waters. Under the federal Clean Water Act (CWA), waters not meeting state Water Quality Standards due to impairment by pollutants are placed on the CWA Section 303(d) list, scheduled for Total Maximum Daily Load (TMDL) development, and ultimately restored. Tens of thousands of 303(d)-listed waters, many with completed TMDLs, represent a restoration workload of many years. State TMDL scheduling and implementation decisions influence the choice of waters and the sequence of restoration. Strategies that compare these waters’ recovery potential could optimize the gain of ecological resources by restoring promising sites earlier. We explored ways for states to use recovery potential in restoration priority setting with landscape analysis methods, geographic data, and impaired waters monitoring data. From the literature and practice we identified measurable, recovery-relevant ecological, stressor, and social context metrics and developed a restorability screening approach adaptable to widely different environments and program goals. In this paper we describe the indicators, the methodology, and three statewide, recovery-based targeting and prioritization projects. We also call for refining the scientific basis for estimating recovery potential.

The Effectiveness of Contrasting Protected Areas in Preventing Deforestation in Madre de Dios, Peru

Accurate monitoring of the effectiveness of protected areas (PAs) in decreasing deforestation is increasingly important given the vital role of forest protection in climate change mitigation. Recent studies on PA effectiveness have used remote-sensing imagery to compare deforestation rates within PAs to surrounding areas. However, remote-sensing data used in isolation provides limited information on the factors contributing to effectiveness. We used landscape-modelling techniques to estimate the effectiveness of ten PAs in Madre de Dios, Peru. Factors influencing PA effectiveness were investigated using in situ key-informant interviews. Although all of the PAs studied had positive effectiveness scores, those with the highest scores were ecotourism and conservation concessions, where monitoring and surveillance activities and good relations with surrounding communities were reported as possible factors in decreasing deforestation rates. Native community areas had the lowest scores, with deforestation mainly driven by internal resource use and population growth. Weak local governance and immigration were identified as underlying factors decreasing the effectiveness of protection, whereas good relations with surrounding communities and monitoring activity increased effectiveness. The results highlight the need to combine remote sensing with in situ information on PA management because identification of drivers and deterrents of deforestation is vital for improving the effectiveness of protection.     

Effect of pH on surface characteristics of switchgrass-derived biochars produced by fast pyrolysis

Surface properties of switchgrass-derived biochars produced at fast pyrolysis temperatures of 450, 600 and 800 °C were characterized at different solution pHs in order to determine the structural and chemical changes of artificially-weathered biochars when incorporated into soil. As biochars were acidified from pH 7 to 3, crystalline minerals dissolved slowly releasing nutrients; however, residual minerals were still detected in biochars produced at higher pyrolysis temperatures after pH treatment. Moreover, the amount of exchangeable bases and other inorganic compounds released from the biochars increased when pH decreased. As minerals dissolved from the biochars, total surface area and pore volume were found to increase. Surface functional groups and water vapor adsorption capacity at 0.8 P/P_o also increased, whereas the potential CEC of biochars decreased due to the replacement of exchangeable sites by hydrogen ion. Therefore, during the aging process, it is predicted that soil-incorporated biochars will slowly release nutrients with changes in surface functionality and porosity, which are expected to enhance water holding capacity of soil and provide a beneficial habitat for microbial colonization.     

Responses of Hybrid Poplar Trees to Sulfur Dioxide Fumigation

This paper verifies the presence of significant interclonal variation in the tolerance of hybrid poplar (Populus deltoides Bartr. cv. Angulata × P. trichocarpa Torr. and Gray) to sulfur dioxide fumigation. Rooted stem cuttings of four hybrid poplar clones were exposed to 5 ppm sulfur dioxide for 0, 3, 6, 9, or 12 hours in controlled environment chambers. Multivariate analyses were made from the shoot growth measurements recorded for 4 weeks before and after fumigation and on the data of foliar injury induced by sulfur dioxide. The following factors were statistically significant in determining growth response and foliar injury: (1) genotype; (2) duration of treatment; and (3) interaction between genotype and hours of fumigation. All partial correlations between foliar injury and subsequent shoot growth were positive and significant. Sufficient genetic variation appears to exist in this Populus hybrid to encourage selection of clones tolerant to short-term exposures of high levels of sulfur dioxide.     

Recovery of an Aqueous Iron Phosphating/ Degreasing Bath by Ultrafiltration

Aqueous cleaners are emerging as safe and effective alternatives to solvent degreasers, but switching to water-based cleaners may create a new waste which is high in oil and grease and potentially RCRA hazardous. In the case study summarized here, one metal fabricator replaced a trichloroethylene degreaser with an aqueous iron phosphating/degreasing bath to clean and precondition steel parts. The aqueous bath typically lasted three to four months, until the buildup of oil in the tank began to sacrifice product quality and raise oil and grease levels in the rinse water discharge. Hauling away and replacing the spent cleaner resulted in more than 15,000 gallon/year of hazardous waste.

Ultrafiltration was selected as the most promising technology to recycle the aqueous cleaner and thereby reduce hazardous waste generation. Following pilot-scale testing at the Illinois Hazardous Waste Research and Information Center, on-site full-scale testing integrated the new waste reduction scheme directly into the facility’s production process. Ultrafiltration continuously filtered and returned clean process solution back to the iron phosphating/degreasing bath during normal plant operation, substantially reducing and maintaining oil concentrations at acceptable operating levels. The new process design successfully reduced hazardous waste generation 99.8 percent with a payback period of only 6.9 months.