Leachate injection using vertical wells in bioreactor landfills

Leachate recirculation or liquid injection in municipal solid waste landfills offers economic and environmental benefits. The key objective of this study was to carry out numerical evaluation of key design variables for leachate recirculation system consisting of vertical wells. In order to achieve the objective, numerical modeling was carried out using the finite-element model HYDRUS-2D. The following design parameters were evaluated by simulating liquid pressure head on the liner and the wetted width of the waste under steady-state flow conditions: (1) hydraulic conductivities of the waste and vertical well backfill; (2) liquid injection rate and dosing frequency; (3) well diameter, screen height and screen depth; and (4) hydraulic conductivity of the leachate collection system, slope of the leachate collection system and spacing of the leachate collection pipes. The key findings of this study are as follows. The well diameter, hydraulic conductivity of the well drainage pack, and screen height and screen depth of the well have very little effect on the wetted width for a given liquid flux. The wetted width and the injection pressure for a given liquid flux decrease with the increase in the hydraulic conductivity of the waste. The pressure head on the liner increases with the decrease in the vertical distance between the bottom of the well screen and the top of leachate collection system. The liquid injection flux increases with the decrease in hydraulic conductivity of the leachate collection system. Unlike sand (k approximately 10(-4)m/s), pea gravel (k approximately 0.01 m/s) resulted in less than 0.3m pressure head on the liner for all simulations carried out in this study.     

Leachate recirculation effects on waste degradation: study on columns

The purpose of this study is to determine the impact of leachate recirculation on the degradation of municipal solid wastes (bioreactor concept). The study was carried out using columns containing approximately 50 kg of waste, in order to follow waste degradation over a limited time. Three types of waste were studied: fresh waste of standard composition, fresh waste of fermentable composition and some 8-yr-old waste extracted from a site in France. Measurement of the global parameters, such as chemical oxygen demand (COD), volatile acidity, alkalinity, leachate conductivity, methane potential of the wastes and biogas production monitoring (volume of CO2 and CH4 produced), were carried out. The quantity of oxydizable matter and biogas production was increased by the leachate recirculation, and the duration of the first degradation phases was reduced in all cases. Chloride, ammonium and organic pollution accumulation was observed according to the duration of recirculation. After 400 days of degradation, waste stabilization seemed to be reached for all of the recirculated columns (COD<300 mg/L O2, and methane potential reached).     

Do differences between metal body residues reflect the differences between effects for Chironomus riparius exposed to different sediments?

Sediment characteristics are well known to interfere with toxicity, mainly through differences in terms of bioaccumulation. Here, with chironomids exposed to zinc in an artificial and a field sediment, we investigated the differences of zinc accumulation and of effects on the life cycle, at individual and population level. We used biology and energy-based modeling to analyze the data at all the levels of biological organization. This permits a reliable estimation of thresholds values for tissue residues. Differences in zinc tissue residues accounted for most of the differences between the results for both sediments (a factor of 11 for differences from 20 to 100 depending on the parameter which is considered). Taking into account accumulation and background variability, the differences relative to thresholds could be accounted for. However, it appeared that, once the threshold was passed, effects were much more pronounced for organisms exposed to artificial sediment compared to field sediment. We concluded that some sediment characteristics can enhance toxicity, in addition to their influence on the compound accumulation, even if the latter was the major source of differences in our study.     

The influence of radical architecture on cadmium bioaccumulation in the black mangrove, Avicennia germinans L

Two groups of Avicennia germinans plants with differences in the radical architecture were exposed under hydroponic conditions to 95ppm of cadmium (Cd) for a period of 24h. Later, Cd concentration in roots, stems and leaves was determined by graphite furnace atomic absorption spectrophotometry. Our results showed that, for both groups of plants, the roots accumulated higher concentration of Cd as compared to stems and leaves, though, the plants of group B displayed enhanced radical architecture, better growth performance, and lower Cd concentration as compared to plants of group A. In contrast, low values of leaves/roots Cd transportation index, and bioaccumulation factor were found in plants of group B. These results suggest that the higher radical architecture developed in plants of group B might better adjust the uptake of Cd as a result of an integrated network of multiple response processes for instances, production of organic acids, antioxidative replay, cell-wall lignification and/or suberization. Further studies will be focused in understanding the role of the radical system in mangrove plants with the rhizosphere activation and root adsorption to soil Cd under natural conditions.     

Oxidation of trichloroethene over metal oxide catalysts: kinetic studies and correlation with adsorption properties

The performance of bulk chromium oxide is compared with that of a Mn commercial catalyst for the deep oxidation of trichloroethene (1000-2500ppmv, 55h(-1) space velocity) in air, in dry and wet (20000ppm of H(2)O) conditions, in terms of activity, selectivity and stability. Chromium oxide was found to be more active (on a catalyst weight basis), however its activity decreases continuously with time on stream. The presence of water increases its stability, the Mn catalyst showing the opposite behaviour. The effect of water on the Cr catalyst can be explained according to the Deacon equilibrium, as the presence of water tends to decrease the Cl(2) concentration, assumed to be responsible of the catalyst deactivation. Regarding to the selectivity, the Mn catalyst yields C(2)Cl(4), CCl(4) and CHCl(3) as organochlorinated by-products, whereas chromium oxide produces only trace amounts of CCl(4). Simple power-law kinetics expressions (first-order for Mn and zero-order for Cr) provide fairly good fits for the evolution of the conversion with the temperature. Furthermore, the kinetic behaviour of chromium oxide can be represented with a Langmuir-Hinshelwood model taking into account the chlorine inhibitory effect.     

Atrazine sorption and fate in a Ultisol from humid tropical Brazil

This study combined laboratory based microcosm systems as well as field experiments to evaluate the mobility of atrazine on a Ultisol under humid tropical conditions in Brazil. Results from sorption experiments fit to the Freundlich isotherm model [K(f) 0.99 mg kg(-1)/(mg l(-1))(1/n)], and indicate a low sorption capacity for atrazine in this soil and consequently large potential for movement by leaching and runoff. Microcosm systems using (14)C-atrazine to trace the fate of the applied herbicide, showed that 0.33% of the atrazine was volatilized, 0.25% mineralized and 6.89% was recorded in the leachate. After 60 d in the microcosms, 75% of the (14)C remained in the upper 5 cm soil layer indicating atrazine or its metabolites remained close to the soil surface. In field experiments, after 60 d, only 5% of the atrazine applied was recovered in the upper soil layers. In the field experiments atrazine was detected at a depth of 50 cm indicating leaching. Simulating tropical rain in field experiments resulted in 2.1% loss of atrazine in runoff of which 0.5% was adsorbed onto transported soil particles and 1.6% was in solution. Atrazine runoff was greatest two days after herbicide application and decreased 10 fold after 15 d. The use of atrazine on Ultisols, in the humid tropics, constitutes a threat to water quality, causing surface water and ground water pollution.     

Biosurfactant technology for remediation of cadmium and lead contaminated soils

This research focuses on column experiments conducted to evaluate the potential of environmentally compatible rhamnolipid biosurfactant produced by Pseudomonas aeruginosa strain BS2 to remove heavy metals (Cd and Pb) from artificially contaminated soil. Results have shown that di-rhamnolipid removes not only the leachable or available fraction of Cd and Pb but also the bound metals as compared to tap water which removed the mobile fraction only. Washing of contaminated soil with tap water revealed that approximately 2.7% of Cd and 9.8% of Pb in contaminated soil was in freely available or weakly bound forms whereas washing with rhamnolipid removed 92% of Cd and 88% of Pb after 36 h of leaching. This indicated that di-rhamnolipid selectively favours mobilization of metals in the order of Cd>Pb. Biosurfactant specificity observed towards specific metal will help in preferential elution of specific contaminant using di-rhamnolipid. It was further observed that pH of the leachates collected from heavy metal contaminated soil column treated with di-rhamnolipid solution was low (6.60-6.78) as compared to that of leachates from heavy metal contaminated soil column treated with tap water (pH 6.90-7.25), which showed high dissolution of metal species from the contaminated soil and effective leaching of metals with treatment with biosurfactant. The microbial population of the contaminated soil was increased after removal of metals by biosurfactant indicating the decrease of toxicity of metals to soil microflora. This study shows that biosurfactant technology can be an effective and nondestructive method for bioremediation of cadmium and lead contaminated soil.     

Modelling of PCDD/F release from MSW bio-drying

In the present work, an experimentation was carried out to study the behaviour of PCDD/F during the process of municipal solid waste (MSW) bio-drying. This process belongs to the biological mechanical treatment (BMT) options and is aimed to the dewatering of MSW thanks to the biological exothermal reactions (thermal drying, on the contrary, needs an external heat source as methane). The result is a decrease of waste weight and an increase of lower heating value (as the energy content refers to a lower amount of waste). Of course, the overall energy availability does not increase, but the characteristics of bio-drying are interesting as a way for refuse derived fuel generation: glass, metals and inert removals are easier after bio-drying. The literature of the sector shows only few data on PCDD/F emission to air from BMT. Anyway, in the present work an original theory has been put forward in order to explain the enrichment of PCDD/F in the air exiting the biological processes. The role of the initial PCDD/F concentration in the ambient air entering the plant is obviously taken into account. The results of the developed experimentation and the following elaborations point out that PCDD/F could be freed from the volatile solids consumed during the process. The different amount of PCDD/F in the waste and the different consumption of volatile solids depending on the biological process can explain the different PCDD/F emission factors available in the literature.     

Algal-bacterial interactions in metal contaminated floodplain sediments

The aim of the present study was to investigate algal-bacterial interactions in a gradient of metal contaminated natural sediments. By means of multivariate techniques, we related the genetic structure (denaturing gradient gel electrophoresis, DGGE) and the physiological structure (community-level physiological profiling, CLPP) of the bacterial communities to the species composition of the algal communities and to the abiotic environmental variables, including metal contamination. The results revealed that genetic and physiological structure of the bacterial communities correlated with the species composition of the algal community, but hardly to the level of metal pollution. This must be interpreted as an indication for a strong and species-specific linkage of algal and bacterial species in floodplain sediments. Metals were, however, not proven to affect either the algal or the bacterial communities of the Dutch river floodplains.     

Lichen and moss bags as monitoring devices in urban areas. Part II: trace element content in living and dead biomonitors and comparison with synthetic materials

Lobes of the lichen Pseudevernia furfuracea (L.) Zopf and shoots of the moss Hypnum cupressiforme Hedw. were subjected to different treatments (water washing, oven drying, HNO3 washing, NH4-oxalate extraction) to assess the influence of vitality on accumulation efficiency, during a 6-week exposure in bags in two Italian cities, Trieste and Naples. No trend emerged between treatments, in terms of accumulation ability, for major and trace elements. Only water-washed lichens showed an increased C and N content after exposure in both cities. Element concentrations generally reached higher values in mosses than in lichens, especially for Al, Fe, and Zn (both cities), and for Cu, Mg and Na (Naples). Surface development strongly influenced accumulation capacity of the biomonitors. Quartzose and cation exchange filters revealed, on a weight basis, a poor performance. In urban environments, surface interception of atmospheric particulate seems to play a major role in accumulation, irrespective of organism vitality.