The occurrence of disinfection by‐products in Taiwan drinking water

In this study, samples were taken from six conventional water treatment plants for disinfection by‐products analysis. Results from the analysis revealed that trihalomethanes (THMs) concentrations in all samples were below regulatory levels (100 μg/L). Although the national standard for haloacetic acids (HAA5) has not yet been promulgated in Taiwan, samples from two water plants contained HAA5 concentrations exceeding the USEPA limit (MCL of HAA5 of Stage 1, 60 μg/L). THMs and HAA5 were found to be the major disinfection by‐products in all water treatment plants. It was noted that the concentration of HAA5 in most samples was higher than that of the trihalomathanes. However, the formation potential of THM (THMFP) was found to be higher than that of HAA (HAAFP). Good correlation also was found between THMFP (or THMFP) and HAA5 (or THMs). In evaluating the performance of the treatment processes, it was found that conventional water treatment processes followed by activated carbon were effective in removing disinfection by‐products (DBPs) from source water with pre‐ozonation. The treatment processes were at their optimum performance in removing contaminants when O₃/TOC₀ was held at 0.75.     

Assesment of disinfection by‐products removal by ozonation coupled with adsorption

This research work was performed to evaluate ozonation and granular activated carbon adsorption processes from the view‐point of controlling the formation of disinfection by products (DBPs). Both the humic acid and raw water were first preozonated and then adsorbed on the activated carbon to assess the potency for removal of total organic carbon (TOC) and DBPs. The disinfection by‐product including THMs and HAAs, in principle, can be successfully removed through a use of the ozonation and granular activated carbon (GAC) adsorption processes. However, in practice dealing with the raw water, it is necessary to introduce the pilot‐plant to obtain the design and operation guidelines for the water treatment plant through the ICA (Instrumentation Control and Automation) program in our future research work.     

基于改进序关系法的北京市水资源可持续利用评价

指标权重的确定是水资源综合评价工作的基础.前期的研究多采用单一的权重确定方法,致使评价结果存在差异.论文提出改进序关系法来确定指标权重,通过构建北京市水资源可持续利用评价指标体系,利用Spearman 检验淘汰不通过一致性检验的专家指标排序,并运用循环修正的思路统一指标重要程度排序,最后通过相邻两个指标的标准差比值确定指标间的重要性比率,建立了基于改进序关系法的水资源可持续利用评价模型,并对北京市2005—2010年的水资源可持续利用状况进行评价.研究结果表明,通过改进序关系法确定指标权重,使得组合权重体现专家意见和指标数据信息,主客观权重分配的问题也得到了较好的解决.     

Characteristics of road dust from different sampling sites in northern Taiwan

Road dust contributes a large percentage of the atmosphere's suspended particles in Taiwan. Three road dust samples were collected from downtown, electrical park, and freeway tunnel areas. A mechanical sieve separated the road dust in the initial stage. Particles > 100 microm were 75%, 70%, and 60% (wt/wt), respectively, of the samples. Those particles < 37 microm were resuspended in another mixing chamber and then collected by a Moudi particle sampler. The largest mass fraction of resuspended road dust was in the range of 1-10 microm. Ultrafine particles (< 1 microm) composed 33.7, 17, and 7.4% of the particle samples (downtown, electrical park, and freeway tunnel, respectively). The road dust compositions were analyzed by inductively coupled plasma (ICP)-atomic emissions spectroscopy and ICP-mass spectrometry. The highest concentration fraction contained more aluminum (Al), iron (Fe), calcium (Ca), and potassium than other elements in the road dust particle samples. Additionally, the sulfur (S) content in the road dust from the electrical park and freeway tunnel areas was 2.1 and 3.4 times the downtown area sample, respectively. The sulfur originated from the vehicle and boiler oil combustion and industrial manufacturing processes. Furthermore, zinc (Zn) concentration in the tunnel dust was 2.6 times that of the downtown and electrical park samples, which can be attributed to vehicle tire wear and tear. Resuspended road dusts (< 10 microm) from the downtown and freeway tunnel areas were principally 2.5-10 microm Al, barium (Ba), Ca, copper (Cu), Fe, magnesium (Mg), sodium (Na), antimony (Sb), and Zn, whereas arsenic (As), chromium (Cr), and nickel (Ni) were predominant in the ultrafine particle samples (< 1 microm). Al, Ba, and Ca are the typical soil elements in coarse particles; and As, and Cr and Ni are the typical fingerprint of oil combustion and vehicle engine abrasion in ultrafine particles. There was a special characteristic of resuspension road dust at electrical park, that is, many elements, including As, Ba, Ca, cadmium, Cr, Cu, Fe, manganese (Mn), Ni, lead (Pb), S, vanadium (V), and Zn, were major in ultrafine particles. These elements should be attributed to the special manufacturing processes of electric products.     

A comparison of swine wastewater treatment using real-time and fixed-time two-stage sequencing batch reactors

This study compared the swine wastewater treatment of two identical lab-scale two-stage sequencing batch reactors (TSSBR) under similar conditions except that one was operated on a fixed-time mode and the other on a real-time mode. While both TSSBR systems performed very well, the real-time TSSBR performed far better then the fixed-time TSSBR, in every aspect of carbon, nitrogen, and phosphorous removal. The removals of COD, TOC, were at 97% and for BOD5 even at 99.7%. In terms of NH4-N and TKN removals, the real-time TSSBR achieved removal of over 98%. For phosphorus removals (Ortho-P and total P) the results from the real-time TSSBR was quite remarkable at 97.7%.     

Wash water in waterworks: contaminants and process options for reclamation

Reclamation of clean water from filter backwash water was studied through pilot-scale experiments.The pilot plant consisted of clarification,sand-filtration,and ultrafiltration modules in sequence,with a provision to bypass the sand filter.Clean water that conformed to World Health Organization (WHO) guidelines on Potable Quality was reclaimed.Turbidity,aluminum and iron were found to be critical contaminants in process selection and design.Clarification,followed by sand filtration,was found to be the minim...     

Enhancement of the polynomial functions response surface model for real-time analyzing ozone sensitivity

• The calculation process and algorithm of response surface model (RSM) were enhanced. • The prediction errors of RSM in the margin and transition areas were greatly reduced. • The enhanced RSM was able to analyze O₃-NO_x-VOC sensitivity in real-time. • The O₃ formations were mainly sensitive to VOC, for the two case study regions. Quantification of the nonlinearities between ambient ozone (O₃) and the emissions of nitrogen oxides (NO_x) and volatile organic compound (VOC) is a prerequisite for an effective O₃ control strategy. An Enhanced polynomial functions Response Surface Model (Epf-RSM) with the capability to analyze O₃-NO_x-VOC sensitivities in real time was developed by integrating the hill-climbing adaptive method into the optimized Extended Response Surface Model (ERSM) system. The Epf-RSM could single out the best suited polynomial function for each grid cell to quantify the responses of O₃ concentrations to precursor emission changes. Several comparisons between Epf-RSM and pf-ERSM (polynomial functions based ERSM) were performed using out-of-sample validation, together with comparisons of the spatial distribution and the Empirical Kinetic Modeling Approach diagrams. The comparison results showed that Epf-RSM effectively addressed the drawbacks of pf-ERSM with respect to over-fitting in the margin areas and high biases in the transition areas. The O₃ concentrations predicted by Epf-RSM agreed well with Community Multi-scale Air Quality simulation results. The case study results in the Pearl River Delta and the north-western area of the Shandong province indicated that the O₃ formations in the central areas of both the regions were more sensitive to anthropogenic VOC in January, April, and October, while more NO_x-sensitive in July.     

Photoreduction of Cr(VI) in wastewater by anodic nanoporous Nb2O5 formed at high anodizing voltage and electrolyte temperature

Environmental Science and Pollution Research - In this study, nanoporous anodic film was produced by anodization of niobium, Nb in a fluoride ethylene glycol electrolyte. The effect of anodization...