Study of the spatial variation of the biodegradation rate of the herbicide bentazone with soil depth using contrasting incubation methods

Vertical and horizontal spatial variability in the biodegradation of the herbicide bentazone was compared in sandy-loam soil from an agricultural field using sieved soil and intact soil cores. An initial experiment compared degradation at five depths between 0 and 80 cm using sieved soil. Degradation was shown to follow the first-order kinetics, and time to 50% degradation (DT(50)), declined progressively with soil depth from 56 d at 0-10 cm to 520 d at 70-80 cm. DT(50) was significantly correlated with organic matter, pH and dehydrogenase activity. In a subsequent experiment, degradation rate was compared after 127 d in sieved soil and intact cores from 0 to 10 and 50 to 60 cm depth from 10 locations across a 160x90 m portion of the field. Method of incubation significantly affected mean dissipation rate, although there were relatively small differences in the amount of pesticide remaining in intact cores and sieved soil, accounting for between 4.6% and 10.6% of that added. Spatial variability in degradation rate was higher in soil from 0 to 10 cm depth relative to that from 50 and 60 cm depth in both sieved soil and intact core assessments. Patterns of spatial variability measured using cores and sieved soil were similar at 50-60 cm, but not at 0-10 cm depth. This could reflect loss of environmental context following processing of sieved soil. In particular, moisture content, which was controlled in sieved soil, was found to be variable in cores, and was significantly correlated with degradation rate in intact topsoil cores from 0 to 10 cm depth.     

Speciation/fractionation of nickel in airborne particulate matter: improvements in the Zatka sequential leaching procedure

Modifications are reported to the sequential leaching analytical method for nickel speciation/fractionation specified by Zatka so that larger sample masses can be analyzed. Improvements have been made in the completeness of the sulfide/metallic separation during the peroxide-citrate leach step by use of a larger volume of leachant, a longer leach duration and an orbital shaker. Minimal extraction of metallic nickel in this prolonged sulfidic nickel extraction has been confirmed. An increase in the number of samples analyzed simultaneously using these modifications has resulted in substantial productivity improvements and concomitant lower costs. It is critical for practitioners of sequential leaching techniques to recognize potential limitations and to use professional judgment when interpreting results. For example, results obtained may not be biologically relevant in assessing health risks; the acts of sampling and storage may result in changes in fractionation with time; surface coatings/films may alter the ability of a leachant to react with the target compound; and leaching behaviours may be different for samples differing only in particle size distributions.     

The Clean Air Act Amendments and Motor Vehicle Inspection/Maintenance

Seventeen days of detailed measurements of NO, NO₂, O₃, HNO₃ and the frequency of NO₂ photolysis—j(NO₂)—were carried out in Claremont, CA, in September 1980. Under conditions when the rate of change of NO concentration is small, there must be a balance between formation and loss processes. In the classical photostationary state this balance is between NO₂ photolysis: NO₂ + hv → NO + O and reaction with ozone: NO + O₃ → NO₂ + O₂. The results show that the latter reaction with ozone is inadequate to balance the formation step; a significant contribution is required from another NO oxidation process, possibly peroxy radical oxidation. If so, the inferred concentration of peroxy radicals shows a diurnal variation, peaking around solar noon.     

Emissions from lit-use Motor Vehicles in Los Angeles: A Pilot Study of Remote Sensing and the Inspection and Maintenance Program

As part of a major field study to understand the causes of persistent, elevated carbon monoxide pollution episodes in Los Angeles, we performed a project to understand the emissions of vehicles in use. In this experiment, we assessed the accuracy of a remote sensing instrument designed to measure CO concentrations from vehicles as they were driven on the road. The remote sensor was shown to be accurate within ten percent of the directly measured tailpipe value. We performed a roadside inspection on 60 vehicles and demonstrated that the remote sensor could be used as an effective surveillance tool to identify high CO-emitting vehicles. We also compared the roadside data set to the biennial Smog Check (I/M) tests for the same vehicles, and observed that carbon monoxide and exhaust hydrocarbons from high emitters were much higher than when the vehicles received their routine inspection. Furthermore, for the high-emitting vehicles in this data set, the length of time since the biennial Smog Check had little influence on the cars’ emissions in the roadside inspection.     

Canister-Based Method for Monitoring Toxic VOCs in Ambient Air

The availability of reliable, accurate and precise monitoring methods for toxic volatile organic compounds (VOCs) is a primary need for state and local agencies addressing daily monitoring requirements related to odor complaints, fugitive emissions, and trend monitoring. The canister-based monitoring method for VOCs is a viable and widely used approach that is based on research and evaluation performed over the past several years. This activity has involved the testing of sample stability of VOCs in canisters and the design of time-integrative samplers. The development of procedures for analysis of samples in canisters, including the procedure for VOC preconcentration from whole air, the treatment of water vapor in the sample, and the selection of an appropriate analytical finish has been accomplished. The canister-based method was initially summarized in the EPA Compendium of Methods for the Determination of Toxic Organic Compounds in Ambient Air as Method TO-14. Modifications and refinements are being added to Method TO-14 in order to obtain a Statement of Work for the Superfund Contract Laboratory Program for Air. This paper discusses the developments leading to the current status of the canisterbased method and provides a critique of the method using results obtained in EPA monitoring networks.     

Particle Mass Emission Rates from Current-Technology,Light-Duty Gasoline Vehicles

ABSTRACT

Now that the U.S. Environmental Protection Agency has promulgated new National Ambient Air Quality Standards for PM_2.5, work will begin on generating the data required to determine the sources of ambient PM_2.5 and the magnitude of their contributions to air pollution. This paper summarizes the results of an Environmental Research Consortium program, carried out under the auspices of the U.S. Council for Automotive Research. The program focused on particulate matter (PM) emissions from representative, current-technology, light-duty gasoline vehicles produced by DaimlerChrysler Corp., Ford Motor Co., and General Motors Corp. The vehicles, for the most part taken from the manufacturer's certification and durability fleets, were dynamometer-tested using the three-phase Federal Test Procedure in the companies' laboratories. The test fleet was made up of a mixture of both low-mileage (2K-35K miles) and high-mileage (60K-150K miles) cars, vans, sport utility vehicles, and light trucks. For each vehicle tested, PM emissions were accumulated over 4 cold-start tests, which were run on successive days. PM emission rates from the entire fleet (22 vehicles total) averaged less than 2 mg/mile. All 18 vehicles tested using California Phase 2 reformulated gasoline had PM emission rates less than 2 mg/ mile at both low and high mileages.     

Preparation of Calcium Silicate Absorbent from Iron Blast Furnace Slag

ABSTRACT

Calcium silicate hydrate (CSH) solids were prepared from hydrated lime and iron blast furnace slag in an aqueous agitated slurry at 92 °C. While it was hoped a minimal lime/slag ratio could be used to create near-amorphous CSH, the surface area of the product improved by increasing the lime/slag weight ratio to 2. The addition of gypsum to the lime/slag system dramatically improved the formation of surface area, creating solids with 139 m²/g after 30 hr of reaction when only a minimal amount of lime was present. The SO₂ reactivity of solids prepared with gypsum greatly exceeded that of hydrated lime, achieving greater than 70-80% conversion of the alkalinity after 1 hr of reaction with SO₂. The use of CaCl₂ as an additive to the lime/slag system, in lieu of gypsum, also produced high-surface-area solids, 115 m²/g after 21 hr of reaction. However, the SO₂ reactivity of these sorbents was relatively low given the high surface area. This emphasized that the correlation between surface area and SO₂ reactivity was highly dependent on the solid phase, which was subsequently dependent on slurry composition.     

Workplace and Environmental Air Contaminant Concentrations Measured by Open Path Fourier Transform Infrared Spectroscopy: A Statistical Process Control Technique to Detect Changes from Normal Operating Conditions

Open path Fourier transform infrared (OP-FTIR) spectroscopy is a new air monitoring technique that can be used to measure concentrations of air contaminants in real or near-real time. OP-FTIR spectroscopy has been used to monitor workplace gas and vapor exposures, emissions from hazardous waste sites, and to track emissions along fence lines. This paper discusses a statistical process control technique that can be used with air monitoring data collected with an OP-FTIR spectrometer to detect departures from normal operating conditions in the workplace or along a fence line. Time series data, produced by plotting consecutive air sample concentrations in time, were analyzed. Autocorrelation in the time series data was removed by fitting dynamic models. Control charts were used with the residuals of the model fit data to determine if departures from defined normal operating conditions could be rapidly detected. Shewhart and exponentially weighted moving average (EWMA) control charts were evaluated for use with data collected under different room air flow and mixing conditions.

Under rapidly changing conditions the Shewhart control chart was able to detect a leak in a simulated process area. The EWMA control chart was found to be more sensitive to drifts and slowly changing concentrations in air monitoring data. The time series and statistical process control techniques were also applied to data obtained during a field study at a chemical plant. A production area of an acrylonitrile, 1,3-butadiene, and styrene (ABS) polymer process was monitored in near-real time. Decision logics based on the time series and statistical process control technique introduced suggest several applications in workplace and environmental monitoring. These applications might include signaling of an alarm or warning, increasing levels of worker respiratory protection, or evacuation of a community, when gas and vapor concentrations are determined to be out-of-control.     

Optimization of a horizontal-flow biofilm reactor for the removal of methane at low temperatures

Three pilot-scale, horizontal-flow biofilm reactors (HFBRs 1–3) were used to treat methane (CH₄)-contaminated air to assess the potential of this technology to manage emissions from agricultural activities, waste and wastewater treatment facilities, and landfills. The study was conducted over two phases (Phase 1, lasting 90 days and Phase 2, lasting 45 days). The reactors were operated at 10 °C (typical of ambient air and wastewater temperatures in northern Europe), and were simultaneously dosed with CH₄-contaminated air and a synthetic wastewater (SWW). The influent loading rates to the reactors were 8.6 g CH₄/m³/hr (4.3 g CH₄/m² TPSA/hr; where TPSA is top plan surface area). Despite the low operating temperatures, an overall average removal of 4.63 g CH₄/m³/day was observed during Phase 2. The maximum removal efficiency (RE) for the trial was 88%. Potential (maximum) rates of methane oxidation were measured and indicated that biofilm samples taken from various regions in the HFBRs had mostly equal CH₄ removal potential. In situ activity rates were dependent on which part of the reactor samples were obtained. The results indicate the potential of the HFBR, a simple and robust technology, to biologically treat CH₄ emissions.

Implications: The results of this study indicate that the HFBR technology could be effectively applied to the reduction of greenhouse gas emissions from wastewater treatment plants and agricultural facilities at lower temperatures common to northern Europe. This could reduce the carbon footprint of waste treatment and agricultural livestock facilities. Activity tests indicate that methanotrophic communities can be supported at these temperatures. Furthermore, these data can lead to improved reactor design and optimization by allowing conditions to be engineered to allow for improved removal rates, particularly at lower temperatures. The technology is simple to construct and operate, and with some optimization of the liquid phase to improve mass transfer, the HFBR represents a viable, cost-effective solution for these emissions.