Short-term Distributions of Reduced Sulfur Compounds in the Ambient Air Surrounding a Large Landfill Facility

In order to explore the environmental behavior of reduced sulfur compounds (RSC) as malodorous components emitted from diverse source processes, the distribution characteristics of four sulfur (S) compounds - hydrogen sulfide (H₂S), methyl mercaptan (CH₃SH), dimethyl sulfide (DMS: (CH₃)₂S), and dimethyl disulfide (DMDS: (CH₃)₂S₂) – were investigated in a municipal landfill area. In the course of this study, their ambient concentration levels were measured during two time periods from 13 individual spots selected as a function of distance from the center of the landfill site. The results generally indicated the absolute dominance of H₂S over the other S compounds investigated (up to 5 km radius) such that their mean values were found as 1415 (H₂S), 148 (DMS), 20.6 (CH₃SH), and 14.4 ppt (DMDS). When our data were compared in terms of either varying distance from the source or relationship with meteorological conditions, the H₂S data sets were most evident to reflect the potential effects of strong source processes in the landfill environment, relative to other S gases (or to volatile organic compounds measured concurrently). The results of this study further indicated the relatively good correspondence between the measured H₂S concentration level and humans' intuitive sensory of odor and nuisance.     

Fine particle removal performance of a two-stage wet electrostatic precipitator using a nonmetallic pre-charger

A novel two-stage wet electrostatic precipitator (ESP) has been developed using a carbon brush pre-charger and collection plates with a thin water film. The electrical and particle collection performance was evaluated for submicrometer particles smaller than 0.01- 0.5 micrometer in diameter by varying the voltages applied to the pre-charger and collection plates as well as the polarity of the voltage. The collection efficiency was compared with that calculated by the theoretical models. The long-term performances of the ESP with and without water films were also compared in tests using Japanese Industrial Standards dust. The experimental results show that the carbon brush pre-charger of the two-stage wet ESP had approximately 10% particle capture, while producing ozone concentrations of less than 30 ppb. The produced amounts of ozone are significantly lower than the current limits set by international agencies. The ESP also achieved a high collection rate performance, averaging 90% for ultrafine particles, as based on the particle number concentration at an average velocity of 1 m/sec corresponding to a residence time of 0.17 sec. Higher particle collection efficiency for the ESP can be achieved by increasing the voltages applied to the pre-charger and the collection plates. The decreased collection efficiency that occurred during dust loading without water films was completely avoided by forming a thin water film on the collection plates at a water flow rate of 6.5 L/min/m(2).     

Behavior of PAHs from sewage sludge incinerators in Korea

Although production of sewage sludge increases every year, its proper treatment has only been recently raised as a new issue, as current landfill and ocean dumping arrangements are expected to become increasingly difficult to manage in the future. The Korean Ministry of Environment plans to diversify its processing facilities and expand its processing systems by 2011, with the purpose of processing all sludge produced in Korea. According to this plan, incineration (including incineration of municipal wastes) will process 30% of the entire sewage sludge throughout the country in 2011. This study reviews the characteristics of PAH, which is one of the organic substances found in sewage sludge during the incinerating process. The total amount of PAH produced from sewage sludge incineration was found to be 6.103 mg/kg on average, and investigation performed on 16 PAHs of inlets and outlets of the air control devices at five full-scale incineration facilities showed that concentrations of the PAHs on the inlet and on the outlet ranged from 3.926 to 925.748 microg/m(3) and from 1.153 to 189.449 microg/m(3), respectively. In the case of the incineration facility fed with municipal waste (95%) and sewage sludge (5%), the total of the PAH emissions concentration was higher than that found at the incineration facilities used exclusively to treat sewage. The combustion of waste vinyl and plastics contained in municipal waste fed into the facility might contribute to the high levels of PAHs in the stack gas. However more investigation is needed on the production mechanism of PAHs at different operating conditions of the incineration facilities, such as the types of waste, and other relevant factors.     

A simultaneous equations model of crash frequency by collision type for rural intersections

Safety at roadway intersections is of significant interest to transportation professionals due to the large number of intersections in transportation networks, the complexity of traffic movements at these locations that leads to large numbers of conflicts, and the wide variety of geometric and operational features that define them. A variety of collision types including head-on, sideswipe, rear-end, and angle crashes occur at intersections. While intersection crash totals may not reveal a site deficiency, over exposure of a specific crash type may reveal otherwise undetected deficiencies. Thus, there is a need to be able to model the expected frequency of crashes by collision type at intersections to enable the detection of problems and the implementation of effective design strategies and countermeasures. Statistically, it is important to consider modeling collision type frequencies simultaneously to account for the possibility of common unobserved factors affecting crash frequencies across crash types. In this paper, a simultaneous equations model of crash frequencies by collision type is developed and presented using crash data for rural intersections in Georgia. The model estimation results support the notion of the presence of significant common unobserved factors across crash types, although the impact of these factors on parameter estimates is found to be rather modest.     

Application of a weights-of-evidence method and GIS to regional groundwater productivity potential mapping

The aim of this study is to analyze the relationship among groundwater productivity data including specific capacity (SPC) and transmissivity (T) as well as its related hydrogeological factors in a bedrock aquifer, and subsequently, to produce the regional groundwater productivity potential (GPP) map for the area around Pohang City, Korea using a geographic information system (GIS) and a weights-of-evidence (WOE) model. All of the related factors, including topography, lineament, geology, forest, and soil data were collected and input into a spatial database. In addition, SPC and T data were collected from 83 and 81 well locations, respectively. Four dependent variables including SPC values of ≥6.25 m3/d/m (Case 1) and T values of ≥3.79 m2/d (Case 3) corresponding to a yield (Y) of ≥500 m3/d, and SPC values of ≥3.75 m3/d/m (Case 2) and T values of ≥2.61 m2/d (Case 4) corresponding to a Y of ≥300 m3/d were also input into a spatial database. The SPC and T data were randomly selected in an approximately 70:30 ratio to train and validate the WOE model. Tests of conditional independence were performed for the used factors. To assess the regional GPP for each dependent variable, W+ and W- of each factor's rating were overlaid spatially. The results of the analysis were validated using area under curve (AUC) analysis with the existing SPC and T data that were not used for the training of the model. The AUC of Cases 1, 2, 3 and 4 showed 0.7120, 0.6893, 0.6920, and 0.7098, respectively. In the case of the dependent variables, Case 1 had an accuracy of 71.20% (AUC: 0.7120), which is the best result produced in this analysis. Such information and the maps generated from it could be used for groundwater management, a practice related to groundwater resource exploration.     

Effects of various reaction parameters on solvolytical depolymerization of lignin in sub- and supercritical ethanol

Organosolv lignin was treated with ethanol at sub/supercritical temperatures (200, 275, and 350 °C) for conversion to low molecular phenols under different reaction times (20, 40, and 60 min), solvent-to-lignin ratios (50, 100, and 150 mL g⁻¹), and initial hydrogen gas pressures (2 and 3 MPa). Essential lignin-degraded products, oil (liquid), char (solid), and gas were obtained, and their yields were directly influenced by reaction conditions. In particular, concurrent reactions involving depolymerization and recondensation as well as further (secondary) decomposition were significantly accelerated with increasing temperature, leading to both lignin-derived phenols in the oil fraction and undesirable products (char and gas).     

Aquatic toxicity of cartap and cypermethrin to different life stages of Daphnia magna and Oryzias latipes

Cartap and cypermethrin, which are among the most widely used pesticides in many countries, are considered safe because of their low mammalian toxicity and their low persistence in the environment. However, recent findings of endocrine-disrupting effects and developmental neurotoxicity have raised concerns about the potential ecological impacts of these pesticides. We evaluated the aquatic toxicity of cartap [S,S′-(2-dimethylaminotrimethylene) bis(thiocarbamate), unspecified hydrochloride] and cypermethrin [(RS)-alpha-cyano-3-phenoxybenzyl-(1RS,3RS,1RS,3SR)-3-(2,2-dichlorovinyl)-2,2-dimethylcyclopropane carboxylate], both individually and combined, on different life stages of the freshwater cladoceran Daphnia magna and a freshwater teleost, Japanese medaka (Oryzias latipes). The 96-hr Daphnia median effective concentrations (EC50s) for cartap and cypermethrin were 91.0 μ g/L and 0.00061 μ g/L, respectively. Rapid recovery of Daphnia was observed after short-term pulsed exposure to cartap and cypermethrin; there were no adverse effects on reproduction or survival 20 d after a 24 hr exposure to cartap up to 1240 μ g/L and cypermethrin up to 1.9 μ g/L. Chronic continuous exposure (for 21 d) of 7-d-old Daphnia to cypermethrin significantly reduced the intrinsic population growth rate in a concentration-dependent manner. However, because the intrinsic population growth rates were all above zero, populations did not decrease even at the highest experimental concentration of 200 ng/L. Exposure of Daphnia neonates (< 24 hr old) to cypermethrin for 21 d caused significant, sub-lethal reproduction-related problems, such as increased time to first brood, reduced brood size, and reduced total brood number, at 0.0002, 0.002, and 0.2 ng/L cypermethrin, but the intrinsic population growth rate was not significantly affected. Oryzias latipes was relatively more resistant to both pesticides. In particular, embryos appeared to be more resistant than juveniles or adults, which may be partly due to the protective role of the chorion. The incidence of larval fish deformity was significantly higher after a 96 hr exposure to as low as 250 μ g/L of cartap or 40 μ g/L of cypermethrin. The mixture of both compounds showed no synergistic toxicity. The extremely high acute-to-chronic ratio suggests that the standard acute lethal toxicity assessment might not reflect the true environmental hazards of these frequently used pesticides. Ecological hazard assessments of long-term low dose or pulsed exposures to cartap and cypermethrin may reveal more realistic consequences of these compounds in surface water.     

An international comparative study of end-of-life vehicle (ELV) recycling systems

End-of-life vehicles (ELV) have become a global concern as automobiles have become popular worldwide. An international workshop was held to gather data and to discuss 3R policies and ELV recycling systems, their background and present situation, outcomes of related policies and programs, the framework of recycling and waste management, and case studies on related topics in several countries and regions, as well as the essential points of the comparison. Legislative ELV recycling systems are established in the EU, Japan, Korea, and China, while in the US, ELV recycling is managed under existing laws on environmental protection. Since automobile shredding residue (ASR) has a high calorific value and ash content, and includes heavy metals as well as a mass of unclassified fine particles, recycling ASR is considered highly difficult. Countries with a legislative ELV system commonly set a target for recovery rates, with many aiming for more than 95 % recovery. In order to reach this target, higher efficiency in ASR recovery is needed, in addition to material recycling of collectable components and metals. Environmentally friendly design was considered necessary at the planning and manufacturing stages, and the development of recycling systems and techniques in line with these changes are required for sound ELV management.     

Heavy metal immobilization in soil near abandoned mines using eggshell waste and rapeseed residue

Heavy metal contamination of agricultural soils has received great concern due to potential risk to human health. Cadmium and Pb are largely released from abandoned or closed mines in Korea, resulting in soil contamination. The objective of this study was to evaluate the effects of eggshell waste in combination with the conventional nitrogen, phosphorous, and potassium fertilizer (also known as NPK fertilizer) or the rapeseed residue on immobilization of Cd and Pb in the rice paddy soil. Cadmium and Pb extractabilities were tested using two methods of (1) the toxicity characteristics leaching procedure (TCLP) and (2) the 0.1 M HCl extraction. With 5 % eggshell addition, the values of soil pH were increased from 6.33 and 6.51 to 8.15 and 8.04 in combination with NPK fertilizer and rapeseed residue, respectively, compared to no eggshell addition. The increase in soil pH may contribute to heavy metal immobilization by altering heavy metals into more stable in soils. Concentrations of TCLP-extracted Cd and Pb were reduced by up to 67.9 and 93.2 % by addition of 5 % eggshell compared to control. For 0.1 M HCl extraction method, the concentration of 0.1 M HCl-Cd in soils treated with NPK fertilizer and rapeseed residue was significantly reduced by up to 34.01 and 46.1 %, respectively, with 5 % eggshell addition compared to control. A decrease in acid phosphatase activity and an increase in alkaline phosphatase activity at high soil pH were also observed. Combined application of eggshell waste and rapeseed residue can be cost-effective and beneficial way to remediate the soil contaminated with heavy metals.     

Fine Particle Removal Performance of a Two-Stage Wet Electrostatic Precipitator Using a Nonmetallic Pre-Charger

ABSTRACT

A novel two-stage wet electrostatic precipitator (ESP) has been developed using a carbon brush pre-charger and collection plates with a thin water film. The electrical and particle collection performance was evaluated for submicrometer particles smaller than 0.01～0.5 μm in diameter by varying the voltages applied to the pre-charger and collection plates as well as the polarity of the voltage. The collection efficiency was compared with that calculated by the theoretical models. The long-term performances of the ESP with and without water films were also compared in tests using Japanese Industrial Standards dust. The experimental results show that the carbon brush pre-charger of the two-stage wet ESP had approximately 10% particle capture, while producing ozone concentrations of less than 30 ppb. The produced amounts of ozone are significantly lower than the current limits set by international agencies. The ESP also achieved a high collection rate performance, averaging 90% for ultrafine particles, as based on the particle number concentration at an average velocity of 1 m/sec corresponding to a residence time of 0.17 sec. Higher particle collection efficiency for the ESP can be achieved by increasing the voltages applied to the pre-charger and the collection plates. The decreased collection efficiency that occurred during dust loading without water films was completely avoided by forming a thin water film on the collection plates at a water flow rate of 6.5 L/min/m2 Zukeran, A., Ikeda, Y., Ehara, Y., Matsuyama, M., Ito, T., Takahashi, T., Kawakami, H. and Takamatsu, T. 1999. Two-Stage-Type Electrostatic Precipitator Re-entrainment Phenomena under Diesel Flue Gases. IEEE. Trans. Ind. Appl, 35: 346–351. [Crossref], [Web of Science ®] , [Google Scholar].

IMPLICATIONS Current two-stage electrostatic precipitators (ESPs) have several technical problems such as a drop in collection efficiencies by small-particle re-entrainment during rapping and corrosion of metallic electrodes of the ESPs by corrosive gases. This paper evaluates a novel two-stage ESP that uses a nonmetallic pre-charger and water film collection plates to avoid the above mentioned problems of other ESPs. This ESP can be used not only for industrial applications but also for residential purposes because it has a high removal performance for fine particles with low ozone generation and maintains its efficiency due to the continuous cleaning of the collection plates with water film.