Discriminating the regional and urban contributions in the North-Western Mediterranean: PM levels and composition

Simultaneous measurements of the PM concentration levels and chemical composition of atmospheric aerosols at a regional background (RB) and an urban background (UB) site, located in the same geographic region, allowed for the determination of their urban and regional contributions. In the specific case of the North-Western region of the Mediterranean the RB amount has been quantified in 18, 13 and 12 μg m^?3 for PM₁₀, PM_2.5 and PM₁, respectively, whereas the UB contribution reached 22, 13 and 8 μg m^?3, respectively. The UB contributions in the Western Mediterranean are much higher than those observed in other European regions; especially concerning the coarse fraction. The high loads of road dust in the urban areas across the Mediterranean may account for these large differences.The urban contributions are extremely enriched in Ca, Fe, Sb, Sn, Cu, Zn, being the main tracers of the road dust, with concentrations up to 6–8 times higher than those at the RB. Elemental carbon and nitrate are mainly derived from direct vehicular emissions. Some industrial tracers (Mn, Pb, Bi) are also enriched in the urban area. The evaluation of the Cu/Sb, Cu/Zn, Cu/Cd and Cu/Pb ratios and the high enrichment of these trace elements versus the Upper Crustal Composition average values corroborates the importance of the road-traffic emissions in the study area, also influencing the RB.The supplementary results from a suburban site in the Balearic Islands and the evaluation of the V/Ni ratios evidence the strong signature of fuel-oil combustion processes, which is a general characteristic of the Mediterranean aerosols.     

A simplified approach to the indirect evaluation of the chemical composition of atmospheric aerosols from PM mass concentrations

The present work shows a straightforward procedure to indirectly estimate the chemical composition at a given site only from the determination of the PM concentrations, and the classification of the days according to the main meteorological scenarios. A previous study based on the mean chemical composition associated to the main meteorological scenarios is required.This experiment has been carried out with data from two monitoring sites in the North-Western Mediterranean, one regional and one suburban background. At both sites, one-year datasets on chemical PM₁₀ composition were obtained. Based on these datasets, the mean PM₁₀ compositions according to the most relevant meteorological situations were calculated for both locations. After that, the reconstruction of the chemical composition for all the days with available PM₁₀ concentrations was completed. Subsequently, the estimated PM₁₀ composition was compared with that determined experimentally. The comparison between the rebuilt and the experimental results was very satisfactory in the case of the regional background site, and relatively replaced in the other case. Furthermore, the validation of the method at the regional background site has been conducted from the reconstruction of a 4-year data base, and subsequent comparison with the experimental chemical composition.Our results show that it is possible to attain a good approach to the chemical composition at regional background sites, where local emission sources are negligible. Conversely, when the local sources rise in importance, i.e., at a suburban background site, the approach is suitable only for those components with a more regional origin and/or those from long range transport of air masses.     

Multimedia fate modeling and comparative impact on freshwater ecosystems of pharmaceuticals from biosolids-amended soils

This study modeled the impact on freshwater ecosystems of pharmaceuticals detected in biosolids following application on agricultural soils. The detected sulfonamides and hydrochlorothiazide displayed comparatively moderate retention in solid matrices and, therefore, higher transfer fractions from biosolids to the freshwater compartment. However, the residence times of these pharmaceuticals in freshwater were estimated to be short due to abiotic degradation processes. The non-steroidal anti-inflammatory mefenamic acid had the highest environmental impact on aquatic ecosystems and warrants further investigation. The estimation of the solid-water partitioning coefficient was generally the most influential parameter of the probabilistic comparative impact assessment. These results and the modeling approach used in this study serve to prioritize pharmaceuticals in the research effort to assess the risks and the environmental impacts on aquatic biota of these emerging pollutants.     

Determination of direct and fugitive PM emissions in a Mediterranean harbour by means of classic and novel tracer methods

Remodelling works are frequent in harbour areas, given that they must adapt to rapidly changing market requirements. Depending on their nature (construction, demolition, etc.), these works may be carried out during long periods of time and thus exert a significant impact on the air quality at the harbours and their surroundings. The air quality at the Valencia harbour was studied during an enlargement project. Four sampling stations aimed to cover the major dust-emitting activities in the harbour. In addition, a sampling campaign was carried out to collect dust materials at their emission sources (e.g., loading and unloading of clinker and petroleum coke, as well as the enlargement works). Differences obtained between PM levels at the monitoring sites were correlated with the distance between sampling stations and enlargement works and/or harbour operations, as well as with the preferential wind direction. In all cases, the days with the highest PM_10 levels were linked to wind directions coinciding with the location of the enlargement works or the clinker and petroleum coke stocks. Classic source apportionment methodologies (PCA and CMB) were applied to the data, but their interpretation was complex due to the similar chemical signatures of PM originating from direct and fugitive emissions from stocked materials (e.g., clinker), and the enlargement works. To overcome this difficulty, a novel non-statistical approach was used to obtain quantitative estimations of the contributions from sources (petroleum coke and clinker), based on the correlation between specific PM components (e.g., carbonaceous species) and source tracers (e.g., V). Finally, a qualitative test using phenolphthalein was devised to identify the presence of clinker on the filters, which provided positive results. This novel tracer approach is thus recommended for harbour authorities.     

Persistence and effect of processing on reduction of chlorantraniliprole residues on brinjal and okra fruits

Dissipation and decontamination of chlorantraniliprole (Coragen 18.5 SC) in brinjal and okra fruits were studied following field application at single and double doses of 30 and 60 g ai ha^?1, and the residues of the insecticide was estimated using LC-MS/MS. Initial residues of chlorantraniliprole at single and double doses on the fruits of brinjal were 0.72 and 1.48 mg kg^?1, while on okra fruits, the residues were 0.48 and 0.91 mg kg^?1, respectively. The residues reached below detectable level of 0.01 mg kg^?1 on the 10th day. Half-life of chlorantraniliprole at 30 and 60 g ai ha^?1 on brinjal was 1.58 and 1.80 days with the calculated waiting period of 0.69 and 2.38 days, whereas on okra, the values were 1.60 and 1.70 and 0 and 1.20 days, respectively. The extent of removal of chlorantraniliprole using simple decontaminating techniques at 2 h and 3 days after spraying was 40.99–91.37 % and 29.85–89.12 %, respectively, from brinjal fruits and 47.78–86.10 % and 41.77–86.48 %, respectively, from okra fruits.     

Workplace aerosol mass concentration measurement using optical particle counters

Direct-reading aerosol measurement usually uses the optical properties of airborne particles to detect and measure particle concentration. In the case of occupational hygiene, mass concentration measurement is often required. Two aerosol monitoring methods are based on the principle of light scattering: optical particle counting (OPC) and photometry. The former analyses the light scattered by a single particle, the latter by a cloud of particles. Both methods need calibration to transform the quantity of scattered light detected into particle concentration. Photometers are simpler to use and can be directly calibrated to measure mass concentration. However, their response varies not only with aerosol concentration but also with particle size distribution, which frequently contributes to biased measurement. Optical particle counters directly measure the particle number concentration and particle size that allows assessment of the particle mass provided the particles are spherical and of known density. An integrating algorithm is used to calculate the mass concentration of any conventional health-related aerosol fraction. The concentrations calculated thus have been compared with simultaneous measurements by conventional gravimetric sampling to check the possibility of field OPC calibration with real workplace aerosols with a view to further monitoring particle mass concentration. Aerosol concentrations were measured in the food industry using the OPC GRIMM? 1.108 and the CIP 10-Inhalable and CIP 10-Respirable (ARELCO?) aerosol samplers while meat sausages were being brushed and coated with calcium carbonate. Previously, the original OPC inlet had been adapted to sample inhalable aerosol. A mixed aerosol of calcium carbonate and fungi spores was present in the workplace. The OPC particle-size distribution and an estimated average particle density of both aerosol components were used to calculate the mass concentration. The inhalable and respirable aerosol fractions calculated from the OPC data are closely correlated with the results of the particle size-selective sampling using the CIP 10. Furthermore, the OPC data allow calculation of the thoracic fraction of workplace aerosol (not measured by sampling), which is interesting in the presence of allergenic particles like fungi spores. The results also show that the modified COP inlet adequately samples inhalable aerosol in the range of workplace particle-size distribution.     

Rate of occurrence of failures based on a nonhomogeneous Poisson process: an ozone analyzer case study

Atmospheric pollutant monitoring constitutes a primordial activity in public policies concerning air quality. In São Paulo State, Brazil, the São Paulo State Environment Company (CETESB) maintains an automatic network which continuously monitors CO, SO₂, NO _x , O₃, and particulate matter concentrations in the air. The monitoring process accuracy is a fundamental condition for the actions to be taken by CETESB. As one of the support systems, a preventive maintenance program for the different analyzers used is part of the data quality strategy. Knowledge of the behavior of analyzer failure times could help optimize the program. To achieve this goal, the failure times of an ozone analyzer—considered a repairable system—were modeled by means of the nonhomogeneous Poisson process. The rate of occurrence of failures (ROCOF) was estimated for the intervals 0–70,800 h and 0–88,320 h, in which six and seven failures were observed, respectively. The results showed that the ROCOF estimate is influenced by the choice of the observation period, t ₀?=?70,800 h and t ₇?=?88,320 h in the cases analyzed. Identification of preventive maintenance actions, mainly when parts replacement occurs in the last interval of observation, is highlighted, justifying the alteration in the behavior of the inter-arrival times. The performance of a follow-up on each analyzer is recommended in order to record the impact of the performed preventive maintenance program on the enhancement of its useful life.     

Coupled solar photo-Fenton and biological treatment for the degradation of diuron and linuron herbicides at pilot scale

A coupled solar photo-Fenton (chemical) and biological treatment has been used to remove biorecalcitrant diuron (42 mg l(-1)) and linuron (75 mg l(-1)) herbicides from water at pilot plant scale. The chemical process has been carried out in a 82 l solar pilot plant made up by four compound parabolic collector units, and it was followed by a biological treatment performed in a 40 l sequencing batch reactor. Two Fe(II) doses (2 and 5 mg l(-1)) and sequential additions of H2O2 (20 mg l(-1)) have been used to chemically degrade the initially polluted effluent. Next, biodegradability at different oxidation states has been assessed by means of BOD/COD ratio. A reagent dose of Fe=5 mg l(-1) and H2O2=100 mg l(-1) has been required to obtain a biodegradable effluent after 100 min of irradiation time. Finally, the organic content of the photo-treated solution has been completely assimilated by a biomass consortium in the sequencing batch reactor using a total suspended solids concentration of 0.2 g l(-1) and a hydraulic retention time of 24h. Comparison between the data obtained at pilot plant scale (specially the one corresponding to the chemical step) and previously published data from a similar system performing at laboratory scale, has been carried out.