温度对热水解预处理高含固污泥特性的影响

以含固率为10%的污泥为对象,研究不同温度和时间条件下热水解过程中有机物转化规律对污泥特性的影响。结果表明:随着热水解时间的延长和温度的升高,污泥中挥发性悬浮固体(VSS)的水解率逐渐升高。在热水解时间为20 min时,温度由150℃升高到180℃,VSS水解率由22.9%增至38.4%,污泥中VSS由46.28 g/L降低到40.63 g/L。水解液组分分析表明,溶解性化学需氧量(SCOD)主要组成为蛋白质(50%)、碳水化合物(15%~20%)、可挥发性脂肪酸(15%~20%)。水解液中氮主要以有机氮的形式存在。在热水解条件达到165℃、50 min时,氨氮浓度为1.16 g/L,之后,随着温度的升高和时间的延长,氨氮浓度基本不变。     

不干胶废弃物热解与燃烧动力学特性

采用热重分析方法对不干胶废弃物(PSAs)进行了热解和燃烧失重分析,并采用Doyle法拟合计算了PSAs热解和燃烧动力学参数。结果表明:当温度低于200℃或高于600℃,PSAs的热解和燃烧失重过程具有性;300~600℃时,PSAs热解过程具有3个失重峰,而其燃烧过程具有2个失重峰。动力学分析结果表明:PSAs的热解是由多阶段复杂的热裂解反应组成,其热解过程可用4个一级反应来描述,随着升温速率的提高热解阶段第1峰区表观活化能降低;而第2、3峰区以及半焦深度裂解阶段的第4峰区活化能逐渐升高;PSAs燃烧过程可用3个一级反应来描述,随着升温速率的提高,PSAs燃烧过程的表观活化能均逐渐降低,并且燃烧表观活化能均低于热解表观活化能。     

阳宗海沉积物中磷的稳定性

絮凝剂(FeCl3)治理阳宗海砷污染的过程中,水体中的磷被大量沉积进入底泥,弄清其是否会在环境条件变化后发生反溶形成二次污染对湖泊富营养化防治具有重要意义。通过模拟实验模拟泥-水界面pH变化、物理扰动和微生物活动的变化,旨在分析这些环境因子变化对沉积物中磷溶出的影响。结果表明,阳宗海水体在目前这种磷浓度下,底泥的磷会随时间的增加而溶出再次造成水体磷污染,当暴露在清洁水条件下时磷的释放率会增加;这种由于絮凝剂吸附沉淀到湖底的磷,在上覆水pH增加0.5时底泥磷解吸附释放速率增加;每年秋季湖泊上下层水的交换活动会造成水体磷浓度的季节性升高,形成不可忽视的磷内源。而夏季水温分层导致湖泊底部厌氧,使厌氧微生物活性增强,这将进一步促进底泥中磷的释放。     

粉末活性污泥处理含铀废水的特性

以生活污水处理厂剩余活性污泥为原料,制备粉末活性污泥(PAS)作为生物吸附剂,考察pH值,PAS投加量,U(Ⅵ)初始浓度和吸附时间对PAS吸附U(Ⅵ)的影响,探讨了PAS吸附U(Ⅵ)的作用机理。实验结果表明,在U(Ⅵ)初始浓度为10 mg/L时,其最佳吸附pH值为3,去除率97.77%,吸附平衡时间120 min;吸附过程较好地拟合了准二级动力学模型(R2≈1)和Freundlich等温模型(R2≈1);X射线能谱和离子交换实验分析表明,离子交换为其主要吸附方式,参与交换的主要离子为Ca2+;红外光谱分析表明,PAS吸附U(Ⅵ)后自身结构未发生改变。以0.1 mol/L的HCl溶液作为解吸液,初次解吸率达92.83%,循环利用3次仍具有较好的吸附效果。     

巢湖低温高效聚磷菌的筛选及其特性

采用低温富集培养及混合平板分离技术,从巢湖底泥中分离筛选得到2株在低温下仍具有较高效能的菌株D3、D6,经过厌氧/好氧交替培养,2种菌株在低温下(8℃)的除磷率均达到80%以上。在低温下,研究了pH、微量元素对2株菌株生长及除磷率的影响,实验结果表明,2株菌都具有广泛的温度适应性,适宜其生长和除磷的pH为中性偏碱,微量元素的缺乏对2株菌株的生长和除磷效果有不同程度的不良影响。染色观察显示,厌氧培养时菌体内聚羟基丁酸(PHB)颗粒明显增多,转为好氧培养后异染颗粒增多,为典型的聚磷菌特征。经鉴定,2株菌均属假单胞菌属。     

聚硅酸钛制备及其助凝特性

采用在活化硅酸制备过程中加入适量TiCl4的方法,试制了一种新型无机高分子助凝剂—聚硅酸钛。研究了不同/条件下制备的聚硅酸钛在固定pH值的水中分散物的粒径和Zeta电位随着活化时间的变化趋势,并与活化硅酸作比较。结果表明,在Si/Ti=20,活化48 h的条件下能制备出较为稳定的聚硅酸钛。与活化硅酸相比,聚硅酸钛在水中的分散物具有较大的粒径和更高的Zeta电位。通过对比制备的活化硅酸和聚硅酸钛的红外图谱发现,聚硅酸钛中有Ti-O-Si键,证明钛离子参与了聚合反应,新生成的化学键提高了它的聚合度和稳定性。采用硫酸铝为混凝剂,聚硅酸钛为助凝剂进行混凝除浊实验。测定了絮凝体的Zeta电位和混凝沉淀后的上清液浊度,研究了硫酸铝投加量和混凝pH对聚硅酸钛助凝效果的影响。结果表明,投加适量的聚硅酸钛助凝剂,明显提高了混凝除浊效果且拓宽了有效混凝pH值的范围。     

PVC/PES-g-PEGMA共混膜的制备及其耐污染性能

首先将聚乙二醇单甲基甲醚酯(PEGMA)接枝到聚醚砜(PES)上得到PES-g-PEGMA,然后利用溶液共混的方法,将聚氯乙烯(PVC)与PES-g-PEGMA共混,通过溶剂-非溶剂扩散诱导相分离法(NIPS)制备PVC/PES-g-PEGMA共混膜。在此基础上对PVC/PES-g-PEGMA共混膜的断面和表面微观结构、水通量、 截留率、机械性能及耐污染等性能进行测试,并采用接触角,含水率(EWC),X 射线光电子能谱仪(XPS) 来表征PES-g-PEGMA 的质量百分含量对 PVC/PES-g-PEGMA 共混膜亲水性的影响。结果表明,PVC/PES-g-PEGMA共混膜水通量,亲水性较纯PVC有很大程度的提高。耐污染性实验表明,随着PES-g-PEGMA的增加,耐污染性逐渐增强。实验结果同时也表明,该共混体系最佳共混比为7:3。     

不同好氧预处理方式对餐厨垃圾产甲烷的影响

为了研究不同好氧预处理方式对餐厨垃圾厌氧消化产甲烷的影响,通过建立3个模拟厌氧生物反应器,研究了传统厌氧生物反应器C1、上层好氧预处理-厌氧生物反应器C2和底部好氧预处理-厌氧生物反应器C3 3种不同操作条件下的产甲烷过程。结果表明,挥发性有机酸的累积使C1始终处于产甲烷滞后阶段;而C2、C3的好氧预处理通过加快易水解酸化组分和过量挥发性有机酸的好氧降解,有效缓解了酸性抑制,产甲烷滞后时间明显缩短至10 d内。第32天C2停止上层曝气后,在27 d内甲烷浓度达到了50%以上,同时,产甲烷速率迅速上升,并在第81天可达到峰值773 mL/(kg·d)。C3在第11天停止底部曝气后,虽然经过22 d的时间甲烷浓度即上升至50%,但之后产甲烷速率经历回落阶段后再次逐渐上升,在实验结束时仅达到517 mL/(kg·d)。上层曝气的好氧预处理方式所需曝气时间相对较长,但其产甲烷启动快,与底部曝气相比,其后期的甲烷化过程更稳定并可达到较高的产甲烷速率。     

Comprehensive Environmental Investigation at Former Industrial/Petroleum Underground Storage Tank Sites in Long Beach,CA: A Forensic Perspective

Two industrial sites were investigated based on years of available hydrogeologic information and monitoring data for soil and groundwater. Collected data were forensically evaluated using age-dating and fingerprinting methods. The previous business uses of the project sites were as a gas station, laundry/dry-cleaning service, and car wash with petroleum underground storage tanks (USTs). As a result, these sites were exposed to a number of toxic contaminants at relatively high concentrations. Source control was necessary for successful remediation and the ultimate removal of the remaining compounds from these industrial sites. Although contaminated soil around the source was excavated during the remedial action and the high concentrations of contaminants were reduced, typical groundwater contaminants such as petroleum hydrocarbons as gasoline (TPH-G), benzene, toluene, ethylbenzene, xylenes (BTEX), and oxygenates including methyl tert-butyl ether (MTBE), diisopropyl ether (DIPE), ethyl tert-butyl ether (ETBE), tert-amyl methyl ether (TAME), and tert-butyl alcohol (TBA) were persistently found at the studied sites around the source points. The plume and concentration of contaminants had changed their shapes and strength for all monitoring periods. Thus, additional source control seems to be a requirement for the complete removal of source contamination, which must be ascertained with groundwater and soil monitoring on a regular time base. For the study sites, monitored natural attenuation was relatively feasible for the long-term plan; however, it did not offer a perfect remediation solution for an ultimate goal because of residual toxic compounds that might have affected the surrounding residential areas at higher concentrations than their health limits. Therefore, as a remediation strategy, the combination of clean-up technology and natural attenuation with monitoring activities are more highly recommended than either clean-up or natural attenuation used separately.