铁氧化物复合氧化铝催化臭氧化过程中溴酸盐的生成控制

以市售活性炭、硅藻土和氧化铝小球为载体,考察了负载铁基活性组分对催化臭氧化过程中溴酸盐的控制情况,其中,铁基复合氧化铝小球体现出更好的溴酸盐还原特性和催化剂稳定性,证实催化剂中铁氧化物是溴酸盐得到有效控制的主要活性组分。进一步考察了铁基复合氧化铝小球催化臭氧化处理实际原水过程中对溴酸盐的生成控制,以及反应过程中溶解性有机碳（DOC）的去除情况。结果表明,与单独臭氧化相比,该催化剂既能有效去除水中的溶解性有机物,又能明显抑制溴酸盐的生成,反应50h,其活性并没有明显下降。催化剂失活主要归因于吸附位点数量的下降,可以通过负载铁氧化物来实现催化剂的再生。     

一株抗Cd~（2＋）菌株的筛选及其吸附性能

Cd2＋为一种毒性金属元素,为了实际解决污水中低浓度重金属污染,实现污水达标排放,通过12C6＋重离子束辐照诱变技术筛选到一株耐受Cd2＋的菌株C2,研究其对Cd2＋的抗性和低浓度Cd2＋的吸附性能表明,Cd2＋浓度≤100 mg/L时,C2菌株可以生长繁殖,但随Cd2＋浓度升高受到抑制;SEM分析表明,受到Cd2＋胁迫时,C2产生大量胞外产物与Cd2＋形成络合物;吸附过程中菌粉表面空隙得到填充,形成凸起;红外光谱分析表明,吸附过程中的主要作用基团为醇羟基O—H键、氨基和酰胺基团;C2菌粉和固定化菌球都对Cd2＋有较好的吸附能力,菌粉吸附效果比固定化菌球稍好;菌粉和固定化吸附剂的最佳吸附初始pH值为5~6.0,最佳投加量分别为1.0 g/L和10 g/L（实际含菌量为1.0 g/L）;Cd2＋浓度在2~20mg/L时,在最佳吸附条件下,菌粉和固定化吸附剂对Cd2＋的吸附率均在90%左右;2种吸附剂吸附过程与Langmuir等温模型和拟二级动力学模型拟合最佳;热力学研究表明吸附反应均能自发进行。以上研究结果表明,C2菌粉和固定化吸附剂均可用于污水中低浓度Cd2＋的去除。     

南京某城市污水二级处理系统中酞酸酯类的分布及去除特征简

以南京某城市污水厂污水和污泥中的酞酸酯类（PAEs）为研究对象,分别采用固相萃取-气相色谱-质谱联用（SPE-GC-MS）和超声提取-气相色谱-质谱联用（USE-GC-MS）检测其中的优先控制污染物邻苯二甲酸二甲酯（DMP）、邻苯二甲酸二乙酯（DEP）、邻苯二甲酸二丁酯（DBP）和邻苯二甲酸单（2-乙基己基）酯（MEHP）,研究其在厌氧/好氧（A/O）污泥处理过程中的分布特征及降解规律。研究结果表明,各类PAEs在该污水厂的污水和污泥中均有检出,二级处理出水中4种酞酸酯类物质的浓度在0.151~2.419 μg/L。污水中4种酞酸酯的分布规律为MEHP>DBP>DMP>DEP,污泥中4种酞酸酯的分布规律为MEHP>DBP>DEP>DMP。该污水厂二级处理工艺对4种PAEs的去除效果较明显,去除效率DBP>DEP>DMP>MEHP。     

Ni2 +对活性污泥活性及群落多样性的影响简

通过检测活性污泥的电子传递体系活性以及生物多样性,研究Ni²⁺对活性污泥微生物活性及群落多样性的影响。结果表明：与对照系统相比,5 mg/L的Ni²⁺对2,3,5-triphenylteltrazolium chloride（TTC-ETS）活性未产生显著的影响;但当Ni²⁺的浓度进一步增大到10、20和40 mg/L后,其对序批式反应器内活性污泥TTC-ETS活性的抑制率分别达到（36.79±11.14）%、（55.88±13.90）%和（70.97±6.78）%。低浓度Ni²⁺能增强活性污泥微生物对碳源的利用,但高于10 mg/L的Ni²⁺则显著抑制了活性污泥微生物对碳源的利用。各个SBR系统中微生物群落最常见的物种相近,物种丰富度和均一性则均有所不同,其中群落物种丰富度随着Ni²⁺浓度的增加而逐渐减小。TTC-ETS活性、平均每孔颜色变化率、Shannon指数和Simpson指数,与Ni²⁺的胁迫浓度之间的显著相关性表明,它们均可有效地表征Ni²⁺胁迫对活性污泥微生物活性及群落多样性的影响程度。     

臭氧氧化6-APA制药厂生化处理出水的特性及动力学简

通过现场实验研究了6-APA制药厂生化处理出水的臭氧氧化特性及其动力学规律。结果表明,当臭氧浓度为27.5 mg/L,气水接触时间为80 min时,COD、UV₂₅₄、NH₃-N和色度的去除率分别可达72.95%、73.28%、72%和96.25%,达到《发酵类制药废水工业水污染物排放标准》（GB 21903-2008）排放控制要求。拟合结果表明,在0~10、10~30和30~90 min时段内,臭氧氧化过程遵循拟一级反应,但反应速率逐渐降低。当气水接触时间为30 min时,废水可生化性可由0.1提高至0.35,采用臭氧/生物处理的联合工艺也有望使出水达到相同的排放控制要求。     

CuO / 过硫酸氢钾体系催化氧化苯酚简

本论文通过直接沉淀法制备了CuO催化剂,结合过硫酸氢钾,在常温常压下催化氧化处理苯酚模拟废水。采用电子显微镜（SEM）、X射线粉末衍射（XRD）对催化剂进行了表征,并研究了反应过程中各影响因素对降解效率的影响。实验结果表明,在催化剂用量为0.2 g/L,氧化剂浓度为0.25 g/L,pH值为7,反应时间为60 min的条件下,浓度为50 mg/L的苯酚降解率可达100%,TOC去除率达84%。进一步实验表明,催化剂具有良好的重复使用能力。最后,通过自由基捕捉实验,考察了体系中的自由基种类,并根据实验结果,讨论了CuO/过硫酸氢钾体系的催化降解机理。     

Soil carbon and nitrogen dynamics in the first year following herbicide and scalping in a revegetation trial in south-east Queensland,Australia

During revegetation, the maintenance of soil carbon (C) pools and nitrogen (N) availability is considered essential for soil fertility and this study aimed to evaluate contrasting methods of site preparation (herbicide and scalping) with respect to the effects on soil organic matter (SOM) during the critical early establishment phase. Soil total C (TC), total N (TN), hot-water extractable organic C (HWEOC), hot-water extractable total N (HWETN), microbial biomass C and N (MBC and MBN), total inorganic N (TIN) and potentially mineralizable N (PMN) were measured over 53 weeks. MBC and MBN were the only variables affected by herbicide application. Scalping caused an immediate reduction in all variables, and the values remained low without any sign of recovery for the period of the study. The impact of scalping on HWETN and TIN lasted 22 weeks and stabilised afterwards. MBC and MBN were affected by both herbicide and scalping after initial treatment application and remained lower than control during the period of the study but did not decrease over time. While scalping had an inevitable impact on all soil properties that were measured, that impact did not worsen over time, and actually improved plant growth (unpublished data) while reducing site establishment costs. Therefore, it provides a useful alternative for weed control in revegetation projects where it is applied only once at site establishment and where SOM would be expected to recover as canopy closure is obtained and nutrient cycling through litterfall commences.     

Enhanced degradation of ortho-nitrochlorobenzene by the combined system of zero-valent iron reduction and persulfate oxidation in soils

ortho-Nitrochlorobenzene (o-NCB) in soil poses significant health risks to human because of its persistence and high toxicity. The removal of o-NCB by both zero-valent iron (ZVI) and chemical oxidation (persulfate) was investigated by batch experiments. The o-NCB removal rate increases significantly from 15.1 to 97.3 % with an increase of iron dosage from 0.1 to 1.0 mmol g^?1. The o-NCB removal rate increases with the decrease of the initial solution pH, and a removal efficiency of 90.3 % is obtained at an initial pH value of 6.8 in this combined system. It is found that temperature and soil moisture could also increase the o-NCB removal rate. The o-NCB degradation rate increases from 83.9 to 96.2 % and from 41.5 to 82.4 % with an increase of temperature (15 to 35 °C) and soil moisture (0.25 to 1.50 mL g^?1), respectively. Compared to the persulfate oxidation system and ZVI system, the persulfate–iron system shows high o-NCB removal capacity. o-NCB removal rates of 41.5 and 62.4 % are obtained in both the persulfate oxidation system and the ZVI system, while the removal rate of o-NCB is 90.3 % in the persulfate–iron system.     

The combined effects of urea application and simulated acid rain on soil acidification and microbial community structure

Our aim was to test the effects of simulated acid rain (SAR) at different pHs, when applied to fertilized and unfertilized soils, on the leaching of soil cations (K, Ca, Mg, Na) and Al. Their effects on soil pH, exchangeable H⁺ and Al³⁺ and microbial community structure were also determined. A Paleudalfs soil was incubated for 30 days, with and without an initial application of urea (200 mg N kg^?1soil) as nitrogen (N) fertilizer. The soil was held in columns and leached with SAR at three pH levels. Six treatments were tested: SAR of pH 2.5, 4.0 and 5.6 leaching on unfertilized soil (T1, T2 and T3), and on soils fertilized with urea (T4, T5 and T6). Increasing acid inputs proportionally increased cation leaching in both unfertilized and fertilized soils. Urea application increased the initial Ca and Mg leaching, but had no effect on the total concentrations of Ca, Mg and K leached. There was no significant difference for the amount of Na leached between the different treatments. The SAR pH and urea application had significant effects on soil pH, exchangeable H⁺ and Al³⁺. Urea application, SAR treated with various pH, and the interactions between them all had significant impacts on total phospholipid fatty acids (PLFAs). The highest concentration of total PLFAs occurred in fertilized soils with SAR pH5.6 and the lowest in soils leached with the lowest SAR pH. Soils pretreated with urea then leached with SARs of pH 4.0 and 5.6 had larger total PLFA concentrations than soil without urea. Bacterial, fungal, actinomycete, Gram-negative and Gram-positive bacterial PLFAs had generally similar trends to total PLFAs.     

Medium optimization for the production of anti-cyanobacterial substances by Streptomyces sp. HJC-D1 using response surface methodology

Bioremediation using isolated anti-cyanobacterial microorganism has been widely applied in harmful algal blooms (HABs) control. In order to improve the secretion of activated anti-cyanobacterial substances, and lower the cost, a sequential optimization of the culture medium based on statistical design was employed for enhancing the anti-cyanobacterial substances production and chlorophyll a (Chl a) removal by Streptomyces sp. HJC-D1 in the paper. Sucrose and KNO₃ were selected as the most suitable carbon and nitrogen sources based on the one-at-a-time strategy method, and sucrose, KNO₃ and initial pH were found as major factors that affected the anti-cyanobacterial ability of the isolated stain via the Plackett–Burman design. Based on the response surface and canonical analysis, the optimum condition of culture medium was obtained at 22.73 g l^-1 of sucrose, 0.96 g l^-1 of KNO₃, and initial pH 8.82, and the Chl a removal efficiency by strain HJC-D1 increased from 63?±?2 % to 78?±?2 % on the optimum conditions.