A major challenge in recycling of silicon powder from kerf loss slurry waste is the complete removal of metal particles. The traditional acid leaching method is costly and not green. In this paper, a novel approach to recover high-purity Si from the kerf loss slurry waste of solar grade silicon was investigated. The metal impurities were removed with superconducting high gradient magnetic separation technology. The effects of process parameters such as magnetic flux density, slurry density, and slurry flow velocity on the removal efficiency were investigated, and the parameters were optimized. In one lot of control experiments, the silicon content was increased from 90.91 to 95.83%, iron content reduced from 3.24 to 0.57%, and aluminum content from 2.44 to 1.51% under the optimum conditions of magnetic flux density of 4.0 T, slurry density of 20 g/L, and slurry flow velocity of 500 mL/min. The result indicates that the superconducting high gradient magnetic separation technology is a feasible purifying method, and the magnetic separation concentrate could be used as an intermediate product for high-purity Si powder.
Journal of Material Cycles and Waste Management - This work aims to develop another approach to the management of magnesium slag (MS) via the production of Portland cement clinker. Thus, 0, 10, 20,... 相似文献
Water supply reliability is expected to be affected by both precipitation amount and distribution changes under recent and future climate change. We compare historical (1951‐2010) changes in annual‐mean and annual‐maximum daily precipitation in the global set of station observations from Global Historical Climatology Network and climate models from the Inter‐Sectoral Impact Model Intercomparison Project (ISI‐MIP), and develop the study to 2011‐2099 for model projections under high radiative forcing scenario (RCP8.5). We develop a simple rainwater harvesting system (RWHS) model and drive it with observational and modeled precipitation. We study the changes in mean and maximum precipitation along with changes in the reliability of the model RWHS as tools to assess the impact of changes in precipitation amount and distribution on reliability of precipitation‐fed water supplies. Results show faster increase in observed maximum precipitation (10.14% per K global warming) than mean precipitation (7.64% per K), and increased reliability of the model RWHS driven by observed precipitation by an average of 0.2% per decade. The ISI‐MIP models show even faster increase in maximum precipitation compared to mean precipitation. However, they imply decreases in mean reliability, for an average 0.15% per decade. Compared to observations, climate models underestimate the increasing trends in mean and maximum precipitation and show the opposite direction of change in reliability of a model water supply system. 相似文献
EGR is one of the most significant strategies for reducing especially nitrogen oxides (NOx) emissions from internal combustion engines. The thermal efficiency of spark ignition engines is lower than compression ignition engines because of its lower compression ratio. If the compression ratio is increased to obtain higher thermal efficiency, there may be a knocking tendency in spark ignition engines. EGR can be used in order to reduce NOx emissions and avoid knocking phenomena at higher compression ratios. In-cylinder temperature at the end of combustion is decreased and heat capacity of fresh charge is increased when EGR applied. Besides EGR, spark timing is another significant parameter for reducing exhaust emissions such as nitrogen oxides, and unburned hydrocarbon (UHC). In this study the effects of EGR and spark timing on spark ignition engine were investigated numerically. KIVA codes were used in order to model combustion process. The combustion process has been modeled for a single cylinder, four stroke and gasoline direct injection (GDI) spark ignition engine. The results showed that in-cylinder pressure and heat release rate decrease as EGR ratio increase. In-cylinder pressure increases with the advancing of spark timing. Advancing spark timing increases the heat release rate and in-cylinder temperature. The simulation results also showed that EGR reduced exhaust gas temperature and NOx emissions. 相似文献
The residual levels of phthalate esters (PAEs) in the surface and two core sediments from Lake Chaohu were measured with a gas chromatograph–mass spectrometer (GC–MS). The temporal–spatial distributions, compositions of PAEs, and their effecting factors were investigated. The results indicated that di-n-butyl phthalate (DnBP), diisobutyl phthalate (DIBP), and di(2-ethylhexyl) phthalate (DEHP) were three dominant PAE components in both the surface and core sediments. The residual level of total detected PAEs (∑PAEs) in the surface sediments (2.146?±?2.255 μg/g dw) was lower than that in the western core sediments (10.615?±?9.733 μg/g) and in the eastern core sediments (5.109?±?4.741 μg/g). The average content of ∑PAEs in the surface sediments from the inflow rivers (4.128?±?1.738 μg/g dw) was an order of magnitude higher than those from the lake (0.323?±?0.093 μg/g dw), and there were similar PAE compositions between the lake and inflow rivers. This finding means that there were important effects of PAE input from the inflow rivers on the compositions and distributions of PAEs in the surface sediments. An increasing trend was found for the residual levels of ΣPAEs, DnBP, and DIBP from the bottom to the surface in both the western and eastern core sediments. Increasing PAE usage with the population growth, urbanization, and industrial and agricultural development in Lake Chaohu watershed would result in the increasing production of PAEs and their resulting presence in the sediments. The significant positive relationships were also found between the PAE contents and the percentage of sand particles, as well as TOC contents in the sediment cores. 相似文献