ABSTRACT Refrigerant pressure drop and temperature change in pipes are normally ignored in the thermodynamic analysis of traditional vehicle air conditioning system, this will result in serious errors. In this Paper, pressure drop and temperature difference are simulated in different pipes of electric vehicle (EV) heat pump system to analysis the effects of pipes in the actual EV heat pump system. The results indicate that the greater the mass flow, the faster pressure drop increases, the temperature difference decreases. Pressure drop of saturated liquid refrigerant is smaller than that of saturated gas refrigerant at the same saturation pressure and mass flow rate. The higher the refrigerant pressure (no phase change), the slower pressure drop decreases, the faster the temperature difference decreases. Pressure drop decreases with the increment of bending angle of the pipe. For EV heat pump system, suitable valves and less branches are helpful for energy saving of the system. Shortening the pipe between compressor and condenser can reduce temperature change obviously. Pressure drop per unit length in the pipe between evaporator and compressor is large especially in heating mode because of lower refrigerant density. It even reaches to over 100 times of that in the pipe between condenser and throttle valve in heating mode and has negative effects on the performance of the system. If the evaporator is closer to the compressor and the number of branches is less, then pressure drop will decrease a lot, which will be advantageous for energy saving of the heat pump system. 相似文献
• Selective molecularly imprinted polymer (MIP) binding gel was prepared.• MIP-DGT showed excellent uptake performance for antibiotics.• In situ measurement of antibiotics in wastewaters via MIP-DGT was developed.• The MIP-DGT method was robust, reliable, and highly sensitive. Urban wastewater is one of main sources for the introduction of antibiotics into the environment. Monitoring the concentrations of antibiotics in wastewater is necessary for estimating the amount of antibiotics discharged into the environment through urban wastewater treatment systems. In this study, we report a novel diffusive gradient in thin films (DGT) method based on molecularly imprinted polymers (MIPs) for in situ measurement of two typical antibiotics, fluoroquinolones (FQs) and sulfonamides (SAs) in urban wastewater. MIPs show specific adsorption toward their templates and their structural analogs, resulting in the selective uptake of the two target antibiotics during MIP-DGT deployment. The uptake performance of the MIP-DGTs was evaluated in the laboratory and was relatively independent of solution pH (4.0–9.0), ionic strength (1–750 mmol/L), and dissolved organic matter (DOM, 0–20 mg/L). MIP-DGT samplers were tested in the effluent of an urban wastewater treatment plant for field trials, where three SA (sulfamethoxazole, sulfapyridine, and trimethoprim) and one FQ (ofloxacin) antibiotics were detected, with concentrations ranging from 25.50 to 117.58 ng/L, which are consistent with the results measured by grab sampling. The total removal efficiency of the antibiotics was 80.1% by the treatment plant. This study demonstrates that MIP-DGT is an effective tool for in situ monitoring of trace antibiotics in complex urban wastewaters. 相似文献
The sigma (SIG) coordinate system in ocean circulation simulation models results inevitably in horizontal pressure gradient error. This problem also emerges in models of deep lakes or reservoirs with the same characteristics of underwater terrain mutation. SIG coordinates reflect vertical relative stratification but cannot be used to calculate horizontal pressure gradient force in places with drastic topographic changes; this results in vertical water temperature and circulation errors. In deep lakes or reservoirs, differences in water density caused by the temperature difference between upper and lower water bodies is the primary cause of thermal stratification phenomena. Lake Mead was used as a case study on steep topography based on Environmental Fluid Dynamics Code (EFDC) model in this study. SIG coordinates result in close agreement between the calibrated temperature time series at the top and middle water layers, but disparity in the bottom water layer. The error emerges in the horizontal pressure gradient error due to the SIG coordinate transformation. Neither increasing the vertical resolution nor adjusting the horizontal viscosity coefficient resolve this error. We test the sigma-zed (SGZ) coordinate which combines Z coordinate and SIG coordinate as a replacement for the SIG coordinate to find that they effectively reduce the model’s runtime and simulation efficiency. The vertical temperature distribution in SGZ coordinate mode is more accurate than the distribution in SIG coordinate mode. The Navier-Stokes horizontal gradient and advection diffusion equation results under SIG coordinates are very sensitive to the pressure gradient. The replacement also enhances resolution near the thermocline, facilitates reclosing of the water bottom and the equal sigma surface, lends significant advantages in terms of vertical temperature in the simulation for local deep water with steep terrain, and shortens runtime for 0.14 h. SGZ mixed coordinates are recommended in the simulation of deep lakes or reservoirs wherein the underwater topography is large (with abundant continuous deep trenches or reefs).
