高铝粉煤灰提取氧化铝后硅钙渣用作水泥混合材

为了使高铝粉煤灰提取氧化铝后所产生的硅钙渣被大量的用作水泥混合材,通过水泥强度、水化放热和干缩性实验研究了原状硅钙渣和脱碱硅钙渣对水泥强度和稳定性的影响。结果表明,当硅钙渣掺量达30%时,硅钙渣水泥强度仍可满足P·C 32.5水泥要求。且随硅钙渣掺入量的增加,水泥早期水化放热速率增加的同时水泥累计水化放热量和干缩率还会显著降低。与原状硅钙渣相比,在同等掺量的情况下,脱碱硅钙渣更有利于保持水泥强度,降低其水化热和改善干缩性。     

内源电子受体产生及其在抑制富磷剩余污泥释磷行为中的应用

根据生物脱氮除磷系统产生的富磷剩余污泥含有硝化细菌和生产废水含有高浓度氨氮的特点,将生产废水中的氨氮转化为硝酸盐(内源电子受体),并将获得的内源电子受体利用在富磷剩余污泥浓缩过程,同步实现内源电子受体反硝化及其抑制富磷剩余污泥释磷行为。结果表明,将富磷剩余污泥(excess activated sludge,EAS。EAS1是在好氧方式下添加,EAS2是在缺氧方式下添加)与生产废水(reject water)按4种比例(Ⅰ、生产废水∶EAS1∶EAS2=15%∶85%∶0%;Ⅱ、生产废水∶EAS1∶EAS2=15%∶80%∶5%;Ⅲ、生产废水∶EAS1∶EAS2=15%∶75%∶10%;Ⅳ、生产废水∶EAS1∶EAS2=15%∶65%∶20%)混合曝气用于产生内源电子受体时,最佳硝化时间均为12 h,可将液相中的氨氮分别由初始的(113.16±0.85)mg/L、(117.18±4.39)mg/L、(129.48±4.85)mg/L及(142.53±0)mg/L降至(0.74±0.41)mg/L、(0.45±0.15)mg/L、(0.41±0.15)mg/L及(0.38±0.08)mg/L;同时,硝酸盐氮分别由初始的(7.48±7.91)mg/L、(12.87±5.81)mg/L、(12.87±5.81)mg/L及(13.55±6.18)mg/L升为(128.37±11.03)mg/L、(141.43±12.71)mg/L、(148.01±14.84)mg/L及(146.22±7.53)mg/L。内源电子受体可将重力浓缩过程中释磷量分别削减85%、63%、64%及83%,同时使得由生产废水回流引起的氨氮积累量分别减少89.25%、69.93%、74.31%及85.40%。在整个内源电子受体产生及其应用于抑制污泥释磷阶段,TN去除率分别为39.59%、44.54%、51.86%及57.33%。上述内源电子受体胁迫条件下的浓缩过程中,不仅可以有效降低由重力浓缩释磷引起的磷积累量,且可同步实现减少由生产废水回流引起的氨氮积累量。     

煅烧的水滑石同时去除水体中砷和氟

为探讨水滑石类材料对水体中氟、砷离子的同时去除效果,采用共沉淀法合成(Mg∶Al=2∶1)纳米类水滑石(LDHs),用傅立叶转换红外光谱、电子扫描透射电镜、X射线晶体衍射等手段对合成的材料进行了表征,并研究纳米材料在不同初始浓度、pH、吸附时间、阴离子干扰条件下其同时除砷氟性能。结果表明,煅烧后的水滑石(LDOs)对砷最大吸附量为51.02 mg/g,对氟最大吸附量为36.63 mg/g。吸附动力学实验表明,煅烧水滑石对砷的吸附在前6 h内基本完成,对氟的吸附在前10 h内基本完成。砷氟共存溶液保持pH=4~10及pH=6~8时,水滑石分别对砷、氟保持良好的吸附效率。对比不同阴离子对水滑石共除砷氟效率的影响,水滑石除砷速率受到阴离子影响力大小为:HPO2-4CO2-3NO-3Cl-SO2-4;水滑石除氟速率受到阴离子影响力大小为:CO2-3HPO2-4SO2-4Cl-NO-3。材料再生循环利用4次后,对砷和氟的吸附效率均能达到90%以上。实验结果表明,所合成的水滑石是一种优秀的能共除砷氟的吸附剂。     

辉光放电等离子体氧化降解水中邻苯二甲酸二丁酯

研究了辉光放电等离子体降解水中典型的环境内分泌干扰物邻苯二甲酸二丁酯(DBP)及降解过程中过氧化氢(H2O2)的生成规律。考察了电解质种类、共存污染物(甲醇、叔丁醇)及催化剂等条件对DBP降解及H2O2生成的影响。结果表明,在硫酸钠溶液中DBP降解效率和H2O2生成速率最高;甲醇、叔丁醇等共存污染物对DBP降解和H2O2生成有抑制作用;Fe2+,Fe3+和Cu2+对DBP的降解有催化作用,其催化效果为Fe2+>Fe3+>Cu2+。用高效液相色谱、离子色谱及气质联用仪等仪器分析了降解中间产物,提出了可能的降解机理。     

酸性洗涤塔-生物滤塔-生物曝气池组合工艺处理恶臭气体NH3和H2S

采用酸性洗涤塔、生物滤塔和生物曝气池的组合工艺处理NH3、H2S恶臭混合气体,研究表明,该组合工艺对NH3和H2S有很好的去除效果,在进气流量为35 L/min,喷淋量45 L/h时,NH3进气浓度50.15~525.4 mg/m3,H2S进气浓度10.23~110.36 mg/m3时,NH3单一进气去除率稳定在99%以上,H2S单一进气去除率90%以上。混合进气后,NH3去除率几乎为100%,H2S的去除率提高至98%以上。在一定的浓度范围内,NH3和H2S之间的相互作用对两者的去除效果没有明显的影响,而且起到了相互促进降解的作用。同时,进气流量和填料层高度都会影响NH3、H2S的去除率。系统对进气容积负荷变化的缓冲能力强,在偶尔超负荷条件下运行并不能使系统崩溃,并且微生物对高负荷逐渐表现出适应性。大部分溶于水的氨由生物曝气池去除,去除率达到96.9%。     

聚丙烯酸钠作为调理剂对好氧堆肥的保氮影响

实验以污泥、锯末、猪粪为原料,以聚丙烯酸钠(PAAS)为调理剂,利用自制好氧堆肥反应器,研究了PAAS在污泥好氧堆肥中的保氮效果。实验显示,PAAS会提高堆体的pH水平,抑制氨氮的生成,从而减少NH3的挥发源,在PAAS对水溶性氨的吸附作用下,堆肥产品的最终氨氮水平依然得到提高;PAAS对硝化反应有一定的促进作用,添加PAAS的堆体在堆肥周期内的硝氮平均增幅可达到未添加PAAS的空白堆体的4.64倍;添加PAAS的堆体在堆肥周期内全氮平均降幅只有空白堆体的52.24%。PAAS做为堆肥调理剂起到了较为明显的保氮效果。     

Chemical oxidation of sulfadiazine by the Fenton process: Kinetics,pathways, toxicity evaluation

This paper investigated sulfadiazine oxidation by the Fenton process under various reaction conditions. The reaction conditions tested in the experiments included the initial pH value of reaction solutions, and the dosages of ferrous ions and hydrogen peroxide. Under the reaction conditions with pH 3, 0.25 mM of ferrous ion and 2 mM of hydrogen peroxide, a removal efficiency of nearly 100% was achieved for sulfadiazine. A series of intermediate products including 4-OH-sulfadiazine/or 5-OH-sulfadiazine, 2-aminopyrimidine, sulfanilamide, formic acid, and oxalic acid were identified. Based on these products, the possible oxidation pathway of sulfadiazine by Fenton's reagent was proposed. The toxicity evaluation of reaction solutions showed increased antimicrobial effects following the Fenton oxidation process. The results from this study suggest that the Fenton oxidation process could remove sulfadiazine, but also increase solution toxicity due to the presence of more toxic products.     

Modeling of Solid Particle Flow and Heat Transfer in Rotary Kiln Calciners

Abstract

Contaminated solid wastes exist in many industrial sites, gas plants, and oil refineries. One method of decontaminating the soil is to subject it to high temperatures in a rotary calciner in an anaerobic environment. Preliminary results from a computational model are presented in this paper for the flow and heat transfer from granular solid particles under treatment in a rotary kiln calciner. A fluidization model using kinetic theory of granular flow has been employed to solve the particle flow and heat transfer problem. While a two-dimensional model is used to predict the rotation induced flow of the solid particles, a pseudo three-dimensional model for heat transfer is developed where the axial bulk temperature gradient is obtained from a one-dimensional energy balance model. The model predictions indicate interesting features of the flow and temperature fields in the bed material. Future tasks include the development of a devolatilization model to study the decontamination of waste soil in the rotary calciner.     

Application and Evaluation of Two Air Quality Models for Particulate Matter for a Southeastern U.S. Episode

Abstract

The Models-3 Community Multiscale Air Quality (CMAQ) Modeling System and the Particulate Matter Comprehensive Air Quality Model with extensions (PMCAMx) were applied to simulate the period June 29–July 10, 1999, of the Southern Oxidants Study episode with two nested horizontal grid sizes: a coarse resolution of 32 km and a fine resolution of 8 km. The predicted spatial variations of ozone (O₃), particulate matter with an aerodynamic diameter less than or equal to 2.5 μm (PM_2.5), and particulate matter with an aerodynamic diameter less than or equal to 10 μm (PM₁₀) by both models are similar in rural areas but differ from one another significantly over some urban/suburban areas in the eastern and southern United States, where PMCAMx tends to predict higher values of O₃ and PM than CMAQ. Both models tend to predict O₃ values that are higher than those observed. For observed O₃ values above 60 ppb, O₃ performance meets the U.S. Environmental Protection Agency's criteria for CMAQ with both grids and for PMCAMx with the fine grid only. It becomes unsatisfactory for PMCAMx and marginally satisfactory for CMAQ for observed O₃ values above 40 ppb.

Both models predict similar amounts of sulfate (SO₄ ^2?) and organic matter, and both predict SO₄ ^2? to be the largest contributor to PM_2.5. PMCAMx generally predicts higher amounts of ammonium (NH₄ ⁺), nitrate (NO₃ ^?), and black carbon (BC) than does CMAQ. PM performance for CMAQ is generally consistent with that of other PM models, whereas PMCAMx predicts higher concentrations of NO₃ ^?,NH₄ ⁺, and BC than observed, which degrades its performance. For PM₁₀ and PM_2.5 predictions over the southeastern U.S. domain, the ranges of mean normalized gross errors (MNGEs) and mean normalized bias are 37–43% and –33–4% for CMAQ and 50–59% and 7–30% for PMCAMx. Both models predict the largest MNGEs for NO₃ ^? (98–104% for CMAQ, 138–338% for PMCAMx). The inaccurate NO₃ ^? predictions by both models may be caused by the inaccuracies in the ammonia emission inventory and the uncertainties in the gas/particle partitioning under some conditions. In addition to these uncertainties, the significant PM overpredictions by PMCAMx may be attributed to the lack of wet removal for PM and a likely underprediction in the vertical mixing during the daytime.     

Biofiltration Control of Hydrogen Sulfide 1. Design and Operational Parameters

Laboratory scale biological filter systems for control of hydrogen sulfide (H₂S) in waste gas have been studied and the optimum design and operating parameters determined. Extensive tests have been conducted to evaluate the effect of various filter bed operating parameters such as temperature, retention time, H₂S concentration, and H₂S loading rate. Variable properties of new and used composts such as sulfate content, acidity, and water content have been studied for their influence on H₂S removal efficiency. The effects of compost particle size distribution on system pressure drop and the maximum H₂S elimination capacity were examined. Biofiltration systems containing various types of yard waste compost as the filter material have been observed to remove hydrogen sulfide with efficiencies greater than 99.9 percent for H₂S inlet concentrations in the range from 5 to 2650 ppmv.