汽车用聚合物材料火灾燃烧特性研究

为研究车用聚合物材料的燃烧特性,并对材料的火灾危险性进行全方位的评估,采用锥形量热仪,对汽车上常用的ABS,PP-PVC,PVC革-无纺毡以及无纺布-PVC聚合物材料进行分析表征,测得点燃时间、热释放速率、总热释放量、质量损失速率、烟气生成速率等参数。结果表明:ABS材料的点燃危险性相对最低,PVC革-无纺毡材料相对最高;随热辐射强度的增加,各样品的热释放速率和烟气生成速率明显加快;结合热释放速率峰值、均值和总热释放量可知,无纺布-PVC材料的热危险性相对最低;结合烟气生成速率和总烟释放量可知,ABS材料的发烟危害性相对最高,无纺布-PVC的相对最低;综合比较各样品的FGI和FPI值,安全等级由高到低依次为ABS,PP-PVC,PVC革-无纺毡,无纺布-PVC。     

国产铝合金表面涂层体系在多因素综合加速试验条件下的老化规律研究

研究了一种国产新型铝合金表面防护体系在多因素协同加速试验条件下的表面性能变化规律。涂层在0.01 Hz处的阻抗模值由初始的1.88×10~9 Ω下降为2.04×10~7 Ω。经历5个周期的户内多因素综合加速试验的过程中,2A97铝合金表面涂层体系的防护效果呈持续下降趋势,但5周期后尚未完全失效。     

Effect of pipes in heat pump system on electric vehicle energy saving

ABSTRACT

Refrigerant pressure drop and temperature change in pipes are normally ignored in the thermodynamic analysis of traditional vehicle air conditioning system, this will result in serious errors. In this Paper, pressure drop and temperature difference are simulated in different pipes of electric vehicle (EV) heat pump system to analysis the effects of pipes in the actual EV heat pump system. The results indicate that the greater the mass flow, the faster pressure drop increases, the temperature difference decreases. Pressure drop of saturated liquid refrigerant is smaller than that of saturated gas refrigerant at the same saturation pressure and mass flow rate. The higher the refrigerant pressure (no phase change), the slower pressure drop decreases, the faster the temperature difference decreases. Pressure drop decreases with the increment of bending angle of the pipe. For EV heat pump system, suitable valves and less branches are helpful for energy saving of the system. Shortening the pipe between compressor and condenser can reduce temperature change obviously. Pressure drop per unit length in the pipe between evaporator and compressor is large especially in heating mode because of lower refrigerant density. It even reaches to over 100 times of that in the pipe between condenser and throttle valve in heating mode and has negative effects on the performance of the system. If the evaporator is closer to the compressor and the number of branches is less, then pressure drop will decrease a lot, which will be advantageous for energy saving of the heat pump system.     

典型有机磷酸酯阻燃剂分析方法研究进展

有机磷酸酯(OPEs)是一类重要的有机磷阻燃剂,近些年逐渐取代了溴代阻燃剂,广泛应用于各行各业,也因此导致在多种环境介质中有较高的暴露量和潜在风险。已有研究表明,OPEs具有一定的毒理效应,对人体及其他生物均有潜在危害。本文综述了近年来国内外OPEs的检测技术,详述了不同环境介质OPEs的前处理方法。结果表明,目前固相萃取(SPE)和固相微萃取(SPME)仍是水样前处理的主要方法;对于固体样品,加速溶剂萃取/加压液相萃取(ASE/PLE)和微波辅助萃取(MAE)应用较多;虽然大气样品仍以固体吸附剂方式为主,但已向在线一体化方向发展;而生物样品的前处理方法多与水样和固体样品方法相似;但是对于复杂环境介质中OPEs样品的前处理较为困难,方法有待改善;气相色谱-质谱联用(GC-MS)和气相色谱-氮磷检测器(GC-NPD)对弱极性和易挥发的OPEs分析效果好,而强极性和难挥发的OPEs多用液相色谱-质谱联用(LCMS);气相色谱-质谱串联(GC-MS/MS)、液相色谱-质谱串联(LC-MS/MS)和高效液相色谱-质谱串联(UPLC-MS/MS)等对多种复杂的环境介质中的OPEs均有较好的检测分析效果,但并未普及。最后,对OPEs分析测试方法的发展趋势提出了展望。     

天津市地表水体与沉积物中7种高关注酚类化合物的污染特征与生态风险分析

为探究地表水体与沉积物中酚类化合物的污染分布特征和生态风险,选择天津市3个水源地与6条主要河流,采集了26个地表水样与6个沉积物样品,利用固相萃取与超声萃取、高效液相色谱-串联质谱法(HPLC-MS/MS)测定了水样及沉积物中1-萘酚(1-naphthol)、壬基酚(nonylphenol, NP)、双酚A(bisphenol A, BPA)、2-苯基苯酚(biphenyl-2-ol)、3,4-二氯酚(3,4-dichlorophenol)、四溴双酚A(tetrabromobisphenol A, TBBPA)和对叔丁基苯酚(p-tert-butylphenol, PTBP)等7种高关注酚类化合物的浓度水平,并应用物种敏感性分布(species sensitivity distribution, SSD)法和熵值法(ecological risk quotient, RQ)评估7种酚类化合物水环境和沉积物的生态风险。结果表明,地表水样中7种酚类化合物均全部检出;其中壬基酚的检出浓度最高,其次为四溴双酚A、对叔丁基苯酚、1-萘酚、2-苯基苯酚、3,4-二氯酚和双酚A。沉积物中酚类化合物的污染分布规律与水样相似,除双酚A外的目标物全部检出。其中,壬基酚浓度比其他物质浓度高2个数量级。风险评估结果显示,壬基酚对水环境与沉积物存在不可接受的风险;而四溴双酚A、对叔丁基苯酚、1-萘酚、2-苯基苯酚、3,4-二氯酚和双酚A则对环境具有较低风险或者存在一定的风险。     

Utilization of MSWI fly ash as partial cement or sand substitute with focus on cementing efficiency and health risk assessment

• Washed MSWI fly ash was used as partial cement or sand substitute. • Sand replacing is beneficial for strength, while cement replacement reduces strength. • Cementing efficiency factor and mortar pore structure explain the strength results. • Health risk assessment was conducted for MSWI fly ash blended cement mortar. • CR and HI contributed by different exposures and heavy metals were analyzed. The strength of cement substituted mortar decreases with the increase in fly ash amount, whereas the strength increases when the fly ash is blended as sand substitute. A mortar with highest strength (compressive strength= 30.2 Mpa; flexural strength= 7.0 Mpa) was obtained when the sand replacement ratio was 0.75%. The k value (cementing efficiency) of fly ash varied between 0.36 and 0.15 for the fly ash fraction in binder between 5% and 25%. The k values of fly ash used for sand replacement were all significantly above that used for cement substitution. The macropores assigned to the gaps between particles decreased when the fly ash was used as sand replacement, providing an explanation for the strength enhancement. The waste-extraction procedure (toxicity-sulphuric acid and nitric acid method (HJ/T 299-2007)) was used to evaluate metal leaching, indicating the reuse possibility of fly ash blended mortar. For the mortar with the mass ratio of fly ash to binder of 0.5%, the carcinogenic risks (CR) and non-carcinogenic hazard quotient (HQ) in sensitive scenario for blended mortar utilization were 9.66 × 10^-7 and 0.06, respectively; these results were both lower than the threshold values, showing an acceptable health risk. The CR (9.89 × 10^-5) and HQ (3.89) of the non-sensitive scenario for fly ash treatment exceeded the acceptable threshold values, indicating health risks to onsite workers. The main contributor to the carcinogenic and non-carcinogenic risk is Cr and Cd, respectively. The CR and HQ from inhalation was the main route of heavy metal exposure.