华东典型城市非道路移动机械排气烟度

在华东地区典型城市开展了超过900台非道路移动机械的排气烟度实测工作,结合测试机械的属性调查,分析汇总了现阶段各类机械的排气烟度范围(包括光吸收系数和林格曼黑度),并定量研究了机械出厂年限、机械功率、测试工况及油品差异对机械排气烟度的影响.结果表明,在自由加速工况下,实测非道路移动机械的排气烟度为(1. 02±0. 57) m~(-1),林格曼黑度等级为2. 10±0. 19(无量纲),各类机械超过国家标准GB 36886-2018中关于烟度I限值比例为12%～25%; 80%的机械启动烟度大于自由加速烟度,且各类机械启动烟度约为自由加速排气烟度的2倍;与普通柴油相比,使用车用柴油可少量削减机械排气烟度均值,可显著削减或抑制排气烟度高值.启动时喷油量瞬间增加过快与油品质量较差可直接影响非道路用柴油机的排气烟度.     

顶空气相色谱法测定水和废水中的邻二氯苯

采用顶空采样,填充柱分离,ECD测定水和废水中的邻二氯苯,在柱温150℃,进样室温200℃,ECD温300％下,邻二氯苯的保留时间为3．78min,该方法灵敏度高,最低检出浓度为0．02μg／L;精密度好,对标准样品六次测定的相对标准偏差小于3．9％;准确度高,加标回收率在95％～104％之间。操作简便、测定快速,克服了萃取法烦琐、有毒、易污染色谱柱等缺点。     

黄磷尾气生产甲酸中尾气净化试验研究

通过综合研究试验筛选,研发专门适用以黄磷生产中外排废尾气为原料,匹配当今较先进的甲酸甲酯水解法(改进工艺)生产具有广泛用途和良好市场前景的环保型有机强酸———甲酸,完全满足优级甲酸生产的气体净化、提纯、提浓工艺技术,且安全可靠,经济合理。     

赤泥和污泥对土壤锌化学形态转化的影响

通过土壤室内培养实验,研究了赤泥和污泥对土壤中Zn化学形态转化的影响。研究表明:单独使用赤泥可以有效降低土壤中植物可利用态Zn含量,促进可交换态(EXC)、碳酸盐结合态(CA)、有机结合态(OM)转化为残渣态(RES),而污泥对Zn的固稳效果是暂时的。赤泥和污泥的一起使用较单独使用赤泥或污泥固稳Zn的效果好,既能促进有效态重金属Zn转化为不可利用态Zn,又能增加土壤肥力。     

Adsorption of carbon dioxide on amine-modified TiO2 nanotubes

TiO2 nanotubes (TiNT) were prepared by a hydrothermal treatment and modified by three kinds of amines,namely ethylenediamine,polyetherimide and tetraethylenepentamine (TEPA),to study their CO2 adsorption properties from gas streams.The resultant samples were characterized by X-ray diffraction,transmission electron microscopy,and infrared spectroscopy,as well as low temperature N 2 adsorption.CO2 capture was investigated in a dynamic packed column at 30℃.TEPA-modified TiO2 nanotubes showed the highest adsorption capacity of 167.64 mg/g because it had the highest amino-group content among the three amines.CO2 fixation on TiNT impregnated by TEPA was investigated at 30,50,and 70℃,and the adsorption capacity increased slightly with temperature.Following the adsorption step,the sorbents were regenerated by temperature programmed desorption,and the TiNT-TEPA sample,as CO2 sorbent,was found to be readily regenerated and energy-efficient.The cycle test also revealed that the TiNT-TEPA adsorbent is fairly stable,with only a 5% drop in the adsorption capacity after 10 adsorption/desorption cycles.In addition,the CO2 adsorption behavior was investigated with the deactivation model,and which showed an excellent prediction for the TiNT-TEPA breakthrough curves.     

Effect of bulk density of coking coal on swelling pressure

Coking coals are the important raw materials for the iron and steel industries and play an important role on its sustainable development, especially on the stamp-charging coke making with the characteristics of increasing the bulk density. There is a significance on the reasonable usage of the coking coal resource with the reduced production cost, improved efficiency of the economy to develop the stamp-charging coke making technology. Important effects of the density of coking coal on the coking and caking properties were investigated. In the article, the maximum values of swelling pressure and variation of Laowan gas coal and Xinjian 1/3 coking coal, Longhu fat coal and Didao coking coal, which were mined at Shenyang and Qitaihe respectively, were investigated under different bulk densities during the coking. The results showed that when the values of density increased from 0.85 ton/m³ to 1.05 ton/m³, for the Laowan gas coal, swelling pressure variation and even the maximum value changed slightly. The swelling pressure was 3.63 KPa when the density was improved to 1.05 ton/m³; for the Xinjian 1/3 coking coal, the values of swelling pressure changed significantly and the maximum values was 82.88 KPa with the density improved to 1.05 when the coal was heated to 600℃. The coke porosity, which was investigated by automatic microphotometer, decreased from 47.4% to 33.1% with the increasing of the density from 0.85 ton/m³ to 1.05 ton/m³, and the decreased value was 14.3%. Meanwhile, the pore structures of four cokes were characterized by an optical microscope.     

Nitrogen and phosphorus removal in an airlift intermittent circulation membrane bioreactor

A new airlift intermittent circulation integrated bioreactor was developed for simultaneous nitrogen and phosphorus removal of wastewater, in which, circulation of mixed liquid between mixing zone and aeration zone was realized by aeration power, alternately anaerobic/anoxic bio-environment in mixing zone was realized by intermittent circulation and simultaneous nitrogen and phosphorus removal was obtained through strengthened denitrifying phosphorus removal process. Removal performance of the reactor was investigated and pollutant removal and transfer mechanism in one operation circle was analyzed. The experiment results indicated that under the influent condition of chemical oxygen demand (COD) concentration of 642.1 mg/L, total nitrogen (TN) of 87.4 mg/L and PO₄^3--P of 12.1 mg/L, average removal efficiencies of COD, TN and PO₄^3--P reached 96.4%, 83.2% and 90.5%, respectively, with the hydraulic residence time of 22 hr and operation circle time of 185 min. Track studies indicated that the separation of aeration and mixing zones and intermittent circulation of mixed liquid between the two zones provided distinct biological environments spatially and temporally, which ensured the occurrence of multifunctional microbial reactions.     

Application of hinokitiol potassium salt for wood preservative

The decay of wood and other cellulosic materials by fungi cause significant economic loss. The widely used chromated copper arsenate was prohibited for the environmental impact and safety of arsenic and chromium. It was found that natural product hinokitiol (HK) had fungicidal and insecticidal activities, and its toxicity was bearable for the environment. We described the practical synthesis of HK-K salt. According to the GB/T18261-2000 and LY/T1283-1998, wood preservative performance of HK-K salt was tested. The results showed that the best inhibitory concentration of HK-K salt was 50 mg/L, for which the prevention effectiveness on mold is better, the killed value is between 0 and 1, and the corrosion-resistant for wood-rotting fungi is grade A.     

Effect of mass fraction of long flame coal on swelling pressure and microstructures of cokes

Long flame coal are abundant and widely distributed in China, but the resource utilization is quite low, the production efficiency is not high. Stamp-charging coke making technology can bend some long flame coal, which can reduce production cost and expand the coking coal resources. The long flame coal of different mass fraction is added into prime coking coal including fat coal from Longhu, 1/3 coking coal from Xinjian and coking coal from Didao in experiment. The swelling pressure is tested on-line detection using pressure sensor in coke making process, and the pores are observed by scanning electron microscopy. The results show that, the swelling pressure first increase and then decrease with the temperature increased and the maximum swelling pressure reduces gradually with mass fraction of the Long flame coal from Shenmu increased in coke making process. The SEM images of resultant coke display that the coke get more and more loose and the amount of pores is increased with mass fraction of the long flame coal from Shenmu increased. The amount pores and the pore diameter both is minimum for coking coal from Didao as prime coking coal under the same fraction of long flame coal.     

Effect of bulk density of coking coal on swelling pressure

Coking coals are the important raw materials for the iron and steel industries and play an important role on its sustainable development, especially on the stamp-charging coke making with the characteristics of increasing the bulk density. There is a significance on the reasonable usage of the coking coal resource with the reduced production cost, improved efficiency of the economy to develop the stamp-charging coke making technology. Important effects of the density of coking coal on the coking and caking properties were investigated. In the article, the maximum values of swelling pressure and variation of Laowan gas coal and Xinjian 1/3 coking coal, Longhu fat coal and Didao coking coal, which were mined at Shenyang and Qitaihe respectively, were investigated under different bulk densities during the coking. The results showed that when the values of density increased from 0.85 ton/m³ to 1.05 ton/m³, for the Laowan gas coal, swelling pressure variation and even the maximum value changed slightly. The swelling pressure was 3.63 KPa when the density was improved to 1.05 ton/m³; for the Xinjian 1/3 coking coal, the values of swelling pressure changed significantly and the maximum values was 82.88 KPa with the density improved to 1.05 when the coal was heated to 600°C. The coke porosity, which was investigated by automatic microphotometer, decreased from 47.4% to 33.1% with the increasing of the density from 0.85 ton/m³ to 1.05 ton/m³, and the decreased value was 14.3%. Meanwhile, the pore structures of four cokes were characterized by an optical microscope.