CFD simulation of MSW combustion and SNCR in a commercial incinerator

A CFD scheme was presented for modeling municipal solid waste (MSW) combustion in a moving-grate incinerator, including the in-bed burning of solid wastes, the out-of-bed burnout of gaseous volatiles, and the selective non-catalytic reduction (SNCR) process between urea (CO(NH₂)₂) and NO_x. The in-bed calculations provided 2-D profiles of the gas–solid temperatures and the gas species concentrations along the bed length, which were then used as inlet conditions for the out-of-bed computations. The over-bed simulations provided the profiles of incident radiation heat flux on the top of bed. A 3-dimensional benchmark simulation was conducted with a 750 t/day commercial incinerator using the present coupling scheme incorporating with a reduced SNCR reduction mechanism. Numerical tests were performed to investigate the effects of operating parameters such as injection position, injection speed and the normalized stoichiometric ratio (NSR) on the SNCR performance. The simulation results showed that the distributions of gas velocity, temperature and NO_x concentration were highly non-uniform, which made the injection position one of the most sensitive operating parameters influencing the SNCR performance of moving grate incinerators. The simulation results also showed that multi-layer injections were needed to meet the EU2000 standard, and a NSR 1.5 was suggested as a compromise of a satisfactory NO_x reduction and reasonable NH₃ slip rates. This work provided useful guides to the design and operation of SNCR process in moving-grate incinerators.     

Catalytic activities and mechanism of formaldehyde oxidation over gold supported on MnO<Subscript>2</Subscript> microsphere catalysts at room temperature

MnO₂ microspheres with various surface structures were prepared using the hydrothermal method, and Au/MnO₂ catalysts were synthesized using the sol-gel method. We obtained three MnO₂ microspheres and Au/MnO₂ samples: coherent solid spheres covered with wire-like nanostructures, solid spheres with nanosheets, and hierarchical hollow microspheres with nanoplatelets and nanorods. We investigated the properties and catalytic activities of formaldehyde oxidation at room temperature. Crystalline structures of MnO₂ are the main factor affecting the catalytic activities of these samples, and γ-MnO₂ shows high catalytic performance. The excellent redox properties are responsible for the catalytic ability of γ-MnO₂. The gold-supported interaction can change the redox properties of catalysts and accelerate surface oxygen species transition, which can account for the catalytic activity enhancement of Au/MnO₂. We also studied intermediate species. The dioxymethylene (DOM) and formate species formed on the catalyst surface were considered intermediates, and were ultimately transformed into hydrocarbonate and carbonate and then decomposed into CO₂. A proposed mechanism of formaldehyde oxidation over Au/MnO₂ catalysts was also obtained.     

The data not collected on community forestry

Conservation and development practitioners increasingly promote community forestry as a way to conserve ecosystem services, consolidate resource rights, and reduce poverty. However, outcomes of community forestry have been mixed; many initiatives failed to achieve intended objectives. There is a rich literature on institutional arrangements of community forestry, but there has been little effort to examine the role of socioeconomic, market, and biophysical factors in shaping both land‐cover change dynamics and individual and collective livelihood outcomes. We systematically reviewed the peer‐reviewed literature on community forestry to examine and quantify existing knowledge gaps in the community‐forestry literature relative to these factors. In examining 697 cases of community forest management (CFM), extracted from 267 peer‐reviewed publications, we found 3 key trends that limit understanding of community forestry. First, we found substantial data gaps linking population dynamics, market forces, and biophysical characteristics to both environmental and livelihood outcomes. Second, most studies focused on environmental outcomes, and the majority of studies that assessed socioeconomic outcomes relied on qualitative data, making comparisons across cases difficult. Finally, there was a heavy bias toward studies on South Asian forests, indicating that the literature on community forestry may not be representative of decentralization policies and CFM globally.     

Source-to-sink process and risk assessment of heavy metals for the surface sediment in the northern South China Sea

Environmental Science and Pollution Research - Heavy metal input from the coastal urbanization and industrialization and their potential ecological risks have been a great concern in the northern...     

含阶梯结构的高层楼梯井内烟气湍流及输运特征量的全局敏感性分析

高层建筑竖井火灾中影响因素众多,并且各因素对高层楼梯井火灾中重要现象、关键数值等的影响大小不一,使得此类火灾中的实验或理论研究成本较高。通过建立全局敏感性分析平台,定量考察了高层楼梯井结构所涉及因素的影响大小,并能够方便地筛选掉对所考察量影响较小的因素,以降低实验或计算成本。使用数值模拟方法,通过CFD软件对包含阶梯几何框架的高层楼梯井结构火灾进行了共计60次工况计算。并且根据计算结果,使用全局参数敏感性分析方法,得出建筑尺寸、热释放速率、环境参数对高层楼梯井内烟气湍流特性及输运特性的敏感性排序。结果表明,火源热释放速率对各输出参数的影响均占38%以上。     

Design and risk assessment tool for vegetative treatment areas receiving agricultural wastewater: Preliminary results

Vegetative treatment areas (VTAs) are commonly being used as an alternative method of agricultural process wastewater treatment. However, it is also apparent that to completely prevent discharge of pollutants to the surrounding environment, settling of particulates and bound constituents from overland flow through VTAs is not sufficient. For effective remediation of dissolved agricultural pollutants, VTAs must infiltrate incoming wastewater. A simple water balance model for predicting VTA soil saturation and surface discharge in landscapes characterized by sloping terrain and a shallow restrictive layer is presented and discussed. The model accounts for the cumulative effect of successive rainfall events and wastewater input on soil moisture status and depth to water table. Nash–Sutcliffe efficiencies ranged from 0.65 to 0.81 for modeled and observed water table elevations after calibration of saturated hydraulic conductivity. Precipitation data from relatively low, average, and high annual rainfall years were used with soil, site, and contributing area data from an example VTA for simulations and comparisons. Model sensitivity to VTA width and contributing area (i.e. barnyard, feedlot, silage bunker, etc.) curve number was also investigated. Results of this analysis indicate that VTAs should be located on steeper slopes with deeper, more-permeable soils, which effectively lowers the shallow water table. In sloping landscapes (>2%), this model provides practitioners an easy-to-use VTA design and/or risk assessment tool that is more hydrological process-based than current methods.     

Determination of trace metal concentrations in soil profiles of municipal waste dumps in Nigeria

The concentrations of trace metals (Cd, Pb, Cu, Cr, Fe, Ni, Zn and Co) were studied in soil profiles of eight municipal waste dump sites in Warri metropolis. The results indicate that concentrations of trace metals varied widely among the different dumpsites and decreased with depths in a studied soil profile. The accumulation pattern for the heavy metals in the soil profiles follows the order: Fe > Pb > Mn > Co > Cr > Zn > Ni > Cu > Cd. The concentrations of metals found in these sites was below the Canadian remediation criteria for land for agricultural, residential and commercial/industrial purposes except for the cadmium levels in some sites that exceeded criterion values for agricultural and residential. In such sites, remedial actions are required before any form of chosen development can take place. The levels of heavy metals found in these dump sites were higher than that of the control site. The examined metals showed no significant correlation with soil physicochemical properties at the surface horizon, which is suggestive evidence that these metals arise from anthropogenic input.     

Environmentally Friendly Polyurethane Composites: Preparation, Characterization and Mechanical Properties

The waterborne polyurethane (PU) prepolymer was prepared based on isophorone diisocyanate (IPDI), polyester polyol (N220), dimethylol propionic acid (DMPA) and hydroxyethyl methyl acrylate (HEMA). The modified waterborne polyurethane–acrylate (PUA) emulsions were obtained with different proportions of acrylate (butyl acrylate and methyl methacrylate) and initiating agent by in situ dispersion technique. The structures and thermal properties of prepared PU and PUA were analyzed and characterized with FT-IR, UV–Vis spectroscopy and DSC. The PUA hybrid samples had lower glass transition temperature of hard segment and higher decomposition temperatures than PU sample. Performances of the emulsion and film were studied by means of apparent viscidity, particle size and polydispersity, surface tension and mechanical properties. The results indicated that the particle sizes of the PUA dispersions were larger than those of the pure PU and the solvent resistance, mechanical properties of PUA films was improved compare with the unmodified polyurethane film. The film had the biggest hardness and the least water absorption when the BA/MMA mass ratio 5:5 modified PU. The obtained PUA have great potential application such as coatings, leather finishing, adhesives, sealants, plastic coatings and wood finishes.     

Critical Review of Norms and Standards for Biodegradable Agricultural Plastics Part II: Composting

The critical review of norms and standards and corresponding tests to determine the compostability of biodegradable plastics, possibly applicable also to biodegradable agricultural plastics, shows that many norms concerning testing and labelling of compostable plastics have been established at the international level. Some of them are about plastic materials, some others are about products like packaging. The media and conditions of testing cover mainly the conditions designed for industrial composting facilities, and only a few concern home composting conditions. Considering that the end of life management of biodegradable agricultural plastic products will be done at the farm to reduce the management of the waste and also its cost, only a few of these norms are considered to be suitable for adaptation to cover also biodegradable agricultural plastic products. The biodegradability validation criteria under composting conditions, such as the threshold percentage of biodegradation and disintegration, the time and temperature, and the ecotoxicity, are presented for the main norms and standard testing methods. Based on these different norms and their content, a list of specs and technical requirements that could be adapted to meet farm composting conditions for agricultural compostable plastics is proposed. These requirements may be used as criteria for the establishment of a new integrative norm for agricultural compostable plastics.     

活性碳纤维吸附废气中的丙烯酸和甲苯

采用动态吸附法探讨了在活性碳纤维对模拟废气中丙烯酸和甲苯的吸附过程中,各因素对活性碳纤维穿透吸附量和饱和吸附量的影响。实验结果表明,在模拟废气中丙烯酸质量分数为0.2%、双柱塞泵流量为6.1mL/h、载气流量为1.60L/min的条件下,穿透时间为10min,活性碳纤维的穿透吸附量为227.5mg/g,饱和吸附时间为40min,活性碳纤维的饱和吸附量为460.0m g/g。