Differences and similarities of gas and dust explosions: A critical evaluation of the European ‘ATEX’ directives in relation to dusts

Explosive gas mixtures and explosive dust clouds, once existing, exhibit similar ignition and combustion features. However, there are two basic differences between dusts and gases which are of substantially greater significance in design of safety standards than these similarities. Firstly, the physics of generation and up-keeping of dust clouds and premixed gas/vapour clouds are substantially different. This means that in most situations where accidental explosive gas clouds may be produced quite readily, generation of explosive dust clouds would be highly unlikely. Secondly, contrary to premixed gas flame propagation, the propagation of flames in dust/air mixtures is not limited only to the flammable dust concentration range of dynamic clouds. The state of stagnant layers/deposits offers an additional discrete possibility of flame propagation.

The two European Directives 94/9/EC (1994) and 1999/92/EC (1999) primarily address gases/vapours, whereas the particular properties of dusts are not addressed adequately. Some recent IEC and European dust standards resulting from this deficiency are discussed, and the need for revising the two directives accordingly is emphasized.     

Off-site emergency scenario, a case study from a LPG Bottling Plant

After Bhopal disaster, emergency planning in an industrial area has become inevitable. The off-site emergency plan is an integral part of any major hazard control system. Boiling Liquid Expanding Vapour Explosion (BLEVE) leads to fatal consequences. This paper highlights some salient features of the emergency scenario, which ultimately leads to fireball with enormous pressure wave all around.     

The interactive effects of conscientiousness,openness to experience,and political skill on job performance in complex jobs: The importance of context

Caveats concerning the ability of personality to predict job performance have been raised because of seemingly modest criterion‐related validity. The goal of the present research was to test whether narrowing the context via the type of job (i.e., jobs with complex task demands) and adding a social skill‐related moderator (i.e., political skill) would improve performance prediction. Further, along with political skill, the broad factor of personality demonstrated in prior research to have the strongest criterion validity (i.e., conscientiousness) was joined with a narrow construct closely related to openness to experience (i.e., learning approach) in a three‐way interactive prediction of supervisor‐rated task performance. With the employee–supervisor dyads among professionals, but not with the control group of non‐professional employees, task performance was predicted by the three‐way interaction, such that those high on all three received the highest performance ratings. Implications, strengths and limitations, and directions for future research are discussed. Copyright © 2012 John Wiley & Sons, Ltd.     

Experimental Verification of the Computerized Method for Work Space Optimization in Conditions of Static Work

The aim of this study was to verify a theoretical model for upper extremity work space optimization. In order to do that, experimental studies were conducted in which two parameters of the electromyography (EMG) signal were analyzed: AMP (amplitude calculated as Root Mean Square) and SZC (coefficient of the slope of the regression line between time and Zero Crossing values). Values of forces in muscles (parameter MOD) were calculated from theoretical studies. A comparison of experimental (AMP, SZC) and theoretical (MOD) parameters was performed by analyzing the coefficient of correlation between those parameters and differentiation of muscular load according to external load value. Analysis showed that the theoretical and experimental results are in step, which means that the developed model can be used for upper extremity work space optimization.     

Disparity of a Seat Cushion and Its Influence on Postural Control

Properties of supporting surfaces of a seat have an influence on postural control. Centre of pressure (COP) displacement parameters reflect both the balance controlling process and movements of the centre of a mass of entire body. The subjects of the study were 9 healthy men. A seat cushion was examined with a 2-force platform setup. Force exertion at a seat pan and feet and COP displacement at a seat pan were measured to analyse postural control. Analysis of variance determined the differences in postural control depending on a cushion type among the subjects. Significant differences in COP displacement parameters were in COP trajectory length, medio-lateral COP displacement and COP velocity. The results of the study showed that foam cushion ensures better postural control.     

Experimental investigation of hydrogen–air deflagrations and detonations in semi-confined flat layers

This paper presents results of an experimental investigation on the deflagration and deflagration-to-detonation transition (DDT) in an obstructed (blockage ratio BR = 50%), semi-confined flat layer filled with uniform hydrogen–air mixtures. The effect of mixture reactivity depending on flat layer thickness and its width is studied to evaluate the critical conditions for sonic flame propagation and the possibility for detonation onset. The experiments were performed in a transparent, rectangular channel with a length of 2.5 m. The flat layer thickness was varied from 0.06 to 0.24 m and the experiments were performed for different channel widths of 0.3, 0.6 and 0.9 m. The experimental results show flame velocity vs. hydrogen concentration for different thicknesses and widths of the semi-confined flat layer. Three different flame propagation regimes were observed: slow subsonic flame (M << 1), sonic deflagration (M ～ 1) and detonation (M >> 1). It is shown that flame acceleration (FA) to sonic speed is independent of the width of the flat layer. The critical expansion ratio for effective flame acceleration to sonic speed was found to be linearly dependent on the reciprocal layer thickness.     

Assessment of an accidental vapour cloud explosion: Lessons from the Indian Oil Corporation Ltd. accident at Jaipur,India

On 29 October 2009, at 19:30 IST, a devastating vapour cloud explosion occurred in a large fuel storage area at the Indian Oil Corporation (IOC) Depot in Jaipur, India, generating significant blast pressure. As a consequence of this explosion, the entire installation was destroyed, buildings in the immediate vicinity were heavily damaged, and windowpane breakages were found up to 2 km from the terminal. The IOC estimated that the total loss from the fire and explosion was approximately INR 2800 million.Ironically, as a storage site, the Jaipur terminal was not highly congested, and thus was not considered to have adequate potential for a vapour cloud explosion (VCE). Nevertheless, the prima facie evidences indicate that this was a case of VCE. Therefore, the main objective of this study is to quantify the potential overpressures due to vapour cloud explosions (VCEs) using the Process Hazard Analysis DNV Norway based PHAST 6.51 Software. The results are validated by the extent of the damage that had occurred. The estimation of the VCE shows that a maximum 1.0 bar overpressure was generated in the surrounding area. The initial assessment of the accident data roughly estimates the release mode, time, and amount of vaporized fuel. A more accurate estimate has been obtained by modelling the dispersion of vapour clouds in the surrounding atmosphere, which reveals trends and relationships for the occurrence of vapour cloud explosions.     

Predictive Model of Avian Electrocution Risk on Overhead Power Lines

Electrocution on overhead power structures negatively affects avian populations in diverse ecosystems worldwide, contributes to the endangerment of raptor populations in Europe and Africa, and is a major driver of legal action against electric utilities in North America. We investigated factors associated with avian electrocutions so poles that are likely to electrocute a bird can be identified and retrofitted prior to causing avian mortality. We used historical data from southern California to identify patterns of avian electrocution by voltage, month, and year to identify species most often killed by electrocution in our study area and to develop a predictive model that compared poles where an avian electrocution was known to have occurred (electrocution poles) with poles where no known electrocution occurred (comparison poles). We chose variables that could be quantified by personnel with little training in ornithology or electric systems. Electrocutions were more common at distribution voltages (≤33 kV) and during breeding seasons and were more commonly reported after a retrofitting program began. Red‐tailed Hawks (Buteo jamaicensis) (n = 265) and American Crows (Corvus brachyrhynchos) (n = 258) were the most commonly electrocuted species. In the predictive model, 4 of 14 candidate variables were required to distinguish electrocution poles from comparison poles: number of jumpers (short wires connecting energized equipment), number of primary conductors, presence of grounding, and presence of unforested unpaved areas as the dominant nearby land cover. When tested against a sample of poles not used to build the model, our model distributed poles relatively normally across electrocution‐risk values and identified the average risk as higher for electrocution poles relative to comparison poles. Our model can be used to reduce avian electrocutions through proactive identification and targeting of high‐risk poles for retrofitting. Modelo Predictivo del Riesgo de Electrocución de Aves en Líneas Eléctricas Elevadas     

Spatiotemporal Patterns and Risk Factors for Lead Exposure in Endangered California Condors during 15 Years of Reintroduction

Large‐scale poisoning events are common to scavenging bird species that forage communally, many of which are in decline. To reduce the threat of poisoning and compensate for other persistent threats, management, including supplemental feeding, is ongoing for many reintroduced and endangered vulture populations. Through a longitudinal study of lead exposure in California condors (Gymnogyps californianus), we illustrate the conservation challenges inherent in reintroduction of an endangered species to the wild when pervasive threats have not been eliminated. We evaluated population‐wide patterns in blood lead levels from 1997 to 2011 and assessed a broad range of putative demographic, behavioral, and environmental risk factors for elevated lead exposure among reintroduced California condors in California (United States). We also assessed the effectiveness of lead ammunition regulations within the condor's range in California by comparing condor blood lead levels before and after implementation of the regulations. Lead exposure was a pervasive threat to California condors despite recent regulations limiting lead ammunition use. In addition, condor lead levels significantly increased as age and independence from intensive management increased, including increasing time spent away from managed release sites, and decreasing reliance on food provisions. Greater independence among an increasing number of reintroduced condors has therefore elevated the population's risk of lead exposure and limited the effectiveness of lead reduction efforts to date. Our findings highlight the challenges of restoring endangered vulture populations as they mature and become less reliant on management actions necessary to compensate for persistent threats. Patrones Espaciotemporales y Factores de Riesgo por Exposición a Plomo en Cóndores de California Durante 15 Años de Reintroducción