A comparison of two techniques for studying sediment desorption kinetics of hydrophobic pollutants

A comparison of two techniques (gaseous purge and vial desorption) for studying the kinetics of desorption of hydrophobic pollutants from natural sediments was conducted using identical, pre-equilibrated pollutant-sediment suspensions. Desorption profiles for the two techniques [for Lindane, Aldrin, 2,2'-dichlorobiphenyl (2,2'-DCB), 4,4'-dichlorobiphenyl (4,4'-DCB), and 2,2',6,6'-tetrachlorobiphenyl (TCB)] were then compared, based on the distribution of pollutant mass between the labile (fast) and non-labile (slow) desorption phases and the release rate constants for each phase of release. The vial desorption technique shows many practical advantages over the gaseous purge technique, including its more realistic mixing conditions, the use of an independent sample for each data point (as opposed to a calculation of a cumulative mass purged at each time point), the fact that the vials constitute a closed system and are therefore less subject to ambient contamination, and the relatively low demands of time and money for the vial technique. No consistent trends in labile rate constants or in pollutant distribution between the labile and non-labile phase were observed between the two techniques. A comparison of kinetic parameters shows much faster non-labile rate constants for the gaseous purge technique, attributed to the violent, continuous agitation employed, which likely disrupted sediment aggregates and oxidized the natural organic matter associated with the sediment. Non-labile rate constants have implications for the long-term fate of compounds adsorbed to repetitively disturbed sediments. This study suggests that the traditionally less popular vial desorption technique may yield more realistic non-labile desorption rate constants.     

Bioremediation of kerosene I: A case study in liquid media

The ability of different local isolates in addition to some isolates from Germany to degrade kerosene in liquid medium was studied. The results showed that the percent of kerosene degradation varied among the different organisms and that 59–94% of kerosene was degraded after 21 d. Two local isolates (Pseudomonas sp. AP and Pseudomonas sp. CK) and one German isolate (Gordonia sp. DM) were selected for this study. The addition of wheat bran, as co-substrate, stimulated the kerosene degradation by the two local strains, while glucose inhibited the degradation rate using the three organisms with different rates. Ammonium nitrate and urea was the best nitrogen sources. The use of superphosphate (as phosphorus source) in the presence of urea stimulates the degradation rate. It was also observed that the addition of 1% surfactants, like Triton X-100, Igepal, Tergitol, or Tween 20 and 80 enhanced the kerosene degradation. The degradation percent lied between 94% and 98%. The ability of the tested organisms to degrade kerosene concentration from 2% to 8% was evaluated. It was found that the three organisms degraded about 65–85% from 8% kerosene after 21 d. The use of rice straw-immobilized cells reduced the time of degradation and enhanced the degradation ability of the organisms. The sodium dodecyl sulphate-polyacrylamide gel electrophoresis revealed the presence of a common protein band when the tested organisms were grown on kerosene.     

Seasonal variations of hydrophobic organic contaminant concentrations in the water-column of the Seine Estuary and their transfer to a planktonic species Eurytemora affinis (Calanoïda, copepoda). Part 1: PCBs and PAHs

Hydrophobic organic contaminants (HOC) (i.e. PAHs and PCBs) were measured in the water column and in Eurytemora affinis samples from the Seine Estuary collected from November 2002 to February 2005. Results showed seasonal variations of both total PCB and PAH levels in the suspended particulate matter (SPM) and in the copepods with maximum levels during winter times. PAH and PCB concentrations in the SPM ranged from 499 to 5819ngg(-1) and from 58 to 463ngg(-1), respectively. Phenanthrene, pyrene and benzo[b+j+k]fluoranthene (B[b+j+k]F) were the predominant PAH compounds in the water column, while CB 101, 118, 153 and 138 were the most abundant PCB congeners. PCBs and PAHs bioaccumulated by E. affinis (EA) varied between 383 and 1785ngg(-1) and 165-3866ngg(-1). CB101, 153, 138 and B[b+j+k] were, respectively, the major compounds of PCB and PAH fingerprints in EA. Thereby, the copepods could reach high accumulation factor (ACF) (91000 for PCBs and 17000 for PAHs). The principal component analyses of contaminant concentrations and environmental parameter datasets distinguished two groups of copepods. The winter time cluster, with high percentage of adult copepods, which bioaccumulated the highest PCB and PAH body-burdens, and the second cluster with juveniles showing the lowest HOC concentrations. Thus, PAH and PCB concentrations in EA exhibited significant correlations with the percentage of adults making up the samples.     

Serum profiles of PCDDs and PCDFs, in individuals near the Escambia Wood Treating Company Superfund site in Pensacola, FL

The Escambia Wood Treating Company (ETC) Superfund site, Pensacola, FL, is contaminated with polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/F), benzo(a)pyrene, lead and arsenic from pentachlorophenol (PCP), creosote, and other compounds used to treat utility poles and foundation pilings. Although ETC's operations ceased in 1982, soils in the areas surrounding the facility continue to exhibit elevated levels of contaminants attributable to ETC operations. In July 2000, individuals who may have been affected by contamination from the ETC site, including current and former residents and former workers and their household members were invited to participate in a study, which included a health and exposure history and routine blood analysis. We also conducted a toxicological health evaluation of a subset of these eligible workers/residents by analyzing serum levels of 17 PCDD/F congeners. Members of the ETC cohort exhibited elevated serum PCDD/F relative to the general population, and congener profiles in members of the cohort reflected patterns commonly observed in persons exposed to PCP. Hypertension prevalence in the cohort was found to correlate with PCDD/F levels, although no other significant relationships were identified with monitored health indices.     

Estrogenic activity removal of 17beta-estradiol by ozonation and identification of by-products

This work investigated the degradation of a natural estrogen (17beta-estradiol) and the removal of estrogenic activity by the ozonation process in three different pHs (3, 7 and 11). A recombinant yeast assay (YES assay) was employed to determine estrogenic activity of the ozonized samples and of the by-products formed during the ozonation. Ozonation was very efficient for the removal of 17beta-estradiol in aqueous solutions. High removals (>99%) were achieved with low ozone dosages in the three different pHs. Several by-products were formed during the ozonation of 17beta-estradiol. However, only a few compounds could be identified and confirmed. Different by-products are formed at different pHs, which is probably due to different chemical pathways and different oxidants (O(3) and OH radical). The by-products formed at pH 11 were 10epsilon-17beta-dihydroxy-1, 4-estradieno-3-one (DEO) and 2-hydroxyestradiol, which were not formed in pH 3. Only testosterone could be observed in pH 3, whereas at pH 7 all three by-products were found. At pH 7 and 11 the applied ozone dosages were not enough to remove all the estrogenicity from samples, even though the 17beta-estradiol residual concentration for these two pHs was lower than at pH 3. Higher estrogenicity was detected at pH 11. An explanation to this fact may be that oxidation via OH radical forms more by-products with estrogenic activity. Probably, the formation of 2-hydroxyestradiol at pHs 7 and 11 is contributing to the residual estrogenicity of samples ozonized at these pHs. In this work, complete removal of estrogenic activity was only obtained at pH 3.     

Bioremediation process on Brazil shoreline

GOAL, SCOPE AND BACKGROUND: Bioremediation technique can be considered a promising alternative to clean oil spills using microbial processes to reduce the concentration and/or the toxicity of pollutants. To understand the importance of this work we must know that there is only little research performed to date using bioremediation techniques to clean oil spills in tropical countries. So, the main objective of this work is to analyze the behavior of a laboratory's bioremediation test using nutrients on coastal sediments. METHODS: The bioremediation process is followed through geochemical analysis during the tests. This organic material is analyzed by medium pressure liquid chromatography (MPLC), gas chromatography/flame ionization detection (GC/FID) and gas chromatography/ mass spectrometry. By microbial counting, the number of total bacteria and degrading bacteria is determined during the experiments, in order to confirm the effectiveness of the bioremediation process. The seawater obtained throughout the bioremediation process is analyzed for nutrients grade (phosphate and ammonium ions) and also for its toxicity (Microtox tests) due the presence of hydrocarbons and fertilizer. RESULTS: The results from the geochemical analyses of the oil show a relative decrease in the saturated hydrocarbon fraction that is compensated by a relative enrichment on polar compounds. It's confirmed by the fingerprint evaluation where it is possible to see a complete reduction of the normal alkanes followed by isoprenoids. Seawater analysis done by toxicity and nutrients analysis, such as microbial counting (total and degrading bacteria), confirm the fertilizer effectiveness during the bioremediation process. DISCUSSION: Results from simulating test using NPK, a low-price plant fertilizer, suggest that it's able to stimulate the degradation process. Results from medium pressure liquid chromatography (MPLC), done at two different depths (surface and subsurface), show different behavior during the biodegradation process where the later is seen to be more susceptible to microbial attack. Data from bioremediation unit shows a bigger reduction of the saturated fraction, followed by some smaller reduction of aromatic fractions, compensated by a relative increase from polar compounds (NSO). n-C17/pristane, n-C18/ fitane and pristane/fitane rates show constant values for the unity control, different from bioremediation samples which have a significant reduction, especially on subsurface areas, where a strong fall in the rates, seen to be reduced to zero over twenty days, had occurred during the first ten days. However, sample surfaces are reduced to zero in thirty days of experiments, proving that biodegradation is better on subsurfaces. Gaseous chromatography/mass spectrometry (CG/MS) analysis shows constant values to cyclic biomarker rates and aromatic compounds, suggesting that the biodegradation process is not strong enough to reduce these composites. Microbial analysis shows a reduction on heterotrophic (total bacteria) number from control unit, probably because the bacteria uses the spill oil like carbon source and energy. However, the number increases on bioremediation unit, because it uses NPK like a biostimulator. The hydrocarbonoclastic number isn't enough on the first moment, but it's detected after 30 days and quantified in all units, showing big values especially in bioremediation. Toxicity tests confirm that NPK fertilizer does not intoxicate the shoreline during the application of the bioremediation technique. Some nutrient concentration shows high values of ammonium and phosphate per bioremediation unit, reducing by the end of the experiment. CONCLUSIONS: Results reached the goal, finding a proper nutrient (NPK fertilizer) to stimulate the biodegradation process, growing bacteria responsible for reducing impact-contaminated coast ambient by oil spills. Chemical analysis of oil shows a reduction in the saturated fraction with a relative enrichment in polar composites (NSO) and the aromatic fraction from oil remaining constant. Subsurface samples show more biodegradation than surface samples, probably because the first one has higher humidity. Linear alcanes are more biodegraded than isoprenoids, confirming the biodegradation susceptibility order. Saturated cyclic biomarkers and aromatic compounds show constant behavior maybe because the nutrients or time was not enough for microorganismic attack. Fertilizer does not demonstrate any toxic effects in local biota so that it does not compromise the technique applicability and the environment is not saturated by nutrients during the simulation, especially since the coastal environment is an open system affected daily by tides. Therefore, bioremediation tests can be classified as moderate, reaching level 5 in the classification scale by Peters & Moldowan (1993). RECOMMENDATIONS AND PERSPECTIVES: The use of marine environment by the petroleum industry on exploration, production and transportation operation, transform this oil to become the most important pollutant in the oceans. Bioremediation is an important technique used to clean spilled oil impacting on shorelines, accelerating the biodegradation process by using fertilizer growing the microorganisms responsible for decontaminating the environment. We recommend confirming the efficiency of NPK nutrient used on bioremediation simulating experiments on beaches, while monitoring the chemical changes long-term. NPK fertilizer can be used to stimulate the biodegradation process on shoreline impacted by spilled oil.     

Relation of waste generation and composition to socio-economic factors: a case study

To develop an effective waste management strategy for a given region, it is important to know the amount of waste generated and the composition of the waste stream. Past research has shown that the amount of waste generated is proportional to the population and the average mean living standards or the average income of the people. In addition, other factors may affect the amount and composition of waste. These are climate, living habits, level of education, religious and cultural beliefs, and social and public attitudes. This paper presents the findings of a study carried out in a suburban municipal area in Sri Lanka to determine the solid waste generation rate and waste composition based on field surveys and to determine the related socio-economic factors. A database was developed that included information on the quantity and composition of waste generated in a sample of households in the study area over a time period. The collected data was analysed to relate waste generation and composition data to various socio-economic factors. Over 400 sample households were selected for the study using a stratified random sampling methodology based on municipal wards and property values. A technique that considers both the number of households in a particular income group (property value range) and the standard deviation of property values within a given income group was used to determine the appropriate sample size for each municipal ward. Through category and regression analyses, the quantities of waste and waste composition were related to several socio-economic factors. The paper describes the basis for the sample selection, the methodology adopted for data collection, the socio-economic parameters used for the analysis, and the relationships developed from the analysis.     

Desorption of arsenic from drinking water distribution system solids

Previous work has shown that arsenic can accumulate in drinking water distribution system (DWDS) solids (Lytle et~al., 2004) when arsenic is present in the water. The release of arsenic back into the water through particulate transport and/or chemical release (e.g. desorption, dissolution) could result in elevated arsenic levels at the consumers' tap. The primary objective of this work was to examine the impact of pH and orthophosphate on the chemical release (i.e. desorption) of arsenic from nine DWDS solids collected from utilities located in the Midwest. Arsenic release comparisons were based on the examination of arsenic and other water quality parameters in leach water after contact with the solids over the course of 168~hours. Results showed that arsenic was released from solids and suggested that arsenic release was a result of desorption rather than dissolution. Arsenic release generally increased with increasing initial arsenic concentration in the solid and increasing pH levels (in the test range of 7 to 9). Finally, orthophosphate (3 and 5 mg PO₄/L) increased arsenic release at all pH values examined. Based on the study results, utilities with measurable levels of arsenic present in their water should be aware that some water quality changes can cause arsenic release in the DWDS potentially resulting in elevated levels at the consumer's tap.     

Deficit analysis: service capacity assessment and planning in developing countries – case study in the Philippines

Current demand analysis methods do not formally cover the case of chronic deficits in quantity or quality of water and sanitation services. These services include drinking water supply (DWS), wastewater and sewage treatment (WST), and municipal solid waste management (MSW). Formal analysis of this case would, at minimum, define the deficit state and evaluate appropriate options for reducing it. This paper proposes for a formal analytical model for municipal sanitation systems (MSS) that operate with deficits in at least one of the constituent services of DWS, WST, or MSW. The model introduces definitions and notation for describing the deficit state for conducting demand analysis on municipal sanitation systems. This model of demand analysis for systems with chronic deficits will hereinafter be referred to as deficit analysis. A case study for Bacoor, Philippines is presented as an example.     

Testing the use of juvenile Salmo trutta L. as biomonitors of heavy metal pollution in freshwater

Individual specimens of Salmo trutta were captured, from four sampling sites in Galician rivers (NW Spain) affected by different types of contamination: diffuse urban waste, run-off from an unrestored dump at a copper mine and waste from a fish farm. The ages of the captured trouts were established and only those belonging to the 1+ age class were selected for study. The liver and kidney were removed from each fish and analysed to determine the tissue concentrations of Cu, Fe and Zn. The results obtained showed that: (i) the use of 1+ individuals allowed differentiation of contamination scenarios on the basis of the tissue concentrations of metal; (ii) the use of 1+ individuals allowed standardization of the time of exposure, which was sufficiently long for differential uptake to have taken place; (iii) liver tissue provided the best results as, less effort was required than for processing kidney tissue, and significant differences between sampling sites were detected because the intrapopulational variability in metal levels was lower than for kidney, and (iv) the levels of elements detected were not affected by basal tissue concentrations or residual concentrations due to past contamination, which older trouts may have been exposed to. In addition, the use of 1+ trout may provide better results in annual environmental sampling surveys.