Characterization of tannery effluent wastewater by proton-induced X-ray emission (PIXE) analysis to investigate their role in water pollution

Introduction  

Over the last few decades, the chromium-based tanning industry has shown rapid growth in Pakistan. However, the rules and regulations promulgated by the government are not strictly followed for processing the effluent discharge from the tanneries. Consequently, tannery effluents have become a great source of water pollution in surrounding areas.     

Monitoring trace elements generated by automobiles: air pollutants with possible health impacts

Major transformations in the environmental composition are principally attributable to the combustion of fuels by automobiles. Motorized gasoline-powered two-stroke auto-rickshaws (TSA) and compressed natural gas (CNG)-powered four-stroke auto-rickshaws (FSA) are potential source of air pollution in south Asia and produce toxic amount of particulate matter (PM) to the environment. In this study, we attempted to characterize elemental pollutants from the PM of TSA and FSA using proton-induced X-ray emission (PIXE) analysis. The observations of the existing investigation recognized significant increase in Al (P?<?0.05), P (P?<?0.01), and Zn (P?<?0.01) from the PM samples of FSA. In addition, the concentrations of Cu, Fe, K, Mg, Na and S were also observed exceeding the recommended National Institute for Environmental Studies limits. On the contrary, increased concentration of Sr and V were observed in the PM samples from TSA. It is generally believed that FSA generates smaller amount of PM but data obtained from FSA are clearly describing that emissions from FSA comprised potentially more toxic substances than TSA. The current research is specific to metropolitan population and has evidently revealed an inconsistent burden of exposure to air pollutants engendered by FSA in urban communities, which could lead to the disruption of several biological activities and may cause severe damage to entire ecological system.     

Study of contaminant transport at an open-tipping waste disposal site

Field and laboratory studies were conducted to estimate concentration of potential contaminants from landfill in the underlying groundwater, leachate, and surface water. Samples collected in the vicinity of the landfill were analyzed for physiochemical parameters, organic contaminants, and toxic heavy metals. Water quality results obtained were compared from published data and reports. The results indicate serious groundwater and surface water contamination in and around the waste disposal site. Analysis of the organic samples revealed that the site contains polychlorinated biphenyls and other organo-chlorine chemicals, principally chloro-benzenes. Although the amount of PCB concentration discovered was not extreme, their presence indicates a potentially serious environmental threat. Elevated concentrations of lead, copper, nickel, manganese, cadmium, and cobalt at the downgradient indicate that the contamination plume migrated further from the site, and the distribution of metals and metals containing wastes in the site is nonhomogeneous. These results clearly indicate that materials are poorly contained and are at risk of entering the environment. Therefore, full characterization of the dump contents and the integrity of the site are necessary to evaluate the scope of the problem and to identify suitable remediation options.     

A multi-residue method for the analysis of organophosphorus residues in cooked and polished rice using accelerated solvent extraction and dispersive-solid phase extraction (D-SPE) technique and uncertainty measurement

Quick, simple and efficient multi-residue analytical methods were developed and validated for the determination of organophosphorous insecticides from polished and cooked rice. Polished rice was extracted using a simple, automated technique namely accelerated solvent extraction (ASE) using dichloromethane as the extraction solvent. Cooked rice was extracted with acetone and cleaned up using dispersive-solid phase extraction (D-SPE) technique. The single step extraction method adopted for polished rice using accelerated solvent extractor provided satisfactory recovery for eight organophosphorus pesticides (OPPs) which ranged from 85.5–116.7%; 90.0–110.3% and 93.5–118.8% at 1, 5 and 10 limit of quantification (LOQ) levels, respectively. The recovery of cooked rice was in the range of 74–124%; from 75–100% and from 73–87% for 1, 5 and 10 level of fortification, respectively. The total uncertainty was evaluated, taking four main independent sources viz., weighing, purity of the standard, GC calibration curve and repeatability under consideration. The expanded uncertainty was found to be in the range of 5–20%.     

Degradation Kinetics of Biofilter Media Treating Reduced Sulfur Odors and VOCs

ABSTRACT

A lab-scale study was conducted to determine the rate and extent of decomposition of three biofilter media materials—compost, hog fuel, and a mixture of the two in 1:1 ratio—used in biofiltration applied to removal of reduced sulfur odorous compounds from pulp mill air emissions. The rate of carbon mineralization, as a measure of biofilter media degradation, was determined by monitoring respiratory CO₂ evolution and measuring the changes in carbon and nitrogen fractions of the biofilter materials over a period of 127 days. Both ambient air and air containing reduced sulfur (RS) compounds were used, and the results were compared. After 127 days of incubation with ambient air, about 17% of the media carbon was evolved as CO₂ from compost as compared to 6 and 12% from hog fuel and the mixture, respectively. The decomposition showed sequential breakdown of carbon moieties, and three distinct stages were observed for each of the biofilter media. First-order rate kinetics were used to describe the decomposition stages. Decomposition rates in the initial stages were at least twice those of the following stages. Carbon mineralization showed close dependence on the C/N ratio of the biofilter material. Media decomposition was enhanced in the presence of RS gases as a result of increased bioactivity by sulfur-oxidizing bacteria and other microorganisms, thus reducing the media half-life by more than 50%. At higher concentrations of RS gases, the CO₂ evolution rates were proportionally lower than those at the low concentrations because of the limited acid buffering capacity of the biofilter materials.     

Inhalation exposure to volatile organic compounds in the printing industry

ABSTRACT

This study reports on the occupational inhalation exposure to VOCs of workers in the Kuwaiti printing industry. Using the evacuated canister methodology, we targeted 72 VOCs in three printeries and compared the concentrations to previous reports and relevant occupational exposure levels (OELs). We found that recent efforts in the printing industry to reduce VOC usage had been successful, as concentrations of key hazardous VOCs were substantially lower than anticipated. On the other hand, nearly all target VOCs were found. Non-production areas were sampled along with the offset printing areas, another strength of this study, and revealed exposures to hazardous VOCs among administers and digital printer and CTP operators. Exposure to ototoxic VOCs amounted to 1–3% of the OEL, consisting mostly of ethylbenzene, which was likely in use in two of the study printeries. Exposure to carcinogenic or probably carcinogenic VOCs was 15–20% of the OEL at four locations across the three printeries, consisting mostly of vinyl chloride and benzyl chloride. Vinyl chloride VOC was partially sourced from outdoors, but was also likely used inside the study printeries. Interestingly, concentrations of vinyl chloride were similar in most sampling locations to that of CFC-114, a CFC banned by the Montreal Protocol and not commonly used as a refrigerant. This unexpected finding suggests further study is warranted to identify the use of these VOCs in printeries. Exposure to hazardous VOCs up to nearly 50% of the OEL, consisting largely of bromoform and vinyl chloride. Bromoform was found in all the study printeries, sourced partially from outdoor air. The higher concentrations found inside the study printeries likely resulted from the use of the desalinated water for washing. This finding raises of emissions from sources other than blanket washes, and inks, etc. adding to the total VOC load in printery indoor air.

Implications: Results from this study indicate that efforts to reduce worker exposure to VOCs particularly dangerous to human health in recent years have been successful, but there is still much to be done to protect workers. Exposures to ototoxic and carcinogenic VOCs were identified, among both production and non-production workers. Unexpected findings included the apparent use in printing activities of the carcinogen vinyl chloride and CFC-114, banned under the Montreal Protocol. Observed lapses in safety procedures included failure to utilize ventilation systems and closing doors between work areas, indicating management and worker education should remain a priority.     

Improvement of Physico-Mechanical Properties of Photo-Cured Chitosan Films with Ethylene Glycol Dimethacrylate and (2-Hydroxyethyl) Methacrylate

Chitosan, a natural polymer, was prepared by deacetylation of chitin which was obtained from dried prawn shell and was characterized. Thin chitosan film of chitosan was prepared by casting method from 0.2 % chitosan in 2 % acetic acid solution. Five formulations were developed with ethylene glycol dimethacrylate and (2-hydroxyethyl) methacrylate along with photo-initiator, Darocur-1664 (4 %). The chitosan film was soaked in the formulations at different soaking times and irradiated under UV-radiation at different intensities for the improvement of its physical and mechanical properties. The cured chitosan films were then subjected to various mechano-chemical tests like tensile strength, elongation at break, polymer loading, water absorption and gel content. The formulation containing 30 % ethylene glycol dimethacrylate and 66 % (2-hydroxyethyl) methacrylate showed the best performance at the 30th UV pass of UV-radiation for 3 min soaking time.     

Evaluation of non-enteric sources of non-methane volatile organic compound (NMVOC) emissions from dairies

Dairies are believed to be a major source of volatile organic compounds (VOC) in Central California, but few studies have characterized VOC emissions from these facilities. In this work, samples were collected from six sources of VOCs (Silage, Total Mixed Rations, Lagoons, Flushing Lanes, Open Lots and Bedding) at six dairies in Central California during 2006–2007 using emission isolation flux chambers and polished stainless steel canisters. Samples were analyzed by gas chromatography/mass spectrometry and gas chromatography/flame ionization detection. Forty-eight VOCs were identified and quantified in the samples, including alcohols, carbonyls, alkanes and aromatics. Silage and Total Mixed Rations are the dominant sources of VOCs tested, with ethanol as the major VOC present. Emissions from the remaining sources are two to three orders of magnitude smaller, with carbonyls and aromatics as the main components. The data suggest that animal feed rather than animal waste are the main source of non-enteric VOC emissions from dairies.     

n-Hexane Biodegradation in Trickle Bed Air Biofilters

While hydrophilic compounds are degraded easily in Trickling bed air biofilters (TBABs), hydrophobic compounds are retarded until biological cultures produce a sufficient RNA or enzyme/protein to utilize this compound. Hydrophobic compounds are not readily bio-available which makes them reluctant to biodegradation as mass transfer between the gas and liquid phases is a rate limiting step. To enhance the destruction of hydrophobic compounds in TBABs, the utilization of surfactant was introduced to increase the solubility which helps overcoming the rate limiting step. The surfactant was used as well to limit the growth of excess biomass ensuring smooth flow through the biofilter bed and preventing short circuits. Two different non-ionic non-toxic surfactants were used in this study: Triton X-100 and Tomadol® 25-7. Two lab-scale controlled TBABs were operated for investigating the performance difference for n-Hexane as an example of hydrophobic volatile organic compound (VOC) with and without the addition of surfactant. Operating conditions in both TBABs were as follows: nutrient feed rate (2L/day), air flowrate (1.4L/min), bed depth (60cm), empty bed retention time (120s), bed material (diatomaceous earth pellets) and room-temperature. The inlet concentration was changed from 50 to 100ppmv. Acclimation period, removal profile along biofilter depth, nitrogen consumption, and CO₂ production were compared under continuous loading operation condition. The optimum concentration of surfactant in the nutrient feed was determined by a batch experiment. The effect of different surfactant concentrations on VOC water solubility with time was studied by considering different VOC concentration sets within the TBAB loading rate range.     

Transient behavior of heavy metals in soils during electrokinetic remediation

This paper presents a systematic bench-scale laboratory study performed to assess the transient behavior of chromium, nickel, and cadmium in different soils during electrokinetic remediation. A series of laboratory electrokinetic experiments was conducted using two different clayey soils, kaolin and glacial till. For each type of soil, four electrokinetic experiments with 1, 2, 4, and 10 d of treatment time were performed. In all tests, the contaminants were Cr(VI), Ni(II), and Cd(II) combined in the soil. A geochemical assessment was performed using the geochemical model MINEQL(+) to determine the partitioning of the heavy metals in soils as precipitated, adsorbed, and aqueous forms. Results showed that in kaolin, the extent of Ni(II) and Cd(II) migration towards the cathode increased as the treatment time increased. Unlike kaolin, in glacial till treatment time had no effect on nickel and cadmium migration because of its high buffering capacity. In both kaolin and glacial till, the extent of Cr(VI) migration towards the anode increased as the treatment time increased. However, Cr(VI) migration was higher in glacial till as compared to kaolin because of the high pH conditions that existed in glacial till. In all tests, some Cr(VI) was reduced to Cr(III), and the Cr(VI) reduction rate to Cr(III) as well as the Cr(III) migration were significantly affected by the treatment time. Overall, this study showed that the electroosmotic flow as well as the direction and extent of contaminant migration and removal depend on the polarity of the contaminant, the type of soil, and the treatment duration.