Comparison of in-house-developed ELISA with HPLC techniques for the analysis of atrazine residues

In-house developed ELISA was standardized to monitor atrazine residues in different environmental samples. The standard curve was linear, indicating an increase in log concentration with decrease in absorbance (%B/B(0)=1.075-0.042 Log C; r= -0.966). The middle of the test was at 75 ng/L and the lowest detection limit at 4 ng/L. ELISA significantly correlated with the high performance liquid chromatography (HPLC) (r=0.990). Internal validation showed good accuracy and precision. Maximum atrazine residues were present in Jehlum River water/sediments and maize/sugarcane plant roots. Most of the food samples were found to be contaminated. ELISA required less clean-up steps than HPLC, but showed matrix effect in soil/colored extracts.     

Implementation of a windblown dust parameterization into MODELS-3/CMAQ: Application to episodic PM events in the US/Mexico border

Windblown dust is known to impede visibility, deteriorate air quality and modify the radiation budget. Arid and semiarid areas with unpaved and unvegetated land cover are particularly prone to windblown dust, which is often attributed to high particulate matter (PM) pollution in such areas. Yet, windblown dust is poorly represented in existing regulatory air quality models. In a study by the authors on modeling episodic high PM events along the US/Mexico border using the state-of-the-art CMAQ/MM5/SMOKE air quality modeling system [Choi, Y.-J., Hyde, P., Fernando, H.J.S., 2006. Modeling of episodic particulate matter events using a 3D air quality model with fine grid: applications to a pair of cities in the US/Mexico border. Atmospheric Environment 40, 5181–5201], some of the observed PM₁₀ NAAQS exceedances were inferred as due to windblown dust, but the modeling system was incapable of dealing with time-dependent episodic dust entrainment during high wind periods. In this paper, a time-dependent entrainment parameterization for windblown dust is implemented in the CMAQ/MM5/SMOKE modeling system with the hope of improving PM predictions. An approach for realizing windblown dust emission flux for each grid cell over the study domain on an hourly basis, which accounts for the influence of factors such as soil moisture content, atmospheric stability and wind speed, is presented in detail. Comparison of model predictions with observational data taken at a pair of US/Mexico border towns shows a clear improvement of model performance upon implementation of the dust emission flux parameterization.     

Trends in snowpack chemistry and comparison to National Atmospheric Deposition Program results for the Rocky Mountains, US, 1993–2004

Seasonal snowpack chemistry data from the Rocky Mountain region of the US was examined to identify long-term trends in concentration and chemical deposition in snow and in snow-water equivalent. For the period 1993–2004, comparisons of trends were made between 54 Rocky Mountain Snowpack sites and 16 National Atmospheric Deposition Program wetfall sites located nearby in the region. The region was divided into three subregions: Northern, Central, and Southern. A non-parametric correlation method known as the Regional Kendall Test was used. This technique collectively computed the slope, direction, and probability of trend for several sites at once in each of the Northern, Central, and Southern Rockies subregions. Seasonal Kendall tests were used to evaluate trends at individual sites.Significant trends occurred during the period in wetfall and snowpack concentrations and deposition, and in precipitation. For the comparison, trends in concentrations of ammonium, nitrate, and sulfate for the two networks were in fair agreement. In several cases, increases in ammonium and nitrate concentrations, and decreases in sulfate concentrations for both wetfall and snowpack were consistent in the three subregions. However, deposition patterns between wetfall and snowpack more often were opposite, particularly for ammonium and nitrate. Decreases in ammonium and nitrate deposition in wetfall in the central and southern rockies subregions mostly were moderately significant (p<0.11) in constrast to highly significant increases in snowpack (p<0.02). These opposite trends likely are explained by different rates of declining precipitation during the recent drought (1999–2004) and increasing concentration. Furthermore, dry deposition was an important factor in total deposition of nitrogen in the region. Sulfate deposition decreased with moderate to high significance in all three subregions in both wetfall and snowpack. Precipitation trends consistently were downward and significant for wetfall, snowpack, and snow-telemetry data for the central and southern rockies subregions (p<0.03), while no trends were noted for the Northern Rockies subregion.     

Characterizing effects of uncertainties in MSW composting process through a coupled fuzzy vertex and factorial-analysis approach

A coupled fuzzy vertex and factorial-analysis approach was developed in this study for systematically characterizing effects of uncertainties in a municipal solid waste composting process. A comprehensive composting process model was also embedded into the system framework and used to address substrate decomposition and biomass growth, as well as the interactions between moisture contents, temperatures, and oxygen concentrations. The applicability of the proposed method was verified through a custom-made pilot-scale composting system. Results from fuzzy simulation indicated that the fuzzy vertex method could effectively communicate implicit knowledge into dynamic simulations and thus provide valuable information for enhancing composting process control under uncertainty. The factorial analysis was effective in quantifying the proportion to which the uncertainty of each single or interactive effect of model parameters contributes to the overall uncertainty of the system outcomes. Thus, sensitive parameters that may lead to errors or unreasonable predictions can be determined. The proposed study system could not only be used in characterizing combined effects of uncertainties for composting processes, but was also applicable to many other environmental modelling systems.     

Mechanical properties of concrete containing a high volume of tire-rubber particles

Due to the increasingly serious environmental problems presented by waste tires, the feasibility of using elastic and flexible tire-rubber particles as aggregate in concrete is investigated in this study. Tire-rubber particles composed of tire chips, crumb rubber, and a combination of tire chips and crumb rubber, were used to replace mineral aggregates in concrete. These particles were used to replace 12.5%, 25%, 37.5%, and 50% of the total mineral aggregate's volume in concrete. Cylindrical shape concrete specimens 15 cm in diameter and 30 cm in height were fabricated and cured. The fresh rubberized concrete exhibited lower unit weight and acceptable workability compared to plain concrete. The results of a uniaxial compressive strain control test conducted on hardened concrete specimens indicate large reductions in the strength and tangential modulus of elasticity. A significant decrease in the brittle behavior of concrete with increasing rubber content is also demonstrated using nonlinearity indices. The maximum toughness index, indicating the post failure strength of concrete, occurs in concretes with 25% rubber content. Unlike plain concrete, the failure state in rubberized concrete occurs gently and uniformly, and does not cause any separation in the specimen. Crack width and its propagation velocity in rubberized concrete are lower than those of plain concrete. Ultrasonic analysis reveals large reductions in the ultrasonic modulus and high sound absorption for tire-rubber concrete.     

Soils, climate change and the OECD

Some concepts of sustainability applied to soils are given in relation to the Organisation for Economic Co-operation and Development (OECD) Co-operative Research Programme 'Biological Resource Management for Sustainable Agricultural Systems'. The application of these concepts to climate change will be discussed in relation to seven high-profile papers published over the past 12 months. It is argued that multi-disciplinary (including social science) approaches are needed to address the issues. There is also a brief discussion on biomass energy in terms of soil sustainability and climate change.     

The removal of lignin and phenol from paper mill effluents by electrocoagulation

This study aims to investigate the treatment of paper mill effluents using electrocoagulation. Removal of lignin, phenol, chemical oxygen demand (COD) and biological oxygen demand (BOD) from paper mill effluents was investigated at various current intensities by using different electrodes (Al and Fe) and at various electrolysis times (1.0, 2.5, 5.0 and 7.5min). It was observed that the experiments carried out at 12V, an electrolysis time of 2min and a current intensity of 77.13mA were sufficient for the removal of these pollutants with each electrode. The removal capacities of the process using an Al electrode were 80% of lignin, 98% of phenol, 70% of BOD, and 75% of COD after 7.5min. Using an Fe electrode the removal capacities were 92%, 93%, 80% and 55%, respectively. In addition, it was found that removal of lignin, phenol, BOD and COD increased with increasing current intensity. In the experiments carried out at different current intensities, higher removal can be explained through a decrease in intra-resistance of solution and consequently an increase at the transfer speed of organic species to electrodes. It was also found that Al electrode performs higher efficiency than Fe electrode except for COD removal. However, the time required for removal of BOD was more than that of COD. The results suggest that electrocoagulation could be considered as an effective alternative to paper mill effluents treatment.     

Invasion of Pinus halepensis Mill. following a wildfire in an Argentine grassland nature reserve

The Ernesto Tornquist nature reserve is a relict of native Pampas vegetation in Argentina. Alien trees were introduced to the reserve in the 1950s, mainly to "improve" the natural landscape, resulting in the arrival of a totally new life form. In 1987, a fire affected an area planted with Pinus halepensis resulting in its massive expansion. In 1999, we removed trees from 17 circular plots of 10 m diameter placed systematically within the area that was colonized after the fire. Trunks were cut 20 cm from the ground and growth rings were counted. We studied the age structure of the population in order to reconstruct the colonizing events after the fire. We found that recruitment occurred throughout this period, except in the three years after the disturbance. We suggest that this delay in recruitment might be caused by low seedling survival under water stress conditions due to low rainfall, combined with scarce vegetation cover after fire. This could have been associated with an initial reduction in propagule pressure due to the scarcity of surviving trees in the vicinity and with the fact that fire occurred after the peak of seed release, during an extremely dry summer, probably killing a great number of seeds that were already in the soil. In the following years, recruitment was probably aided by pioneer trees and later by seeds shed from established pines. Alien trees had been allowed to reach maturity due to wildfire prevention and control in the years preceding the fire and the accumulated dry matter resulted in increased fire intensity that reduced the ability of grasses to re-sprout. As a consequence, the invasion window that allowed the expansion of pines remained open for at least 12 years.     

Coupling a 3D patch model and a rockfall module to assess rockfall protection in mountain forests

Many forests in the Alps are acknowledged for protecting objects, such as (rail) roads, against rockfall. However, there is a lack of knowledge on efficient silvicultural strategies and interventions to maintain these forests at optimal protection level. Therefore, assessment tools are required that quantify the rockfall protection effect of forest stands over time, and thereby provide the ability to evaluate the necessity and effect of management interventions. This paper introduces such a tool that consists of a 3D rockfall module embedded in the patch based forest simulator PICUS. The latter is extended for this study with a new regeneration module. In a series of experiments the new combined simulation tool is evaluated with regard to parameter sensitivity, model intercomparison experiments with recently proposed algorithms from the literature, and the ability to respond realistically to different management regimes in rockfall protection forests. Results confirm the potential of the new tool for realistic simulation of rockfall activity in heterogeneous mountain forests, but point at the urgent need to improve the knowledge base on the interaction of understory and rockfall activity. Further work will focus on model validation against empirical rockfall data, and include reduced tree vitality due to damage from boulder collisions as well as the explicit consideration of downed dead wood.     

Non-Fickian dispersion in a single fracture

Solute transport in fractured rocks is of major interest in many applications, from the petroleum industry to ground water management. This work focuses on the dispersion process in a transparent replica of a real single fracture. The fracture exhibits strong changes in heterogeneity, with the first half very heterogeneous and the second half fairly homogeneous. Three models have been used to interpret the tracer experiments: the classical advection-dispersion equation (ADE), the continuous time random walk (CTRW), and the stratified model. The main goals were to test these models and to study possible correlations between fitting parameters and heterogeneities. As expected, the solution derived from the ADE equation appears to be unable to model long-time tailing behavior. On the other hand, the results confirm the CTRW robustness and the coefficient beta seems well correlated to heterogeneities. Finally, the stratified model is also able to describe non-Fickian dispersion. The parameters defined by this model are correlated to the heterogeneities of the fracture.