REGULATING NONPOINT SOURCE POLLUTION IN SURFACE WATERS: A PROPOSAL1

ABSTRACT: Nonpoint sources (NPS) are an important and continuing source of toxic and conventional pollutants to surface waters. The Clean Water Act amendments of 1987 call for the regulation of these sources through the use of Best Management Practices (BMP). However, BMP implementation has generally occurred on a voluntary basis. This paper proposes a regulatory mechanism to control nonpoint source pollution. The regulatory mechanism involves the development of consortia, made up of all parties potentially responsible for NPS pollution, the development of wasteload allocations that coordinate the pollutant contributions from both point and nonpoint sources in a stream segment, and the issuance of permits to consortia to regulate the impacts of NPS pollution and ensure achievement of state or federal Water Quality Criteria and Standards.     

Laboratory evidence of MTBE biodegradation in Borden aquifer material

Mainly due to intrinsic biodegradation, monitored natural attenuation can be an effective and inexpensive remediation strategy at petroleum release sites. However, gasoline additives such as methyl tert-butyl ether (MTBE) can jeopardize this strategy because these compounds often degrade, if at all, at a slower rate than the collectively benzene, toluene, ethylbenzene and the xylene (BTEX) compounds. Investigation of whether a compound degrades under certain conditions, and at what rate, is therefore important to the assessment of the intrinsic remediation potential of aquifers. A natural gradient experiment with dissolved MTBE-containing gasoline in the shallow, aerobic sand aquifer at Canadian Forces Base (CFB) Borden (Ontario, Canada) from 1988 to 1996 suggested that biodegradation was the main cause of attenuation for MTBE within the aquifer. This laboratory study demonstrates biologically catalyzed MTBE degradation in Borden aquifer-like environments, and so supports the idea that attenuation due to biodegradation may have occurred in the natural gradient experiment. In an experiment with batch microcosms of aquifer material, three of the microcosms ultimately degraded MTBE to below detection, although this required more than 189 days (or >300 days in one case). Failure to detect the daughter product tert-butyl alcohol (TBA) in the field and the batch experiments could be because TBA was more readily degradable than MTBE under Borden conditions.     

Modelling radioiodine transport across a capillary fringe

Due to its long radioactive half-life, iodine-129 is considered to be an important radionuclide in the context of underground radioactive waste disposal safety assessment. Iodine speciates as iodide (I-) in reducing conditions and iodate (IO3-) in oxidizing conditions. As iodate is more reactive, it is much less mobile than iodide. Consequently, in considering vertically upward transport within a soil profile, iodine will tend to accumulate at the top of the capillary fringe. In this paper, a model of iodine transport across a capillary fringe is developed by coupling equations for variably saturated flow, oxygen dynamics and rate-limited sorption. Model parameters are obtained by consideration of literature values, calibration on soil column data and other supporting laboratory experiments. The results demonstrate the importance of rate kinetics on the migration and bioavailability of radioiodine in the near-surface environment.     

Useful indicators of urban sustainability: Some methodological issues

This paper considers methodological questions concerning indicators of sustainability, which have arisen in the course of an EPSRC-supported project investigating a systems approach to assessing the sustainability of cities. The project aimed: (a) to develop a methodology, the Reference Sustainability System (RSS), for representing the energy, resource and material flows, on which the environmental sustainability of cities depends; (b) to show how this methodology could contribute to a more systematic assessment of the potential of technological and resource management strategies to enhance urban sustainability. Systems models of the material or resource flows caused by the household demand for paper, energy, water and bottled water have been constructed. The project has highlighted the complexity of assessing the contributions of specific technologies and strategies to enhanced sustainability. Particular issues raised include the relative merits and problems of using externality valuation methods compared to physical indicators, the difficulties of aggregating environmental impacts, the question of where system boundaries should be drawn in a life cycle analysis, and the need to consider both distant and local impacts which arise from the end-use demands of urban populations. The paper explores these issues, through the use of modelling results from the case studies. Particular emphasis is placed on the communication of research results to policy makers, interested organisations and the public, drawing on recent experience with the dissemination of results from the project's first case study relating to waste-paper management options.     

A protocol for assessing the effectiveness of oil spill dispersants in stimulating the biodegradation of oil

Dispersants are important tools in oil spill response. Taking advantage of the energy in even small waves, they disperse floating oil slicks into tiny droplets (<70 μm) that entrain in the water column and drift apart so that they do not re-agglomerate to re-form a floating slick. The dramatically increased surface area allows microbial access to much more of the oil, and diffusion and dilution lead to oil concentrations where natural background levels of biologically available oxygen, nitrogen, and phosphorus are sufficient for microbial growth and oil consumption. Dispersants are only used on substantial spills in relatively deep water (usually >10 m), conditions that are impossible to replicate in the laboratory. To date, laboratory experiments aimed at following the biodegradation of dispersed oil usually show only minimal stimulation of the rate of biodegradation, but principally because the oil in these experiments disperses fairly effectively without dispersant. What is needed is a test protocol that allows comparison between an untreated slick that remains on the water surface during the entire biodegradation study and dispersant-treated oil that remains in the water column as small dispersed oil droplets. We show here that when this is accomplished, the rate of biodegradation is dramatically stimulated by an effective dispersant, Corexit 9500®. Further development of this approach might result in a useful tool for comparing the full benefits of different dispersants.     

Sulfate Emissions from Vehicles on the Road

Experiments have been conducted to measure vehicle sulfate emissions, by vehicle type, at two tunnels on the Pennsylvania Turnpike. A satisfactory balance between estimated fuel sulfur consumption and observed emissions of sulfur compounds corrected for ambient-air contributions was obtained. This work started in 1974 before the introduction of catalyst-equipped automobiles and continued into 1976. The sulfate contributed by vehicles even in the tunnels was found to be generally modest relative to rural ambient sulfate levels. Average sulfate emission rates were found to be ~30 mg/km (50 mg/mi) from heavy-duty Diesel trucks, <15 mg/km from catalyst-equipped cars (probably in the range 4 to 7 mg/km), and probably <1 mg/km from non-catalyst cars. The overall SO₂ —* SO₄ ^-2 conversion of the vehicle emissions was 2 %.     

Development of a 24-Hour Method for Analysis of SO2 and CO2 from Electric Utility Units Equipped with Flue Gas Desulfurization Scrubbers

A procedure was developed for the 24-h determination of SO₂ and CO₂ in effluent gas from fossil fuel combustion sources. Laboratory experiments were conducted to test absorption of SO₂ in hydrogen peroxide solution and absorption of CO₂ by sodium hydroxide on an inert substrate at expected ambient temperatures of 15 to 45°C. Isopropyl alcohol cannot be used to trap sulfuric acid and particulates because it permeates the sampling train and prevents complete absorption of CO₂. Elemental analysis of stack particulates revealed that at least 31 elements were present. Iron and other elements interfered with SO₂ analysis. These particulates were completely removed by a heated borosilicate glass filter. Both laboratory and field experiments showed that molecular sieves are a promising alternative for CO₂ absorption. Statistical evaluation of data collected at three units equipped with flue gas desulfurization scrubbers proved that the new procedure is accurate and precise.     

Metrics for integrating sustainability evaluations into remediation projects

The US Sustainable Remediation Forum (SURF) created a compilation of metrics (Metrics Toolbox) in response to a need for a broad set of metrics that could be used to assess and monitor the effectiveness of remedies in achieving sustainability goals. Metrics are the key impacts, outcomes, or burdens that are to be assessed or balanced to determine the influences and impacts of a remedial action. Metrics can reflect any of the three aspects of sustainability (i.e., environmental, social, or economic) or a combination of these aspects. Regardless, metrics represent the most critical sustainable outcomes from the perspective of the key stakeholders. The Metrics Toolbox is hosted online at www.sustainableremediation.org/library/guidance‐tools‐and‐other‐resources . By selecting metrics from the Metrics Toolbox as a starting point and considering a potentially wider suite of metrics in remedial program decisions, appropriate assessments can be made. Qualitative and quantitative metrics are tabulated for each remedial phase: remedial investigation, remedy selection, remedial design, remedial construction, operation and maintenance, and closure. Attributes for each metric are described so that remediation practitioners and key stakeholders can view the universe of metrics available and select the most relevant, site‐specific metrics for a particular site. For this reason, SURF recommends that remediation practitioners consider the metrics compiled in the Metrics Toolbox as a companion to the sustainable remediation framework published elsewhere in this journal and other sustainability evaluations. © 2011 Wiley Periodicals, Inc.     

Reactive transport modeling of remedial scenarios to predict cadmium,copper, and zinc in north fork of Clear Creek,Colorado

The North Fork of Clear Creek (NFCC), Colorado, is an acid‐mine‐drainage‐impacted stream typical of many mountain surface waters affected by historic metal mining in the western United States. The stream is devoid of fish primarily because of high metal concentrations in the water (e.g., copper and zinc) and has large amounts of settled iron oxyhydroxide solids that coat the streambed. The NFCC is part of the Central City/Clear Creek Superfund site, and remediation plans are being implemented that include treatment of three of the main point‐source inputs and cleanup of some tailings and waste rock piles. This article examines dissolved (0.45‐μm filterable) concentrations of cadmium, copper, and zinc following several potential remediation scenarios, simulated using a reactive transport model (WASP4/META4). Results from modeling indicate that for cadmium, remediation of the primary point‐source adit discharges should be sufficient to achieve acute and chronic water‐quality standards under both high‐ and low‐flow conditions. To achieve standards for copper and zinc, however, the modeling scenarios suggest that it may be necessary to treat or remove contaminated streambed sediments in downstream reaches, as well as identify and treat nonpoint sources of metals. Recommendations for improvements to the model for metal transport in acid‐mine drainage impacted streams are made. These recommendations are being implemented by the U.S. Environmental Protection Agency. © 2009 Wiley Periodicals, Inc.     

Evaluating aeration techniques for decreasing phosphorus export from grasslands receiving manure

Because surface-applied manures can contribute to phosphorus (P) in runoff, we examined mechanical aeration of grasslands for reducing P transport by increasing infiltration of rainfall and binding of P with soil minerals. The effects of three aeration treatments and a control (aeration with cores, continuous-furrow "no-till" disk aeration perpendicular to the slope, slit aeration with tines, and no aeration treatment) on the export of total suspended solids, total Kjeldahl P (TKP), total dissolved P (TDP), dissolved reactive P (DRP), and bioavailable P (BAP) in runoff from grasslands with three manure treatments (broiler litter, dairy slurry, and no manure) were examined before and after simulated compaction by cattle. Plots (0.75 x 2 m) were established on a Cecil soil series with mixed tall fescue (Festuca arundinacea Schreb.)-bermudagrass [Cynodon dactylon (L.) Pers.] vegetation on 8 to 12% slopes. Manures were applied at a target rate of 30 kg P ha(-1), and simulated rainfall was applied at a rate of 85 mm h(-1). Although the impact of aeration type on P export varied before and after simulated compaction, overall results indicated that core aeration has the greatest potential for reducing P losses. Export of TKP was reduced by 55%, TDP by 62%, DRP by 61%, total BAP by 54%, and dissolved BAP by 57% on core-aerated plots with applied broiler litter as compared with the control (p < 0.05). Core and no-till disk aeration also showed potential for reducing P export from applied dairy slurry (p < 0.10). Given that Cecil soil is common in pastures receiving broiler litter in the Southern Piedmont, our results indicate that pairing core aeration of these pastures with litter application could have a widespread impact on surface water quality.