微波修复原油污染土壤的均匀设计实验

采用均匀设计实验方法,研究了微波修复原油污染土壤时原油去除率与微波能耗、含水率和含炭率等因素的关系,并应用MATLAB编程拟合出经验公式。结果分析表明:微波能耗在0～288 kJ范围内,污染土壤的原油去除率随微波能耗线性增加;在含水率为6%、含炭率为4%、微波能耗从0增加到288 kJ时,原油去除率从0%增加至92.3%;含炭率在0%～4%范围内原油去除率与含炭率成线性关系,在微波能耗为288 kJ、含水率为6%、含炭率从0%增加到4%时,原油去除率从12.3%增加至92.3%;原油去除率与含水率成二次曲线关系且开口向下,微波修复原油污染土壤的最佳含水率为6.6%。研究结果对微波修复原油污染土壤技术的优化提供了有价值的参考。     

外源Cd对不同利用方式红壤脲酶活性的影响

采用室内培养实验,通过将外源Cd添加到同一母质、全镉含量相近的不同利用方式的红壤中(林地、水稻土和菜园土),研究了外源Cd污染对不同利用方式红壤脲酶活性的影响。结果表明:整个培养过程中,Cd污染对3种红壤脲酶活性都有抑制作用,且随重金属浓度的增强而增强。同剂量Cd污染对3种红壤脲酶活性的抑制效应不同,大小为林地>水稻土>菜园土。实验设定的Cd处理水平下,对林地、水稻土和菜园土脲酶活性产生显著抑制作用(p<0.05)的Cd浓度分别为5、30和50 mg/kg土。     

基于GCM_CB模型的土壤重金属污染评价

灰色聚类法已经运用于土壤重金属污染评价中,然而此法在确定聚类权重时仅考虑重金属浓度,忽略了衡量重金属毒性强弱的重要指标生物毒性指数。为了更客观和准确地反映土壤重金属的污染程度,将生物毒性指数引入到聚类指标权重中,构建GCM_CB(grey clustering method_concentration and biotoxicity)土壤重金属污染评价模型。通过对华东某地区的10个区域土壤重金属污染进行分析评价,并与常用评价方法对比研究,表明:其多数样点的评价结果基本一致,但针对样品4和样品9中的元素Hg,因其强毒性,使得评价等级由I级定为II级,从而提高了评价方法的灵敏度,更加符合该区域的实际土壤污染情况。     

实时荧光定量PCR对A2/O短程硝化系统内氨氧化菌的定量分析

通过控制好氧区低DO浓度以及缩短好氧实际水力停留时间(actual hydraulic retention time,AHRT),在处理低C/N比实际生活污水的A2/O工艺中,成功启动并维持了短程硝化反硝化;系统亚硝酸盐积累率稳定维持在90%左右,氨氮去除率在95%以上。通过提取富集氨氧化菌(ammonia oxidizing bacteria,AOB)的基因组DNA,经两次常规PCR扩增和琼脂糖凝胶电泳,以纯化回收的DNA扩增片段作为实时荧光定量PCR检测AOB数量的DNA标准品,建立了检测AOB数量的实时荧光定量PCR标准曲线。利用实时荧光定量PCR技术比较了A2/O系统在不同运行条件及亚硝酸盐积累率情况下AOB菌群数量。结果表明,随着系统亚硝酸盐积累率的上升,系统内AOB菌群数量也大幅上升。全程硝化和短程硝化时,系统内的AOB菌群数量分别为5.28×109cells/g MLVSS和3.95×1010cells/g MLVSS。此外,亚硝酸盐积累率的下降相对于AOB菌群数量的下降有一定的滞后性。     

某矿区土壤和地下水重金属污染调查与评价

为了解湘南某矿区土壤和地下水重金属污染状况,对该矿区东河流域附近重金属污染源进行了调查,同时,对地下水和土壤样品进行了采样分析,结果表明：（1）该矿区东河流域附近的主要污染源有18个,其中有色金属选厂、尾矿库、采矿场和冶炼厂是排放重金属较多的污染源;（2）20个采样点中土壤重金属Pb、Cd、Zn、As和Hg大部分超过国家土壤环境质量标准（GB15618-1995）,综合污染指数P综〉1,该矿区主要的重金属污染元素为Cd、As和Hg,且土壤中Cd、Zn和As的含量两两之间存在着极显著的正线性相关关系;（3）重金属元素在土壤中的纵向迁移不明显,该矿区附近20个采样点的地下水并未受到污染,综合污染指数P综〈1。20个采样点地下水Pb、Cd、Zn、As、Hg浓度均能达到地下水质量标准（GB／T14848．9）中的Ⅲ类标准。     

CNTs/TiO2/CS光降解苯的动力学

综合光催化氧化苯的动力学过程、光辐射场模型和质量守恒定律,采用平板型反应器建立了碳纳米管/二氧化钛/壳聚糖(CNTs/TiO2/CS)催化薄膜光催化氧化气相苯的数学模型;该模型考虑了光强、相对湿度、初始浓度与气体流速对气相苯光降解的影响。结果表明,建立的数学模型与实验结果吻合较好。     

The life cycle assessment of an e-waste treatment enterprise in China

Electrical and electronic waste (e-waste) has become one of the fastest growing waste streams in the world, and many countries have established e-waste treatment enterprises to solve their e-waste problems. In this study, a life cycle assessment (LCA) was undertaken to quantitatively investigate the environmental impacts of an e-waste treatment enterprise in China. The LCA is constructed by SimaPro software version 7.2 and expressed with the Eco-indicator 99 life cycle impact assessment method. For a sensitivity analysis of the overall LCA results, the so-called CML method is used in order to estimate the influence of the choice of the assessment method on the result. According to the survey data, discarded TV sets accounted for the highest proportion of e-waste treated in the enterprise in 2010. The e-waste treatment had little environmental impact, and at the same time large environmental benefits can be achieved mainly due to the recycled resources and reuse of some components. Based on the research results, it can be seen that recycled metal, especially copper, would be of more importance for environmental benefits. Relevant results and data from this study could provide decision support to enterprise managers and government sectors.     

Bioaccessibility of polychlorinated biphenyls in workplace dust and its implication for risk assessment

Human exposure to bioaccessible PCBs via indoor dust is limited around the world. In the present study, the workplace dust sample from commercial office, hospital, secondary school, shopping mall, electronic factory and manufacturing plant were collected from Hong Kong for PCBs analyses. Total PCBs concentrations ranged from 46.8 to 249 ng g⁻¹, with a median of 107 ng g⁻¹. Manufacturing plant showed the highest concentration among all of sampling sites. PCB 77 was found as the dominant congeners. The bioaccessibility of PCBs in small intestinal juice ranging from 8.3% to 26.0% was significantly higher than that in gastric condition, ranging from 4.8% to 12.4%. In addition, significant negative correlations (p < 0.05) were observed between K_OW and bioaccessibility for all workplace dust samples. Risk assessment indicated that the averaged daily dose of dioxin-like PCBs via non-dietary intake of workplace dust, considering the bioaccessibility of PCBs, were much lower than the TDI of dioxins (2.3 pg WHO-TEQ kg bw⁻¹ d⁻¹) established by Joint FAO/WHO Expert Committee on Food Additives.     

双氰胺-甲醛聚合物-聚合氯化铝复合絮凝剂的合成及应用

以双氰胺、甲醛、氯化铝为主要原料,加入添加剂合成了双氰胺-甲醛聚合物（DF）-聚合氯化铝（PAC）复合絮凝剂。采用模拟印染废水考察了各种因素对DF—PAC复合絮凝剂混凝脱色性能的影响。实验结果表明,在双氰胺、甲醛、氯化铝、添加剂加入量分别为29．1,57．8,4．8,12．5g,反应温度（70&#177;1）℃、反应时间2．5h的条件下制得的DF—PAC复合絮凝剂的絮凝脱色性能良好,COD去除率不小于90％,色度去除率不小于99％。与PAC和DF絮凝剂相比,DF—PAC复合絮凝剂对实际印染废水的絮凝脱色效果更好。